Search Documents

By M. Barkhudarov

The results are presented of research aimed at validation and development of a general purpose CFD code FLOW-3D. FLOW-3D is a commercial code developed by FLOW SCIENCE, INC. A number of physical modeling experiments involving the filling of cavities of different geometries with coloured water have been performed in order to compare the measurements with the results of computer simulations. Other numerical calculations were also done to be compared with the known analytical solutions.

Jan 1, 1992

By M. S. Lee

A cold model study on the effects of various operating conditions on the dispersed-phase holdup in a liquid-liquid emulsion generated by bottom gas injection has been performed using water and kerosene. Dimensional analysis was used to correlate the holdup with the operating conditions and the sampling locations. The holdup increased with gas velocity, and decreased with axial and radial distances. The radial distribution of holdup follows a Gaussian function. The holdup increased with increasing ratio of the heavy phase to light phase volumes and decreased with the total height of the heavy phase. The combined effects of various operating conditions can be represented by the Froude number. The variation of the holdup within the plume was correlated by a single equation involving a set of dimensionless numbers.

Jan 1, 1995

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By U .. C. Rojas, J .. C. Gomez

"Fire Refined Copper (EI Teniente Three Stars) has been produced at Caletones Smelter of Codelco Chile since almost the beginning of its operations.Due to changing features of the copper market, together with the targets on technical efficiency and productivity, it has become more and more relevant for copper industry to reach both, good final product quality and a proper environmental control.At present, copper refining process at Caletones Smelter takes place in two cylindrical tilting furnaces, where solid fluxes are injected through horizontal tuyeres into the molten bath. (Fig. N2 1)Solid reagents are pneumatically conveyed and injected into the liquid copper bath attaining excellent solid - liquid contact, so the impurities removal efficiencies are found to be high. Same injection tuyeres are used to introduce both oxidising agent (normal air) and reducing agent (reformed gas) into the molten bath. Air or nitrogen is used as conveying gas for solid reagents, depending on the process stage.This pap~r gives a fundamental description of the process and industrial results related to the injection of blend of sodium and calcium carbonates to remove arsenic and antimony, silica and granulated reverberatory slag to remove lead and a mixture of calcium carbonate and mineral coal to reduce the selenium content of the fire refined copper."

Jan 1, 1996

By Juárez T. Julio Cesar, Mendez R. Eliecer, Reyes P. Martín, Flores G. Mizraim Uriel, Teja R. Aislinn Michelle, Hernández C. Leticia, Reyes D. Iván Alejandro

The present study shows the characterization of a zinc concentrate collected at Hidalgo, Mexico, in order to identify its mineralogical species and to propose a leaching methodology for silver recovery. The results obtained by X-Ray Diffraction (XRD) show Sphalerite (ZnS) as the mineralogical matrix and silver into the specie proustite (Ag3AsS3). The techniques of Scanning Electron Microscopy-Energy Dispersive Microanalysis (SEM-EDS) and Polarized Optical Microscopy (POM) identified the presence of sulfides of Fe, Cu, Pb and Zn, in addition to silicates and feldspar. The proposed dissolution method of Ag(I) was carried out with [S2O3 2−] = 0.5 M and [NaOH] = 0.1 M to regulate the medium at pH = 9 for 12 h at 298 K. Oxidation of the concentrate was favored by injection of O2 to a partial pressure of 1 atm. Monitoring of the reaction was carried out by reading the [Ag] and [As] by AAS.

Mar 1, 2017

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By Jordan Mayorga, Joseph Kopp, Robert Boehm, Daniel P. Cook

"Solar generated power has long been considered a useful energy source only for low-energy density and non-mission critical use, such as providing electricity for residential applications. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar- 1 near Las Vegas, have demonstrated that solar does have application to high energy density industries such as materials and chemical production. This paper will discuss the current operating con_guration of the Solar-1 facility and show how proposed modi_cations, such as addition of thermal storage and use of liquid salts as the working uid, can further improve the e_ciency and energy production of the plant.IntroductionThe United States as a nation is the largest consumer of energy in the world at an estimated 29 trillion kWh per year[1], which is roughly 15% of total global energy consumption[2]. On a per capita basis, the United States also leads most of the world, using an average of 96,000 kWh per person[3]. Roughly 40% of the energy consumed in the United States was produced from petroleum, 23% from coal, 23% from natural gas, 9% from nuclear and the remaining 5% from renewable sources such as solar, geothermal, wind, and hydroelectric[1].Energy demands associated with the industrial-scale production of chemicals and materials is a signicant portion of the United States total energy consumption. Roughly 33% of the energy consumed in the United States is used by the industrial sector, with 22% of this amount used in chemical production, 16% used in petroleum rening, and 14% used in the smelting and rening of metals[1]. Energy costs are also a signicant, if not the most signicant, portion of the total production costs for many materials. For example, roughly 30% of the cost of producing aluminum is the electricity used in the Hall-Heroult process [4], while the cost of energy is roughly 15% of the total cost of producing steel products [5].The primary sources of power for the industrial sector have been coal, petroleum, hydro- electric and nuclear. The use of alternative energy sources, e.g. solar, wind, geothermal, for industrial materials production has been slow in coming because they are intermittent and low-energy density sources, i.e. no solar power at night, no wind power when the air is still, etc. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar-1 (NS-1) near Las Vegas, have demonstrated that solar can have application to high energy density industries such as materials and chemical production.This paper will discuss the current conguration of the NS-1 facility, and potential modications to the facility that will increase both its power e_ciency and power density."

Jan 1, 2010

By Bruno Augusto Batista Ribeiro, Felipe Terra Elias, Wagner Moulin Silva

In the pyrometallurgical production of copper from its sulfides, converting in the Peirce Smith (P-S) Converter is still the most widespread method to obtain white metal and blister copper from the matte. Despite the fact of being a century-old process, it is still possible to achieve improvements in the process, by the use of modern tools, one of the most valuable being numerical calculation and computer-aided simulation. The present study presents three cases in which the angle for the gas injection and the number of working tuyeres are changed during the slag blow phase of the converting process. It was noticed that a decrease of the number of tuyeres, followed by an increase in the injection gas velocity, results in improved reaction volume and less stress to the refractory lining. However, an increase in the amount of copper lost to the slag as oxide is likely to occur.

Jan 1, 2014

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By Shadia J. Ikhmayies

In this work the equilibrium temperature-composition phase diagrams of the Si-O2 system were calculated using Thermo-Calc software in the temperature range 500–3000 K. Constituents of stable phases were obtained, and the amounts of certain phases where investigated with the variations in the composition of oxygen and temperature. It is found that quartz with silicon represent a stable phase in the temperature range 500–1150 K, while tridymite with silicon represent a stable phase in the temperature range 1150–1700 K. A liquid phase is found besides tridymite in the temperature range 1700–1750 K, and a stable phase of cristobalite with liquid appears in the temperature range 1750–2000. The maximum amounts of quartz, tridymite, and cristobalite are found at oxygen mole percent of 67.7%.

Mar 1, 2017

By H. Castillo

This paper describes the computer simulation of thermal stress fields generated in the quenching of the ns 415 H Steel automotive parts (Valve Lifters), running the ANSYS Multiphysics software of finite element (FEM). Simulation was performed introducing residual stress measurements on specific values areas, like internal pressure condition in the material. The stress condition effect in the material and the properties as temperature function data, were introduced to the FEM software. The thermal stress simulation was made on the 2D system. The parts were austenized to 850 900 °C and then oil quenched, tempered at 150 -200°C, and air cooled. The X-Ray diffraction technique was made to take measurements from residual stresses on valve lifters surfaces. The results analysis showed the ideal stress condition necessary in raw material to reduce the scrap percent in grind operations after hardening heat treating process. Keywords: Thermal Stresses, Temperature profile, Computer Simulation, Finite element analysis, Quenching of steel, Residual Stresses

Jan 1, 2003

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By David T. Bunney

In .December of 1987, International Mill Service, Inc. signed an exclusive licensing agreement with Tetronics Research & Development Co. Limited of Faringdon, Oxfordshire., England to commercialize plasma technology which had been demonstrated in an EAF dust processing application. The intent of the process is to reduce and volatize the zinc, lead and cadmium oxides inherent in EAF dust and collect these elements as metals in an ISP (Imperial Smelting Process) zinc splash condenser, and to render the resultant slag an inert, non-hazardous material. With these objectives in mind, IMS started commissioning facilities in 1989 at Florida Steel in Jackson, Tennessee and Nucor-Yamato Steel in Armorel, Arkansas. This paper will address the commercial development and progress of the technology at these two installations. Process Description In the EAF steelmaking process typically the off gas stream is cleaned by some form of baghouse. The particulate collected is known as Electric Arc Furnace dust and has been designated by the U.S. EPA as hazardous waste number K061, once it leaves the collection system. This designation was given to the material due to the high toxic concentrations of lead and cadmium (nickel and chromium for stainless EAF dusts) inherent in the dust. IMS' method of operation is to locate the facilities on the client mill's property adjacent to the baghouse. The dust is transported directly to IMS via a closed conveyance system. This method enables the technology to be an additional processing step in the steelmaking process. Once the dust has been transported to the IMS facility, it is fed, metered and mixed mechanically in the feed conveyance system with a carbon reductant (typically coke breeze). The carbon reductant is approximately 10% of the dust feed rate. This mixture passes through the feed system and enters the furnace

Jan 1, 1992

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

By Y. Moriya, Y. Sadayoshi, Y. Nonogaki, Y. Takeda

"Preparation and growth processes of CaF2 on Si(111) and of . InxGa1-x,As islands on CaF2 by molecular beam epitaxy (MBE) are described. It was found that first of all the Si(111) surface treatment process to obtain the 7x7 reconstructed structure was necessary to ensure the cleanness of the surface and to grow a flat and high quality CaF2 on it. Growth of InxGa11-x,As islands on CaF2 was tried by droplet heteroepitaxy using the same MBE reactor. In,GaxGa1-xAs islands were successfully grown epitaxially, and the size and density of the islands dependent on the In composition were investigated.IntroductionThough semiconductor/semiconductor heterostructures are widely used for many device applications, small band off-sets of the conduction bands and the valence bands restrict the utilization of the intra-subband transitions to far-infrared regions. With InAs as the quantum well and fluorides as the barrier layers, we can design three-electronic-level systems in the infrared region, which is the low loss transmission window of the silica optical fibers. To realize those structures, we have grown InxGa1-xAs islands on CaF2 thin films that were epitaxially formed on Si(111) substrates by molecular beam epitaxy. By the droplet heteroepitaxy that we invented, the InxGa1-xAs islands with height of -10 nm have been obtained successfully. Optimum processing to obtain atomically smooth surfaces of Si and CaF2 and high quality InxGa1-xAs islands is reported.ExperimentsMBEMachineCaF2 was grown on Si(111) and InxGa1-xAs islands were grown on CaF2 successively by MBE. The MBE machine consisted of a growth (or reactor) chamber and a loading chamber. The reactor chamber was equipped with Ga, In, As and Er metal source cells and CaF2 and BaF2 source cells. Cell materials were P-BN for Ga, In and As metals, and were graphite for CaF 2, BaF 2 and Er to avoid reaction with BN cells. The electron gun and screen were attached to the reactor to observe the RHEED pattern during the substrate surface treatment and the growth of CaF2 and InxGa1-xAs islands. The substrate manipulator was designed to heat up the Si substrate up to 1,200°C for the surface cleaning. The QMS was also equipped to analyze the residual gas species in the reactor chamber. The base pressure of the reactor chamber was 2-5x10-11 Torr, being pumped by ion pump and the liquid nitrogen shroud"

Jan 1, 2000

By Anna Franzkowiak, Dean Gregurek, Alfred Spanring, Angelika Ressler

In order to determine the most suitable refractory products and improve the lining lifetime for the diverse furnaces used in the nonferrous metal industry, corrosion tests are performed at RHI’s Technology Center. The practical facilities include the cup test, induction furnace, rotary kiln, and drip slag test described in this paper, which enable a comprehensive understanding of the chemo-thermal brick wear on a pilot scale. The corrosion trials are performed with actual slags generated during operations at a customer’s plant. To determine the highest influencing wear parameter, every single test is combined with a detailed mineralogical investigation and thermochemical calculations performed using FactSage. Based on the results, tailored refractory solutions for the nonferrous metal industry can be provided in combination with trials conducted at the customer’s site.

Jan 1, 2014

By David J. Krichten

A method of retrofitting air-fuel burners with oxy-fuel capability overcomes the potential problems associated with oxygen combustion in aluminum melting furnaces. The retrofit burner uses the existing combustion air connection, burner housing, and burner tile and replaces the gas tube with an oxy-gas burner. Maintaining a portion of the air flow to the burner reduces the potential for localized overheating. Proper design of the burner reduces NOx emissions by moderating the flame temperature with furnace gas recirculation. Economic analysis of using oxygen shows the benefits are increased productivity and reduced overall unit cost of melting. In practice, the melt rate in rotary furnaces increases by up to 50% and by up to 35% in reverberatory furnaces. Oxygen utilization reduces total melting cost by 112-314 cents per pound of aluminum melted.

Jan 1, 1997

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008