Search Documents

An iridium oxide coated titanium electrode was tested as anode in copper electrowinning. Initial results confmed that the DSA-type anode was significantly more active for oxygen evolution than traditional lead anodes. However, during longer runs, the anode potential was observed to increase linearly at a rate of 220 mV/year. Scanning elecuon microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the anode passivation could be attributed to elecuochemical dissolution of the coating. The effect on the anode potential of organic additives (glue and thiourea) and lead in solution was also examined. A preliminary economic evaluation of the anodes is given.

Jan 1, 1992

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By R. J. Wesely

The paper describes the various methods which are currently being used or considered to refine gold and silver. These methods are then compared on a technical and economic basis. Conclusions are drawn on the factors which might influence the choice of process for different feed stocks and economic constraints

Jan 1, 1990

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Joel A. Huffinan

"This presentation is being given to better inform the audience of the dependability of precious metal analysis by fire assay. A brief explanation, however, of standard fire assay exploration procedures will be given. An overview of other types of analyses by fire assay will be discussed as well, and the operation of a modern day assay laboratory.IntroductionThe use of lead oxide for the fire assay process dates back to the finds in Troy II and the Cappadocian Tablets about 3,000 B.C. Some advances have been made in the basic procedures due to instrumentation and electronics, but the fusion and cupellation procedures used in fire assay remain much the same as during this period.In 1600 AD. Agricola was the first to take a scientific approach to fire assay recording methods and procedures used (Hillerbrand and Allen, 1905) [1]. Since this period, much of the recognized research into the analysis of ores and metals was carried out in the late 1800's and early 1900's prior to World War II, and again after the deregulation of precious metals. The renewed interest in precious metals mining and metallurgy are due much to advances in precious metals heap leaching in late 1970's."

Jan 1, 1999

By William C. Spindler

Five industrial installations of large lead-acid battery energy storage systems in operation in the United States, West Germany and the 'Republic of South Africa will be described. One example is for a deep mine shaft in which air ventilation and personnel evacuation require the highest reliability for emergency power. The battery system is designed for additional cost-effective benefits of peak load lopping and reactive power control. Commercially available lead-acid batteries of the following types are in use1 traction, truck, submarine, high power, and gel. Electrode grids of both the calcium and antimony alloy types are used. Applications include deep and shallow cycling as well as float and intermittent use. The advantages of sealed lead-acid batteries in UPS (uninterruptible power source) systems are well established throughout the world, and such system suppliers could readily develop markets for industrial emergency and peak power lead-acid storage battery installations.

Jan 1, 1990

By Bogdan Petkovic, Boban Todorovic

In the early 90's a completely unknown problem was encountered at the converter Department: it was a chronic shortage of the cold copper charge needed for the second operating period. A high temperature operating regime was caused which further provoked a chain of consequences such as a drastic drop of the number of operations in campaigns. The consumption of repair bricks reached the quantity of 8.3955 kg / tonne of anode Cu. In 1994, we won the process of cold material smelting during the "copper" blowing [2]. The number of operations per campaign reached 180-200 again. Also in 1994 we won the process of smelting cold materials to obtain "tin" blowing with the purpose of completing their processing cycle [2]. During the period 1994 – 2007 a total of 107,845 tonnes of cold material were remelted to make copper and 56,794 tonnes were re-smelted to obtain "tin". Upon synthesizing these two processes, a completely new model was achieved in 2005, by Bogdan Petkovic, which entirely utilized all available energy of the Peirce-Smith (PS) converters of the Bor Copper Smelter and now represents the basis of the time cycle. The cold material now enters the converter plant, copper recovery is increased and the method itself is environmentally friendly. 167

Jan 1, 2009

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By Andres Vikdahl

The Rönnsktär smelter has recently undergone a series of technical and operational changes. This changes are caused by our own will to remain and gain in competivety and to adapt to the ever changing surroundings. To be able to remain competitive in surrounding with high wage costs, high inflation and high environmental standards thorough cost management is needed. The Swedish economic policy in the beginning of the 80'ies consisted amongst other things of two devaluations. The exchange rate of the Swedish Krona was reduced with approximatively 25 %. This boosted the profits of our export industry, some even believed we entered the land of milk and honey ... And working in this promised land where everything turns into profit it is very difficult to be careful and restrictive with your spendings. Apart from some healthy and fruitful investments we allowed ourselves yearly steady increases in salary for ever reduced number of worked hours and we of course employed more people. Inflation rates went up and so did property prices. In 1986 finally reality catched up on us. Reality in the form of too high costs started to hit Swedish export industry 5-6 years after the big devaluations. Furthermore the high inflation rate also hit the domestic industry a couple of years later. Together with other important factors Sweden faced a severe home-made recession in the beginning of the 90'ies. With this background we now report and analyse our smelter's performance and operating results, shown in fig 1 The main constrictions on smelting and refining at Rönnsktär are today: * Income restrictions by governmental production level Limit * Throughput resmctions by governmental emission limit * High capital costs in the aftermath of Swedish high inflation in the recent decade * Low work force turnover Below we will illustrate how we tackled with these issues along the following lines: * People * Quality * Technology

Jan 1, 1993

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By C. E. Abbey

Cobalt, iron and manganese play various roles in copper electrowinning using lead–calcium–tin alloyed anodes. Cobalt catalyzes electrochemical water decomposition resulting in lower anode potential and reduced corrosion rates. Iron reduces cathodic current efficiency, but is used to reduce higher oxidation states of manganese that oxidize organics in solvent extraction. Manganese also produces anode scale and is generally considered a problematic impurity. The effect of the combined interaction of these three metal ions on the anode potential has not been quantified yet. The current work used a three factor, two level, three replicate central composite design of experiments to analyze the effects and potential interactions among cobalt, iron and manganese. The experiments consisted of chronopotentiometric analysis to assess anode potential after 24 h of operation. Higher [Co], lower [Mn] and either high or low [Fe] yielded lower anode potentials. Two regression models were developed to predict anode potential as a function of [Co], [Fe] and [Mn]. A method to estimate electrical energy consumption for copper electrowinning is also presented.

By A. P. Pavia

Investigation on profitable ways to recover significant quantities of silver remaining dissolved in highly concentrated chloride solutions frequently pass through the development of solvent extraction (SX) routes. In this work, the general pathways involving Ag(I) extraction by dibutylthiourea (DBT) or tetraethylthiuram disulfide (disulfiram, DSF), from concentrated acidic chloride solutions, are investigated. With this purpose, the dependence of Ag(I) distribution coefficient on ligand and chloride concentrations has been analysed. Furthermore, in order to check whether there is some protonation at any site of DBT or DSF after contact with adequate chloride phases, lH NMR has also been used. The collected spectroscopic data suggest that anionic Ag(I) extraction reactions are not likely to occur. Based on the overall results achieved, proposals for the most probable Ag(I) extraction reactions are made.

Jan 1, 2001

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Wei Yin, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Copper anode slime is an increasingly significant resource for precious metals such as Au, Ag and Pd. The extraction of Au, Ag and Pd from decopperized anode slime by different pretreatments and different lixiviants including cyanide, chloride, thiourea and thiosulfate have been investigated. When oxidizing roasting pretreatment was carried out under the conditions of roasting time 120min and temperature 625 ℃, the removal ratios of S and Sb could reach 82.18% and 98.52%, respectively. And the following alkaline leaching of calcine could result in the dissolution of 46.40% Cu and 98.48% Pb. The optima leaching ratios of Au, Ag and Pd reached 99.48%, 97.69%, 94.79% by cyanide leaching, and 95.01%, 79.84%, 96.59% by chloride leaching, and about 95.21%, 95.66%, 48.79% by thiourea/thiosulfate leaching.

Jan 1, 2015

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported' Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003