Search Documents

By Yongxiang Yang, Yanping Xiao, Robert G. Harskamp

"Stricter environmental regulations demand for safer treatment and disposal of incineratior fly ashes. So far no sound technology and processes are available for a sustainable and ecological treatment of the waste incineration ashes, and only partial treatment is practised for temporary and short-term solutions. New processes and technology need to be developed for comprehensive utilization and detoxification of the MSW (Municipal Solid Waste) incinerator residues. The objective of the current research is to better understand the behaviour of the environmental harmful elements during low or high temperature treatment, and to find an optimum route for an efficient processing of the incineration fly ash. In the present study, the fly ashes including boiler ash and ESP (Electrostatic Precipitator) ash sampled from a MSW incinerator were washed with warm water, and the residues were dried and sintered or vitrified at high temperatures. The solutions from ash washing were analysed, and will be treated for salt extraction and purification. The ash residues before and after thermal treatment were also analysed. The results of vitrification and thermal behaviour were compared with those from the ashes without pre-washing. It was found that water pre-washing is an efficient way to remove certain water-dissolvable volatile salts such as chlorides, and thus the secondary emissions during vitrification could be reduced. INTRODUCTION The air pollution control residues from MSW incineration are classified as harzardous waste, including boiler ash, ESP ash and filter cake. The boiler ash is the firstly settled flue dust in the dust-collecting equipment under the boiler, the ESP ash is collected by an electrostatic precipitator in the second step, finally the flue-gas is further cleaned by the wet-scrubbers and residues are accumulated in the filter cake. Both the boiler ash and ESP ash are classified as hazardous materials, harmful to the environment due to the high concentrations of environmental hazardous elements. However, due to the different locations of the ash collection, the boiler ash has different compositions compared to the ESP ash, and is considered less toxic. Fly ash is generally toxic and with low bulk density, and has to be treated before final disposal. The current industrial practice is normally the landfilling after partial detoxification such as cement solidification."

Jan 1, 2008

By Dirce H. Jacomo, Jaciele G. Teixeira, Anibal Y. Abreu Castillo, EsperidianaA. B. Moura, Yalquiria A. Silva, Rene R. Oliveira, Michelle G. Gomes

"Composites consisting of poly(vinyl alcohol), starch and sugarcane bagasse ashes, using glycerol as plasticizer agent, were prepared by solution casting method. Composites prepared were subjected to electron-beam radiation treatments, at radiation dose of 50 and 80 kGy using a Dynamitron electron beam accelerator, at room temperature in the presence of air. The composite samples obtained were evaluated for their water absorption, mechanical and morphological properties.1. IntroductionThe potential of biodegradable polymers and more specifically of biocomposites obtained from agro-resources have long been well established [1-3]. Starch, derivate from variety of botanical sources (cereals, legumes, and tubers) is widely available raw material and one of the most studied and promising agro-resources for the production of biodegradable polymers as matrices for biocomposite applications. However, starch itself is very brittle, hydrophilic and its mechanical properties are very poor for many applications [3 - 5]. The blending of starch with conventional polymers is a promising approach to improve its drawbacks. Recently, many efforts have been made to blend starch with biodegradable synthetic polymers [5, 6]. Polyvinyl alcohol (PYA) is a particularly well-suited synthetic polymer for the formulation of blends with natural polymers, as it is highly polar and can also be manipulated in water solutions, and depending upon its grade, in functional organic solvents as well [3, 7]. PY A has been reported to be an option to blend with starch. Most of the starch/PY A composites have been prepared by casting. However, it is well known that starch/PY A composites has poor in water resistance and mechanical properties after absorbing water [3,8]. Attempts to improve the mechanical properties and to decrease the water absorption property of the starch/PY A composites are made by adding the cross-linkers and plasticizers. Park et al. prepared starch/PY A/citric acid films by the casting method. They also studied the effect of (spell out) citric acid on the mechanical properties and water resistance of composites [9]. Zhai et al. prepared the starch/PY A hydrogels using electron-beam radiation [10]. Different kinds of lignocellulosic fibers have been investigated in blends for formulation of biocomposites."

Jan 1, 2013

By A. E. M. Warner

Inco Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By Cyro Takano

This paper is a contribution to fundamentals data on the equilibrium metal/slag for refining silicon in relation to Ca and Al as impurities. Silicon containing 0.1% Al and no Ca was placed in contact with a slag of various contents of CaO, SiO2 and Al2O3. Slag Al2O3 contents were 11.4%, 25.1% and 29.6%, keeping the ratio %CaO/%SiO2 constant and equal to ~0.53. The experiments were conducted at 1550oC, in a graphite crucible with argon atmosphere. The equilibrium was observed with low and medium content of Al2O3. The derived activities coefficients of Ca and Al in dilute solution of Si presented good correlation with those of the literature. Parallel reactions with formations of SiO(g) and CO (g) were also observed.

Jan 1, 2006

By Kenji Monden

"In order to obtain basic data for the development of highly thermally conductive composite materials, the thermal conductivity of a resin composite material with an Aluminum Nitride filler was assessed. Several different measurement techniques such as the xenon flash and the temperature wave thermometric analysis method were employed to gather data on these composites. An excellent match between theoretical and experimental data was achieved by employing a predictive expression that takes into account the effect of percolation on thermal conductivity.IntroductionA thermal solution composite is made by incorporating dense inorganic fillers with high thermal conductivity into a resin. Because the composite materials have high thermal conductivities, they have been used in electrical products that generate excessive thermal energy during operation, such as inverters, amplifiers and motor drivers. They function as electrically insulating and thermally conducting parts of the electric modules. As the uses of thermal solutions are expanded, composites of higher thermal conductivities will be required. The aim of this work was to investigate, evaluate, and try to predict the influence of key parameters on thermal conductivity and diffusivity. This was achieved by analyzing the effect of both volume fraction and shape of Aluminum Nitride ceramic fillers and measuring the thermal conductivity. In addition, the influence of percolation on thermal conductivity is considered. The thermal conductivity of the composites is discussed by employing a predictive equation using literature data of thermal conductivities for both the filler and resin. As well as thermal conductivity measurements the effect of volume fraction of the filler was also explored.ExperimentalSpecimen PreparationThe composite samples were prepared from silicone resin and Aluminum Nitride (AlN) fillers. The AlN fillers with an average particle size of 20 µm are shown in Figure 1. The mean diameters of the AlN particles used are given in Table I. For comparison the AlN fillers with an average particle size of 5 µm are shown in Figure 2. A planetary centrifugal mixer was used for simultaneously dispersing the components uniformly and de-aerating the mixture. After mixing, these materials were placed in a silicone rubber case and cured at 150 °C for 1 hour."

Jan 1, 2013

By Oluwatosin A. Aladejebi, Apsara S. Jayasekara, Raymond J. Longbottom, Mark Reid, Marc in het Panhuis, Brian J. Monaghan

The coke analogue is a new research tool that has been developed to quantify and characterize the effect minerals in coke have on coke reactivity. The analogue material is made from a number of different carbon or carbon containing materials and minerals to in part replicate real industrial coke’s reactivity behavior. Elucidation of the effects of minerals on coke reactivity has proved difficult due to the complex and heterogeneous nature of industrial coke and the potential non-additive effects of minerals on coke reactivity. The coke analogue addresses this complexity and heterogeneity through control of its mineralogy, mineral size and mineral dispersion through the analogue, porosity and carbon structures. Initial studies using the analogue were focused on coke dissolution kinetics in liquid iron but recent work has focused in characterization of its porosity, carbon structure and rate of reaction.

Jan 1, 2014

By I. E. A. Aghachi

During static strain-aging of low carbon steel, when the material is pre-strained, the dislocation density increases. If totally or partially unloaded and aged for a prescribed time, interstitial solute atoms diffuse under the influence of the dislocation stress fields, thus tending to lock dislocations causing an increase in yield stress. If held for long periods at certain aging temperature, a decrease in yield stress (over-aging) is observed following the initial increase. This behaviour has been variously attributed to either recovery of cold worked dislocation structure and/or formation and coarsening of carbide precipitates. The present work demonstrates that, using a "process control" model for the competing processes of hardening and softening, dislocation recovery is responsible for over-aging of mild steel specimens under conditions tested during this investigation. Keywords: Strain-aging, Precipitation, Recovery

Jan 1, 2003

By Peter A. Spencer

Bacterial oxidation technology has the ability to selectively attack sulphide minerals. Selectivity allows oxidation of more reactive minerals and the extraction of valuable metals while leaving the bulk of the sulphide component unreacted. Partial oxidation can be used on arsenopyrite to recover gold and for the leaching of base metals, such as copper and nickel, from pyritic ore and concentrate without generation of large quantities of acidic iron solution, which must be neutralized. Thus, rejection of pyrite during the oxidation process can considerably reduce treatment costs. Acid generation in tailings dams would be minimal, compared with most Thiobacillus cultures, as the optimum growth temperature of Bactechts culture is above ambient.

Jan 1, 1992

By A. C. Cascalheira, L. M. Abrantes, M. Savic

This paper reports our results on the application of a novel process for the spontaneous and sustained reduction and recovery of elemental silver and gold on an electroactive polymer surface. This work incorporates the metal recovery from photographic films (silver) and goldsmith residues (gold), by direct contact of metal containing solutions with polymer. The performance on such process of electrochemically and chemically prepared polyaniline (P ANI) is evaluated. SEM coupled with EDX and XRD analyses confirmed the presence of metallic silver and gold deposited onto polymeric material.

Jan 1, 2000

By Mrutyunjay Panigrahi, Takashi Nakamura, Atsushi Iizuka, Etsuro Shibata

"The production of FeTi intermetallic alloys from mixed oxide precursors using direct electrolytic reduction was studied. Fe203 and Ti02 powders were mixed in appropriate molar ratios, pressed into small pellets, and then heat treated at temperatures in the range 1000-1300°C. The pellet heat treated at 1000°C was electrolyzed in molten CaCh at 950°C, using a graphite crucible as the anode and the oxide pellet as the cathode, at a potential of 3.0 V. The products of the electrolytic reduction of (Fe,Ti) oxide were examined by XRD, SEM and EPMA. It was found mat the (Fe,Ti) oxide was reduced progressively from the outside to the inside of the pellet until the metallic state was achieved.IntroductionFast and energy-efficient technologies for materials production are essential for the sustainable development of society, and such development is supported by advanced technologies. Since the introduction of titanium and titanium alloys in the early 1950s, these materials have, in a relatively short time, become major materials for the steel, aerospace, energy, and chemical industries. Its combination of a high strength-to-weight ratio and excellent mechanical properties and corrosion resistance make titanium the best material for many critical applications [1]. Titanium alloys are now used in demanding applications such as static and rotating gas-turbine engine components. Some of the most critical and highly stressed civilian and military airframe parts are made of titanium alloys. The use of titanium has expanded in recent years to include applications in nuclear power plants, oil-refinery heat-exchangers, marine components and medical prostheses.Ferrotitanium is one of the most widespread and effective ferroalloys. It is also a well-known hydrogen-storage material and will be extensively used in the future because hydrogen is emerging as an eco-friendly energy source [2], Ferrotitanium is an alloy consisting of iron and titanium, with a minimum titanium weight content of 20% and a maximum titanium weight content of 75%, and is manufactured by reduction or melting."

Jan 1, 2012

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By J. N. Hryn, E. J. Daniels, M. Askew, Kirchner. G.

This presentation addresses the changing regulatory climate towards aluminum dross and salt cake in Europe and in the United States. Although sporadic, the trend in the U.S. continues to be away from command-and-control regulation of these materials. This trend began in the early 1980s when the Environmental Protection Agency was successfully sued in court and prevented from classifying dross as a hazardous material. The situation in Europe is different. Because of Council Directive 96/61/EC from the European Commission, European Union member countries have all passed legislation that will essentially cause all salt cake and drosses to be reprocessed. The implementation date of the legislation varies from country to country: from 2001 in the United Kingdom to 2007 in Germany, France, Austria, Italy, and Spain. The European aluminum industry is urging the EC to use the approach adopted by the U.S. EPA, which declassifies the majority of aluminum drosses and salt cakes.

Jan 1, 2000

By Hongbo Zhu, Jinhui Peng, Linqing Dai

"To optimize the process variables for making direct reduced iron (DRI) by microwave heating, the reduction temperature, reduction time and the ratio of coal to material were studied with the central composite design (CCD) and their interactions on the Metallization rate were also investigated. The predictive polynomial quadratic equations model was analyzed by ANOVA. Optimal conditions of making DRI can be concluded as follows: 28 min at 1139?, the ratio of coal to material is 20.95%. Under these conditions, the metallization rate is up to 97.06%.1. IntroductionThere are some technical problems in making direct reduced iron (DRI) or sponge iron using iron ore concentrates containing coal and lime. In reduction of the iron ore concentrates containing coal with microwave heating, the strength of pellets needn’t to be considered. It reduces the costs and improve quality of materials, but also eliminates the need for pellet preparation process, simplifying the process and achieving a cleaner production.Microwave energy is a clean energy, and has characteristic of selective heating. The speed of heating is also fast. It researched by Chen Jin that when the mole mass of C: O is 0.627 and the microwave power is 15KW, it only spends 15min from 15? to 1021.6? with 1 kg iron ore containing coal with microwave heating [1]. There are many factors affecting metallization rate. In order to find a suitable condition for reduction process, it is necessary to design a series of suitable experiments.Response surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [2–5]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the identification of the vital controllable factors to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected. The process optimization of the microwave reduced iron ore was seldom reported in literature. Hence the present work intends to assess the effects of variables such as reduction time, reduction temperature and the ratio of coal to identify the optimum conditions using a central composite design (CCD). The characteristic of product was assessed using scanning electron microscope (SEM)."

Jan 1, 2011

By Baokuan Li, Qiang Wang, Zhu He

"A mathematical model has been developed to investigate the magnetohydrodynamic (MHD), thermal, and solidified behavior in electroslag remelting process. Based on the finite volume method, a multiphase coupling MHD approach is employed to investigate the droplet formation as well as movement in molten slag under the action of an alternating current. The VOF formulation is adopted for interface tracking. The electrical potential method is adopted for the electric current and magnetic field. The Electromagnetic force and Joule heating are recalculated at each time step and then is implemented in the momentum and energy equations as a source term, respectively. Moreover, solidification of the metal is described by an enthalpy-based formulation, while the mushy zone is treated as a porous medium with porosity equal to the liquid fraction. The model is used to investigate the effect of electrode tip shape on MHD, thermal, and solidified behavior and provide valuable information.IntroductionElectroslag remelting (ESR) process has been used widely to produce high-performance alloys dedicated to critical application, such as hot work tool steels, nickel base alloys, the manufacture of components in aerospace and landbased turbines, etc. Figure 1 shows a schematic diagram of ESR process including a consumable electrode, a molten slag pool, a liquid metal pool, a solidified ingot, and a water-cooled mold. Alternating or direct current flows from the electrode to the water-cooled baseplate through the high resistivity calcium-fluoride-based molten slag which result in Joule heating and Electromagnetic force (EMF). Part of the Joule heating melts the electrode and the droplets travel through the slag and accumulate the liquid metal pool. The electrode is continuously advanced into the slag as it melts to build up an ingot of improved structure and composition by controlled solidification and chemical refinement. The metallurgical properties of the remelted ingot are really related to the solidification structure, which strongly depends on magnetohydrodynamic, thermal, and solidified behavior in the molten slag, liquid metal pool, and mushy zone."

Jan 1, 2014

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Ho Jung Heo

The proper control of slag composition is a dominant factor affecting yield of iron as well as dephosphorization efficiency in an electric arc furnace (EAF) operation. Moreover, thermophysical properties of slags such as viscosity are strongly affected by the changes in slag composition. Slag foaming, which is also a function of viscosity, is directly connected with the yield of iron and thus optimum slag chemistry are highly required in view of thermodynamics and physical properties. Therefore, we analyzed the slag composition in commercial melt shop (70 ton EAF) with the aim of higher yield of iron as well as higher dephosphorization during EAF process.

By James P. Bennett

EAF slag chemistry and its control have been recognized as important in producing quality steel at a low price for a number of decades_ EAF steel producers make lime and dolomite additions to furnaces, controlling the CIS ratios and sulfur pickup from the steel. Existing phase diagram data at 1600°C for CaO, MgO, FeO, SiO2, and Al2O3 was used to write a computer model optimizing slag chemistry for slag foaming and reduced refractory wear. The model, its development, and its use in an industrial steelmaking environment will be discussed along with how the model can improve energy efficiency. The importance of EAF mass balance to account for critical materials like Si in scrap and refractory wear using the model will also be emphasized_

Jan 1, 2003

By Nobuaki Sato

For decontamination of SO2 containing waste gases from industries such as ferrous and non-ferrous metal companies, desulfurization with hydrogen production by the reaction of Br2 and SO2 was proposed as bromine-sulfur (BS) process. In this process, SO2 is fixed as H2SO4 in the presence of Br2 and H2O forming H2SO4 and HBr. Then hydrogen is produced by the decomposition of HBr and Br2 as byproduct is recycled. The reaction of Br2, SO2 and H2O was found not to occur in liquid phase but to occur in vapor one. The production ratios of H2SO4 and HBr showed a maximum at temperatures around 60 oC. The highest production ratio was obtained at 70 oC with a mixing ratio of Br2:SO2:H2O=1:1:10. The experimental results were discussed with thermodynamic consideration.

Jan 1, 2006

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008