Search Documents

By M. Mujahid, A. Maqsood, M. H. Asghar, K Iqbal

"Thin film multilayer anti-reflection coatings (Si02/Si/Si02) having thicknesses 286/571/143nm were deposited by RF magnetron sputtering deposition technique on 0.5mm thick Si(100)-substrates. Post-deposition annealing is also carried out in the temperature range 150-650°C for 4hr at the rate of 10°C /min. Si Optical window was designed at 4.21lm wavelengths and correlated with modeling software. The films are transparent in the 3-51lffi band of the electromagnetic spectrum, firmly adhered to the substrate. The prepared multilayer thin films are characterized optically and structurally using a spectrophotometer, an atomic force microscope, x-ray diffraction and a scanning electron microscope. Optical and structural characterizations show that the %transmittance is between 60% and 75%, no appreciable change in crystal structure and roughness of coatings vary between 9 and 25 nm when annealed in the temperature range of 150-650oC. Local elemental characterization on the surface of the thin film was carried out using energy dispersive spectroscopy. The quantitative result of energy dispersive spectroscopy has also shown that the ratio of Si to 0 on the film is 0.67: 1.IntroductionSi02 thin films have unique properties in the interfaces with Si and most studied materials in the field of microelectronics and optical devices [1]. Multilayer thin films are using nowadays in the design and fabrication of the shrinking systems with a variety of fields such as optoelectronic devices. The physical properties and parameters can be controlled at scales of microns down to nanometers by using RF magnetron sputtering system [2].Silicon and Silicon dioxide are used as coating materials [3]. These thin films are laid on top of each other in SiO2/Si/Si02 order by RF magnetron sputtering on top of a substrate as given in Table 1."

Jan 1, 2012

By Hector Carreon

During fretting, high points or asperities of the mating surfaces adhere to each other and small particles are pulled out, leaving minute, shallow pits and powdery debris. Sometimes these surface conditions are neglected, but they are important in some application such as the aerospace industry. In this research work, non-contacting and contacting thermoelectric power techniques are performed in fretted 7075-T6 and Ti-6Al-4V samples. It has been found that the contacting and non-contacting thermoelectric power measurements are associated directly with the subtle material variations such as work hardening and residual stresses due to plastic deformation produced in the fretting zone but surface topography. Therefore, both techniques could be used for a global characterization of the most relevant fretting induced effects. Potential of these techniques to monitor subsurface changes in other severe surface plastic deformation processes are clearly envisaged.

Jan 1, 2015

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By Weizhi Zeng, Michael L. Free, Sayan Sarkar, Prashant K. Sarswat

Black Phosphorus was recently discovered as a 2D material and it exemplified huge prospects for application in electronics, optoelectronics, photonics and catalysis. It is a direct band semiconductor with tunable band gap varying from 0.35 eV (bulk) to 2 eV (single layer). But the layer dependent band gap of black phosphorus restricts it to make use of the full spectra of sunlight for absorption. First principle calculations were performed using ‘Quantum Wise Atomistic Toolkit’ package with Perdew-Burke-Ernzerhof (PBE) exchange-correlation for black phosphorus doped with non-metallic dopants of B, S and Se and metallic dopants of Ti, Mg and In. It has been found that doping with non-metallic impurities result in a small diminution of the band edges (0.96–0.57 eV), whereas doping with metallic impurities decrease the band edge drastically (0.85–0.025 eV). Moreover, it was also observed that dopants with an even number of valence electrons incorporated a metallic nature of black phosphorus, whereas dopants with odd number of valence electrons further attributed to its semiconducting features. Thus in a holistic discernment, black phosphorus with the incorporation of some dopants in appropriate amounts can absorb more visible range of the optical spectra, making it ideal for use in photovoltaics.

Mar 1, 2017

By Dexter G. Mendoza

To analyze the behavior of minor elements in the copper smelting process, the phase relations and the activities of arsenic and antimony in the miscibility gap of Cu-Fe-S-X (X = As or Sb) system have been determined at 1473K by the quenching method and the double Knudsen cell- mass spectrometric method, respectively. The experiments have been conducted for the charges in the miscibility gap with different mass%Fe/mass%Cu ratios with varying arsenic or antimony content. The activity measurements indicate that the arsenic activities in both the metal and matte phases show extremely negative deviation from the ideal behavior. The Raoultian activity coefficients at infinite dilution in the metal and matte phases are found to be almost constant against the charges in the miscibility gap, and they are 4.3 x 10-3 and 5.5 x 10-2 for the metal and matte phases, respectively. Moreover, the activity measurements of antimony show an activity value larger than that of arsenic but it still deviates negatively from Raoult's law. The activity coefficients of antimony at infinite dilution are found to be 1.2 x and 2.2 x 10-1 for the metal and matte phases, respectively. The vapor pressures of the predominant As, AS2, AsS, Sb, Sb2, and SbS species in the gas phases of arsenic and antimony, respectively, equilibrated with the immiscible solutions have been calculated on the basis of the determined activity coefficients and they are very small at less than 1 Pa, even when their contents in the metal phase are increased up to 10 mass%.

Jan 1, 2002

By C. M. Acuña

Copper losses in slags are of great concern, specially in smelting and slag cleaning processes. It is widely accepted that the suspension of metallic copper and matte droplets is strongly affected by the viscosity of the slag. The Chuquicamata Division of Codelco- Chile produces concentrates high in zinc, an element which reports mainly to the slag phase. The ZnO may affect the viscosity and therefore the copper losses. This work aimed to investigate the effect of lime to control the viscosity of slags, and in turn to control the copper losses. By using the experimental viscosity data and the Stoke's law, the settling rate of matte prills in various slags was estimated. The results indicate the possibility of increasing the recovery of copper and/or decrease the process time.

Jan 1, 1999

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By Liangying Wen, Jian Xu, Dongdong Wang, Kaihui Ma, Yang Xu

Slags play an important role in blast furnace operation, and their com- positions are based on the CaO –SiO2–MgO–Al2O3 quaternary system. However, there is not a clear understanding of the effects of gangue on of the formation of FeO-bearing primary-slags process in blast furnace. In this work, the softening and dripping experiments under the blast furnace conditions are designed to explore the influences of CaO-/SiO 2-/MgO-/Al2O3 on the softening and melting properties of FeO respectively. The results indicate that additions of CaO or Al2O3 decrease the starting softening temperature and no dripping behaviors are found in comparison with the base case results when only FeO is used. On the contrary, the addition of SiO2 or MgO rises the starting and ending softening temperature, as well as the dripping temperature. The lowest maximum pressure drop is obtained in the case with addition of SiO2. According to XRD analysis results, the initial phase with CaO addition in the primary-slags should be CaOFe3O4 and that with SiO2, MgO, Al2O3 additions are fayalite (2FeOSiO2), magnesioferrite (MgOFeO), hercynite (FeO2Al2O3), respectively.

Mar 1, 2017

By A. V. Tarasov

Emission of sulfur-containing gases causes most adverse impact on the natural environment in the process of nonferrous metals production. Under the conditions of Arctic regions, in particular in the region of the Norilsk Mining and Metallurgical Complex (Russia), this problem requires a special approach taking into account potential economic and socioeconomic consequences. By reducing the iron sulfide content of flotation concentrates by using new flotation reagents inhibiting pyrrhotite flotation and by applying advanced process flowsheets for flotation it is possible to increase the nonferrous metals content of flotation concentrates by 5% or more along with a corresponding reduction in SO2 formation during their subsequent pyrometallurgical processing. The ways used to resolve the environmental problems in the Norilsk region in the process of nickel and copper production, are based on the improvement of methods for elemental sulfur recovery from metallurgical off-gas by non-conventional techniques, the sulfur recovery from metallurgical gases by production of liquid sulfur dioxide and the technology for pyrometallurgical treatment of sulfide concentrates without SO2 formation. Another opportunity is the development and commercial introduction of hydrometallurgical technologies for treating copper-nickel sulfide ores.

Jan 1, 2006

By M. A. Barron, D. Y. Medina, R. T. Hernandez, I. Hilerio

"Chromium Nitride (CrN) thin fihns were deposited on steel AISI 316 substrates with reactive magnetron sputtering method. CrN films were produced under two different conditions. In the first one, the substrate was heated by a d.c. source. At the second coating was applied a negative substrate bias voltage. X ray diffraction, quantitative energy dispersive and scanning electron microscope, were employed to characterize their phases, chemical composition and microstructure. Additionally microhardness was evaluated using a microhardness tester. The results show that the phase formation of CrN thin films in the first case (with temperature) is better. Both coatings presented homogeneous surface. Their compositions shows differences though that gases flow are same. In attention to their hardness, presents an increment if it's compared with hardness substrate.Nomenclature.P Ar =Argon gas pressure during coating.PN2 = Nitrogen gas pressure during coating.Ts = Substrate temperature during coating.T f = Coating melting temperature. (CrN = 1050°C).E=Potential difference.t =Coating time.P=Target power (Cr) in magnetron sputtering de.HV = Vickers hardness.F = Applied charge.d= Average length of longitude of the two diagonals (mm)Introduction.Wear causes losses in materials surface, generating that components of mechanical systems suffer irreversible changes in their properties, causing a faulty operation of the system. It is important to control their effects, measuring and interpreting their causes clearly."

Jan 1, 2013

By I. M. Richardson, M. Janssen, W. Geerstma, I. J. Bennett, V. A. Popovich

Avoiding wafer breakage is a big challenge in the photovoltaic silicon industry, limiting production yield and further price reduction. Special fracture strength tests suitable for thin silicon solar wafers and solar cells, to be used in combination with Weibull statistics, finiteelement (FE) modelling and digital image correlation have been developed in order to study the mechanical stability of solar wafers. The results show that removal of the saw damage significantly increases the strength of crystalline silicon wafers. Furthermore, it was found that silicon crystallinity and the location where the wafer is extracted from the cast Si ingot have a significant effect on the strength, namely samples taken from the bottom of the ingot are 30% stronger than those taken from the top. The study also showed that there is a decrease in fracture strength when an anti-reflective SiNx coating is applied, which is caused by high thermal stresses.

Jan 1, 2015

By Larry Southwick

In the early 1940's, the Caron ammonia ? ammonia carbonate leach process was used to produce nickel from Mayari ores at the Nicaro plant in Oriente Province, Cuba. While plant operation was generally successful, it was not broadly economical and was shut down. The plant was later restarted in the 1950's and a number of investigations initiated to resolve the more serious operational and performance issues. Processing steps studied included iron reduction (chemistry ? nickel and iron, reductant, equipment), ore variability (homogeneity and consistency of mineral concentrations, serpentine vs. laterite), leach solution strength, nickel recovery (temperature ? reduction and leaching, reoxidation) and a variety of other topics. These studies and their findings will be discussed. Caron himself obtained good results on these ores in the laboratory. They could not be duplicated in the field, the reasons for which will be reviewed. (Note: the ore looked like garden dirt; charcoal made from palm trees was one of the reductants attempted; and ammonia was the leach solution. Mixing the three, so to speak, was to yield nickel.)

Jan 1, 2006

By Stanko Nikolic

Ferrous calcium silicate slags are potentially important for future practice in copper converting operations and processes and can be described by the ?Cu2O?-FeO-Fe2O3-CaO-SiO2 system. Despite its industrial importance the phase equilibria in this system have not been fully investigated. Characterization of this slag system is necessary to improve the design and optimization parameters of new processes, including fluxing and operating temperatures. Experimental methods have been developed to investigate the phase equilibria of these slags at copper saturation and without copper. This technique involved equilibration of samples at a fixed oxygen partial pressure, rapid quenching, and analysis of the compositions of phases using electron probe x-ray microanalysis (EPMA). Liquidus and solidus data are reported for the primary phase fields of spinel, wollastonite and tridymite at 1250oC and an oxygen partial pressure of 10-6atm. The resulting data has been used to construct liquidus isotherms in the ?FeO?-CaO-SiO2 system both in equilibrium with and without molten copper. The experimental results were compared with the predictions of a thermodynamic computer package utilizing a self consistent thermodynamic database. The predictions of the model were in good agreement with the experimental isotherms when projected onto the FeO-CaO-SiO2 section, however the copper concentrations in the liquid phase at copper saturation were lower than predicted using the current database of the model.

Jan 1, 2006

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By Alexander V. Suvorin, Vladyslav M. Sokolov

"The traditional technologies for production of the coprecipitated and deposited catalysts are analyzed from the standpoint of diversion of application of the feedstock and increase of efficiency for its usage. The options for return of the metals of spent catalysts to the catalysts production are described. The novel environmentally friendly and cost efficient approach for reutilization of the spent catalysts is realized in practice. It anticipates application along with spent catalysts of the waste generated in the catalytic productions. Reutilization of the Ni-containing catalysts is referred as an illustration. Introduction The recent development of large catalytic manufacturing for organic and inorganic synthesis, and petroleum refinery as well as for applied environmental catalysis has brought about increase and diversification of catalysts production. The generation of spent catalysts has been increased correspondently. The feedstock for production of catalysts is mostly metals in a form of nitrates, carbonates, hydroxides, hydroxydcarbonates. Sometimes salts of organic acids, of ammoniates, of chlorides and of sulphates occur. All these materials are scarce and expensive. So their repeated use by reutilization of spent catalysts is very actual issue. The traditional recycling the Fe-, Cr-, Ni-, Cu- or Zn-containing spent catalysts are carried out by pyrometallurgical reclamation of pure metals or alloys. They can not be used directly in production of catalysts [1, 2]. The hydrometallurgical approach is used for recycling spent catalysts with PGM, W, Mo, Co, Ni or Cu. It provides production of salts of these metals in a form of sulphates, chlorides, carbonates, hydroxydcarbonates and sometimes nitrates or ammoniates. Only a limited number of these salts can be used directly in production of catalysts. Material losses during catalysts production The basic feedstock for manufacturing coprecipitated and deposited catalysts that may be produced from the spent catalysts is aqueous solutions of metals nitrates. Their production is based on application of nitric acid as a dissolvent. About half of it is lost with the flue gases in a form of nitrates vapor and nitrogen oxides (II, IV). The last compound is generated by reaction:"

Jan 1, 2008

By Jillian Spindura

This work investigates the carbothermic reduction of the complex sulphide mineral, pentlandite, in the presence of lime. The effects of change in temperature and the use of different carbon sources are studied and the role of these variables on the reducibility of pentlandite mineral is discussed. The microstructures of the heat-treated pellets are examined using X-ray diffraction and scanning electron microscopic techniques. The latter analytical method also allows any variation in the morphology and composition of the metallic phases formed, with temperature, to be considered. The kinetics of the reduction process is studied and the magnitude of the overall activation energy is determined from the plots of percentage reduction versus time.

Jan 1, 1996

By R. E. Burleigh

'Gold-telluride mineralization was deposited in quartz veins which cut a Late Cretaceous tonalite pluton emplaced near the southern margin of the Peninsular tectono-stratigraphic terrane in south-central Alaska. The gold-bearing veins formed shortly after the development of a widespread Cu-Mo sheeted quartz vein system. Early mineral assemblages consist of quartz, white mica, pyrite, and arsenopyrite (wall rock only). Subsequently, pyrite. sphalerite, chalcopyrite, zoned tetrahedrite and gold precipitated within multiply fractured veins. Late stage galena, tellurides (altaite, nagyagite, coloradoite), and Pb-Sb or Pb-Cu-Bi sulfosalta with gold constitute bonanza ore assemblages that are variably associated with quartz, white mica, ankerite, and calcite. Fluid inclusion evidence coupled with mineral assemblage paragenesis suggests the depletion of volatiles (C02, H2S) and cooling resulted in the precipitation of high grade gold mineral assemblages.

Jan 1, 1988

By J. P. Bellot

During the non-ferrous metal processing, the melting step under vacuum or under rarefied gas leads to volatile metal losses. It is the case of the metallurgical processing of the nickel-based, titanium-based or zirconium-based alloys where the evaporation losses don't allow a sufficient control of the alloy chemical composition. A theoretical approach has been carried out involving both a continuum description in the liquid phase and a molecular approach in the rarefied gas phase. The finite volume method is used in order to solve the coupled transport equationsin the liquid, whereas the Boltzmann equation is modelled by using a Monte Carlo method. At the liquid metal and metallic vapor interface, the volatilization and recondensation fluxes link up the two calculations. Simulation results are given for the melting and refining of reactive metals such as titanium alloys where the control of the chemical composition remains a major difficulty. The validity of the kinetic Langmuir's law is discussed for different operating conditions.

Jan 1, 1996

By ChuanJie Cai, Zemin Zhuang, Jing Chen, Xuebin Hao, Shaobo Zheng

"Carbon which was used as heating and reducing agent in traditional iron and steel making process at present brought us large amounts of greenhouse gas harmful gases and dust seriously leading to the fog and haze condition. As one of ideal global new energies, Hydrogen has good features such as rich resource, high heat efficiency, cleanness, renewable and transportation. With the commercialization of hydrogen energy, the world energy structure will be changed greatly. Although many scholars have done a lot of researches and long-term exploration on hydrogen metallurgy, researches on the formation of metal iron phase in the process of hydrogen reduction of iron oxides in slag was rarely reported, which had important theoretical significance on the development of hydrogen smelting reduction process. Based on the thermodynamics and kinetics calculation, A laboratory experiment has been designed to research the iron phase formation during hydrogen reduction of iron oxides in the molten slag in this paper. SEM and EDS techniques were also used to observe and analyze the iron morphology. According to detection results, the influence of temperature, reaction time and surface tension on the morphology of the iron phase reduced were showed.IntroductionWith the increasingly severe global warming greenhouse effect, governments are paying more attention to no-carbon and low-carbon energy development and utilization. Hydrogen has received widespread attention around the world, which has rich resources, high thermal efficiency, large energy density, use clean, transportation, storage, renewable etc [1].The development of the hydrogen economy is new competition areas of the world economy for the 21st century. China should assess the situation, and achieve the important strategy of peaceful development as the realization of new industrialization, by establishing a ""hydrogen economy"" industry revolution which replaces fossil energy. The current hydrogen metallurgy process includes hydrogen direct reduction, smelting reduction and direct steelmaking process. Hydrogen plasma hydrogen metallurgy is the use of hydrogen as a reducing agent to replace carbon reductant, to reduce carbon dioxide emissions, and to ensure the sustainable development of ironmaking industry."

Jan 1, 2014

By Bing Ji Yan, Cui Wang, Ya Peng Zhang, Chuan Hui Li, Hong Wei Guo, Jian Liang Zhang

There are a lot of research of the chlorine element’s influence on blast furnace, and mainly pay close attention to the harm to gas pipes and equipment. There are three kinds of chloride in the blast furnace gas, including HCl, NH4Cl, and NaCl (or KCl, ZnCl, etc.). This paper mainly analyzes all kinds of phenomenon of the chlorine element overflowing blast furnaces in Jinan Steel, and puts forward some different viewpoints, which are that the chloride overflowing out of blast furnace in the types of HCl, NH4Cl, or NaCl (KCl) not only has much to do with raw materials of chlorine load level, at the same time with the blast furnace burden distribution. On this basis, comes up with countermeasures for the different situation, such as adjusting the burden distribution matrix to guarantee the central gas flow smooth and changing the kind of raw materials to reduce the chlorine quantity, which will be helpful to prevent the harmful influence of chlorine element.

Mar 1, 2017