Search Documents

By Peter V. Barr

Despite the advent of modem firing control systems reheating furnace operations frequently allow significant thermal excursions in the discharged slabs or billets after furnace delays. Although HSM furnaces are not immune to this and other related problems, mini-mill operations are most vulnerable due to their more frequent delays and (often) less sophisticated control systems. In order to reduce these problems control systems will commonly include a thermal model, operating either on-line (interacting directly with the controller logic) or in an advisory, off-line mode. Using a new 'fast' thermal model, the paper examines the thermal response of a typical mini-mill furnace during both delays and the subsequent recovery period. A variety of firing strategies are explored and compared on the basis of maintaining thermal excursions within allowable limits for rolling. Other factors, such as the potential for overheating of billets within the furnace during delays and the overall thermal state of the furnace, are also considered in some detail. Although common practice, the use of conventional thermocouple zone temperatures for furnace control during and after delays is shown to be a dubious proposition. Keywords: Reheat Furnace, Modeling, Process Control

Jan 1, 2003

By Sun Ying, Zhang Jing, Li Qiu-ju, Wang Yan-ze

Copper smelter slag was leached using sulphuric acid solutions under atmospheric conditions. Base on the composition and phase of copper slag, the effect of the concentration of sulfuric acid and leaching temperature to the leaching growth rate of Fe, Cu, Co and Ni in the copper slag were investigated in this paper. Simultaneously, the influence of sulfuric acid concentration, leaching time, leaching temperature and the amount of sulfuric acid (solid-liquid ratio) to the leaching rate of these metal elements were researched. Experimental results showed that: with the increasing temperature, the dissolution rates of the metals elements increased first and then decreased. Due to the influence of silica gel which was obtained in beginning of leaching, the higher the concentration of sulfuric acid is not conducive to dissolution of the valuable metal elements. The dissolution degree of Fe, Cu, Co and Ni were 92.83% 96.76% 93.62% and 63.41% respectively.

Jan 1, 2016

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Lijun Liu, Yingwei Li, Jianhua Liu, Jinhui Peng

"As essential equipment in the metallurgical industry, current air heat exchangers cannot meet the requirements of high temperature heat transfer. In this paper, an energy efficient air heat exchanger, based on accumulation of the heat generated by microwave absorbing materials, is presented according to heat transfer theory and principles of the microwave field. A tubular shaped heat exchanger was designed and built up through temperature-rising curve, and experimental research of microwave high-temperature air heat exchangers was carried out. It was found from experiments that the tubular shaped heat exchanger fabricated using material B could be used for high temperature heat transfer system, and equilibrium temperatures could reach up to 457—485?.IntroductionHeating or cooling of air by heat exchangers is commonly practiced in a wide range of industries including construction, chemical, machinery, textile, printing, and dyeing [1-3]. Generally such heating or cooling of air is achieved in pipe heat exchangers. There are several drawbacks for such heat exchangers, namely, (i) the limitation of temperature to which the pipes can be heated, (ii) tendency to oxidize at high temperature, and (iii) poor strength of metallic pipes at high temperature. These limitations do not allow pipe heat exchangers to be operated at high temperatures [4-6].Microwave heating of inert solids, which are stable at high temperature, is a possible solution to achieve high temperature of the medium in air heat exchangers. It is well-known that microwave heating is an efficient, clean, safe, easy-to-control heating method. Microwave heating utilizes the dielectric and magnetic properties of a material. When microwaves penetrate and spread into the dielectric material, electrons, ions, etc move in the internal electromagnetic field, while the elasticity of inertia and friction impede these movements. This results in a significant thermal effect, increasing the surface temperature rapidly [7-8]. This paper studies mainly design and experimental research of microwave high-temperature air heat exchanger."

Jan 1, 2011

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Shigehisa Endoh, Hitoshi Ohya, Atsushi Inaba, Shigeki Koyanaka

"Recycling should be promoted to keep the global environment. However, it is difficult to detennine the quantitative impact. A life cycle assessment is one of the most reliable methods to estimate the global environment impact.Exergy is useful like entropy when considering the sustainable development. All of our activities have been obtained exergy resources and/or energy itself and throw away waste and/or waste heat. We are trying to use exergy to estimate the quantity of energy and matter for resource accounting. For recycling plastic, plastic has two aspects; material and energy source.The environmental assessment of plastic recycling suggests that the exergy reduction of the entire system is estimated by the yield of matter and the process efficiency. The material recycling is better than the thennal recycling when the process efficiency is high. However, the thennal recycling is much better for the low efficiency. The transition point is able to be decided by the efficiency of the manufacturing and the electric power generation.IntroductionRecently, many of the global environmental problems have become conspicuous like global wanning, ozone layer depletion and acid rain. Some of the methods like life cycle assessment for solving these problems have been presented. Anxiety concerning the proble1ns of energy and resources has led to a rapid increase in the interest in describing and understanding the conversion processes of energy and other resources in today's society. All human activity is supported by obtaining power and products of high exergy from the environment and throwing away the waste material and the waste heat of low exergy back the environment. However, the total exergy in the whole system becomes absolutely smaller than before.The rate of obtaining high exergy products and energy itself by human activity and the speed, by which waste and waste heat having low exergy are thrown away are too fast to attribute to environmental problems [1-3].A material's use by recycling was often common in a circulating society mainly. A significant amount of energy is consumed during circulation. An environmental impact assessment method for the process or the system has not been devised when both of them are taken into consideration. Even if the life cycle assessment evaluation, which has been correctly used up to now, is applied, it is not sufficient for an overall evaluation concerning matter and energy.The real sustainable development is that the exergy reduction value by all human activities on the earth is kept within the range of the exergy reduction in order to consider the earth as closed stationary system. It is important to evaluate the process or the system by using the exergy, and design them so that the exergy loss may decrease as much as possible. We have to consider what process improvement is the most effective."

Jan 1, 2000

By P. D. Navarro

The behavior and operability of LIX 1104SM extraction was studied at laboratory scale on the Solvent Extraction at Sb3+, from high concentration sulfuric acid. In order to evaluate the reactant batch tests were made at laboratory scale as well for extraction as for re-extraction of Sb3+. Experiences achieved were: extraction kinetics, temperature effects, selectivity tests and re-extraction selectivity. A extraction kinetics was found, reaching equilibrium in 2 min, high selectivity of Sb3+ extraction in front of Cue , existing As5+ co-extraction and Fe3+ At the re-extraction stage, equilibrium was reached in 3 min, getting high Sb3+ re-extraction efficiency with HCl concentrations within 6 and 8 M. A high selectivity was achieved on Sb3+ re-extraction in front of As+5, existing Fe+5 re-extraction.

Jan 1, 1999

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006

By Qingwei Qin, Ping Xue, Guangqiang Li

Ausmelt furnace slag contains about 0.9% Cu (mass %). With increasing the amount of Ausmelt furnace slag, the recovery of copper from it will produce an enormous economic yield. The recovery of copper by floatation from slow cooled Ausmelt furnace slag was studied in this paper. The phases and composition of the slow cooled slag were analyzed. The factors which affected the copper recovery efficiency such as grinding fineness, pH value of flotation medium, different collectors and floating process were investigated. It was shown that the size distribution of the primary grinding and secondary grinding of middling were 75% for particles less than 0.074mm and 82% for particles less than 0.043mm respectively. The closedcircuit experimental results with butyl xanthate as collector in laboratory showed that the copper grade reached 16.11% and the recovery rate of copper reached 69.90% and the copper grade of tailings was only 0.2%.

Jan 1, 2015

By Kota Nakashima

Residues from titanium smelting tend to contain scandium. The scandiumis discarded because no suitable process exists for its recovery from the residue. Valuable-metal recovery from discharged residue is critical for environmental conservation and to achieve a sustainable society. Since 2015, JXNippon Mining&Metals has been developing a process for scandium recovery from the residue of a titaniumsmelting process. The process consists of the following steps: scandium concentrating by classification or neutralization, selective scandium leaching, impurity removal by neutralization, solvent extraction of scandium by using D2EHPA, purification, and roasting. We optimized the above steps to achieve an effective process to obtain scandium oxide (Sc2O3). In this paper, we introduce results from the bench-scale test of the scandium recovery flowsheet developed by JX Nippon Mining & Metals.

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By J. Sofra

The quantity of copper produced by secondary material processing is increasing as metal producers look to cleaner and cheaper sources of copper. The need to smelt secondary copper more economically, to process a wide range of materials with large fluctuations in size and composition and to cope with the increasingly stringent environmental constraints have put considerable pressure on existing conventional secondary copper smelters. The Top Submerged Lance process, developed and commercialized by Ausmelt Ltd offers a low cost technology, which is particularly adapt at processing copper-bearing scrap and residues. The application of Ausmelt Technology to replace conventional secondary copper processing operations introduces potential for significant advantages in environmental performance, and improved process efficiencies through the use of cheaper hels and reductants, the high rate of metal recovery and the flexibility inherent in the technology to process various feed material types. The economical, process and environmental benefits of its application are highlighted for both the smelting and converting stages of copper production.

Jan 1, 1997

By Hong-ying Xia, Bao-bao Wang, Jin-hui Peng, Bing-guo Liu, Li-bo Zhang, Zhi-qiang Li

Based on optimization using response surface methodology designed by Box- Behnken, to study the interaction of wet industrial salt with moisture drying temperature (50-90 ); duration (10-50s); and the weight of the materials (20-60g). The results show that: the experimental parameter conforms to the quadratic equation model to influence the moisture content and the dehydration speed., in analyzing the significance and the interaction of various factors, the optimum by the Design Expert software conditions for drying with microwave radiation include temperature of 90 , duration of 10s, and sample mass of 26g. Verified by experiment, the moisture content after drying is less than 0.25% and the dehydration rate reached 1.37g/min, between the predicted value and the actual value confirmed good fitting degree.

Jan 1, 2015

By H. A. F. de Souza, Dana S. Mills, P. E. Burgener

"ICP-MS has moved from a laboratory curiosity to a functional analytical tool. This paper discusses how ICP-MS has been used to solve difficult analytical problems encountered when analyzing various mine materials. Comparisons between analytical techniques applied to the analysis of gold and the platinum group metals illustrate the advantages and problems of ICPMS when. applied to trace levels of some metals iri the presence of ore grade metals. Interferences and matrix effects are compared to ICP, AA and Neutron Activation. The necessity to select chemical extractions which are compatible with ICP-MS are also discussed.The ICP-MS techniques explained in the examples on Au and precious group elements (PGE) have validity in analytical problems encountered in testing of trace metals in the presence of major elements found in mine materials. Exploration and environmental testing are other areas that require the same analytical approach to quantify trace levels in the presence of major interfering elements normally associated with mining environments."

Jan 1, 1999

By Shengli Wu, Jinming Zhu, Wei Huang, Xinliang Liu

The sinter of high basicity would interact with lump ores or acid pellets in the cohesive zone of blast furnace due to the difference of chemical composition and micro structures. The results of this work showed that the softening-melting properties of lump ores and acid pellet would be obviously improved by the high temperature interaction. However, the high temperature interaction index (INI) would be influenced by many factors, such as chemical composition, porosity, interaction interface and so on. The INI between sinter and porous limonite lump ore (L-2) was much higher than that of dense hematite lump ore (L-1) and acid pellet (P-1). In addition, though the softening and melting properties of L-2 were poorest in respective iron ores, the softening and melting properties of integrated burden B (consist of sinter and L-2) were not worse than other integrated burdens due to the strong high temperature interaction.

Jan 1, 2015

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By Cyro Takano

An alternative use for recycling of waste from bag house of iron ore sinter plant was tested by producing and evaluating" at laboratory scale, the self reducing cold bonded pellets. This waste was characterized and the self-reducing pellets were produced using anthracite coal fines as reductant and Portland cement or hydrated lime/Blast Furnace slag as binder. It was used the molar ratio of Fe2O3/C (fix) equal to 3. Evolution of cold strength with curing time, for different contents of binder, was evaluated. Cold strength of 200N/pellet was obtained, for sinter dust, after 10 days of curing. Suitable hot strength was also presented and no decrepitation and swelling were observed. Good fractional reduction was obtained at 950°C and 1137°C. These results show that this material may be used by the Self-Reducing Processes for hot metal production, as an alternative route for this dust destination.

Jan 1, 1996

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015