Search Documents

By K. Hussin

Perlis is one of the major producers of ?Batu Reput? in Malaysia and majority of the deposits contain of high-purity calcium and magnesium carbonate. The composition of Batu Reput is similar with the ordinary dolomite. Currently, the ?Batu Reput? is used as filler in the road construction, however with this new invention, it can be value added and maximized its application in the daily life, for example as construction materials, decorative products, souvenir and etc. This paper presents the fabrication of Artificial Marble from ?Batu Reput? and in this case, it was used as filler in the matrix of epoxy which is acted as a binder.

Jan 1, 2006

A full-scale test of chalcocite heap bioleaching was undertaken at Straits? Nifty Copper Operation. Straits worked closely with the CSIRO to investigate the chemical and biological changes over the life cycle of this chalcocite heap bioleach system. Results indicated nearly 80% copper recovery was achieved in just over 300 days. Significant changes in iron chemistry and microbiological activity were detected. Temperatures in the heap reached as high as 70 ºC during the time of maximal copper recovery rate. The dominant cultivatable bacterial strains were typical mesophilic bacteria, however, naturally occurring moderately thermophilic bacteria were detected by culture and culture independent molecular (PCR followed by denaturing gradient electrophoresis [DGGE]) and signature lipid methods. Signatures for the iron and sulfur-oxidising species Acidithiobacillus ferrooxidans and Sulfobacillus spp., as well as the moderately thermophilic heterotroph Alicyclobacillus sp. were detected. Biomass was greatest in ?warm? but not ?hot? parts of the heap, and Hyperthermophilic Archaea were not detected.

Jan 1, 2003

By V. Jiricny

The novel spouted-bed electrode (SBE) is a cathode system where copper is deposited at a high current density in a moving bed of copper particles. Preliminary results on the deposition of copper from acidic sulfate electrolytes using this novel cathode system were described during Copper '95 conference. Despite a high current density, the electrical energy consumption was equal to or lower than that in the conventional electrowinning. The present paper describes more investigations on SBE. The SBE consists of copper particles with approximately 1 mm diameter onto which copper is deposited from acidic sulfate electrolyte whose composition is similar to conventional electrowinning. Three types of anodes were used in conjunction with the spouted-bed cathode, namely, DSA anode for oxygen evolution, and two novel anodes. One anode is less expensive than DSA; however it showed much promise in energy consumption. At a superficial current density of 2200 A/m2, the energy consumption was around 1.0 kWh/kg copper. The research activities described in this paper were supported by BHP Copper.

Jan 1, 1999

By L. A. Kazanbayev

The Chelyabinsk Electrolytic Zinc Plant (CEZP) was commissioned in 1935. Over the elapsed years the Plant capacity has been increased from 10 thousand tons of zinc (1935) to 150 thousand tons of zinc (2005). The paper describes the Plant main achievements in production updating for the last 10 years.

Jan 1, 2006

By Mark E. Schlesinger

A substantial database exists for the thermodynamic properties of many antimonide compounds, but these have rarely been compiled or critically discussed. An abbreviated version of a full?scale review of the thermodynamic properties of binary antimonide compounds is presented, focusing on the choice of experimental techniques.

Jan 1, 2006

By Y. Prévost

The Noranda Continuous Converting Process was commissioned in November 1997 at the Home smelter in Rouyn-Noranda, Quebec, Canada. It has completed over 18 months of successful operation. Excellent team work and technical expertise contributed to achieve targeted production levels and environmental goals after only a few months of operation. The operating results have demonstrated the flexibility of the process in producing blister copper from a variety of copper feed materials including a combination of molten and solid copper matte, reverts and fluxes. This paper describes the startup activities and process optimization tasks performed during the first year of operation of the new Noranda Converter.

Jan 1, 1999

By Ross McClelland

This paper provides a technical overview on the installation and commissioning of the Ausmelt lead smelting, slag reduction and slag cleaning operations at the HZL Chanderiya site in India. It also discusses theoretical concepts behind the process practices currently in place at HZL.

Jan 1, 2006

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By Susumu Okabe

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace for settling the slag/matte mixture formed in the smelting furnace. In order to improve the separation of slag and matte and to minimize power consumption, the design and the operating conditions of the electric furnace should be optimized. As the first step, numerical heat and fluid flow analysis of the melts was carried out based on the distribution of current density and Joule?'s heat obtained by the electric field calculation. For these calculations, 3-D body fitted coordinate system and a finite volume method were applied. Using the developed numerical model, the flow pattern analysis by pulse input of a tracer element was simulated. It was found that a strong thermal convection of the molten slag exists around the electrodes due to the concentrated Joule's heat generation in a small area just under the electrodes, and this strongly affects the flow pattern in the furnace. The calculation results were compared with the data obtained from 'a plant test.

Jan 1, 1998

By Cam T. Nhan

The potential use of coal fly ash as a construction material has been recognized for many years,. In this work, an admixture of the ash residue is investigated for use as a landfill liner. In particular, its performance as a chemical barrier to the leachate from the municipal solid waste (MSW,) is determined. The test specimens are a water compacted admixture of class F fly ash, low in calcium content, which is blended with lime dust and calcium bentonite. MSW is passed through the compacted fly ash specimens under a gravitational head. The. diffusion of elements in the leachate through this material is monitored as a function of time. The distribution profiles of the retained elements in the compacted admixture provide prediction of the long term performance of the compacted admixture directly affect the leachate diffusion rate, hence, the mobilities of the retained elements.

Jan 1, 1992

By Shigehito Isobe

The Li-N-H system composed of LiH and LiNH2 catalyzed by titanium compound desorbs ~6 mass% hydrogen and a quite small amount of ammonia in temperature range from 150 to 250 °C under He flow atmosphere. In this work, hydrogen desorption (H-desorption) mechanism in the reaction from LiH+LiNH2 to Li2NH+H2 in a non-equilibrium condition was clarified by TDMS, TG and FT-IR analyses for the products replaced by LiD or LiND2 for LiH or LiNH2,respectively. The results suggested that H-desorption reaction progresses through two-step elementary reactions mediated by ammonia. As a next step, we carefully determined the amount of the ammonia containing in desorbed hydrogen for the Li-N-H system in a closed system from the practical point of view. The results indicated that a quite small of ammonia thermodynamically coexisted in the desorbed hydrogen in closed system, although ammonia could not be almost detected in emitted hydrogen gas by TDMS under some non-equilibrium conditions. Moreover, for understanding the role of titanium, the chemical bonding state of the titanium compounds doped as catalyst in the mixture was examined by XAFS measurement. The results indicate that the Ti atoms, which can induce catalytic effect, are in a particular chemical bonding state.

Jan 1, 2006

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-Si02 and FenO-MgO-CaO-Si02 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below 11 mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-Si02 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe304 on the viscosity was quite significant. The viscosity of slag increased by 300mPa's at l573K when Fe304 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-Si02 and FenO-MgO-CaO-Si02 systems is given in this study.

Jan 1, 2003

By Tetsuro Ohashi, Tooru Matsumiya, Yoshio Abe

"The three-dimensional deformation of a continuously cast slab was modeled into two-dimensional deformation by developing the solidified shell of the slab. The developed solidified shell was divided into rectangular elements. The thermal strain produced as the slab is wi thdrawn over one roll spacing in the casting direction was calculated from the temperature change during that time and the increment of the geometrical unbending strain during the time was calculated from the change in the radius of curvature of the slab by assuming that the neutral axis of bending is located at the mid-thickness of the slab and that the transverse section of the slab is kept in a plane during unbending. These strains were imparted to each element as initial strains. The interaction between the elements and the overall deformation of the solidified shell were analyzed by the finite element method.The analysis was performed on a slab being cast on a machine of the circular arc type with progressive unbending. The following findings were obtained as a result. The effect of unbending is spread in the upstream and downstream directions of the slab by the shear deformation of the narrow and wide faces. As the shear deformation increases, the strain in the unbending zone decreases and the strain outside of the unbending zone increases. The effects of secondary cooling conditions, slab size, radius of caster circular arc section, compression casting, etc., were also analyzed. IntroductionTo develop a method for preventing the internal cracking of continuously cast slabs, it is important to acurately analyze the deformation of the slab and this subject has been extensively investigated. Many researchers, including the present authors, have analyzed slab bulging. (1)- (11) Analysis has also been made of thermal deformation that assumes importance in continuous casting of small-section blooms.(12)-(18) However, unbending deformation, an extremely important subject for continuous casters of the circular arc type, has not been fully analyzed."

Jan 1, 1986

By Tarek M. Abd El Hamid, Suzane Ali

"Treatment of industrial waste materials is created serious problem in Egypt. Aluminium sludge is generated as a by-product from aluminium household industry which contains significantly high alumina content exceeding 90%. This by-product randomly disposed and creates serious environment problems to locate community. To develop the treatment process of this material, the recovery of high purity alumina and identify the potential application is being the primary objective, This paper represents the recovery process of alumina process waste sludge High purity alumina material <99.8% aluminium oxide with originate particle size 0.125-0.420mm and apparent density 0.39g/cm3 was obtained with a specific surface area 139m2/g. Alumina produced was modified by cerium oxide doped alumina. The catalytic activity and selectivity was investigated in conversion of iso-propanol via dehydrogenation reaction yielding only acetone indicating an excellent selectivity the dehydrogenation. The presence of 10% CeO2 increase in the catalytic activity of 82% for the originated alumina. Introduction Approximately 20 thousand tons of aluminium waste produced in Egypt in 2006 with increasing amounts expected in succeeding years. A part of this waste contains organics impurities which coexisted with aluminium waste as a result of manufacture final aluminium products, waste usually content <1 to 2 wt% of organic carbon. It's generally admitted that the organic species are present in the form of lubricant oils used in rolling and pressing equipments for aluminium sheet. Both industry and government face possible high-cost disposal problems that more magnified by large volume of waste produced. The alumina recovery leachable study conduct in this paper had the following objectives: 1- Develop a process that can provide an environmentally acceptable residue and also recover the available alumina. 2- Evaluate the alumina produced in terms of grade and catalytic application."

Jan 1, 2008

By Shengli Wu, Mingyin Kou, Feng Chang, Laixin Wang, Hua Lu, Jianliang Zhang

Sintering dust has been regarded as an important secondary resource in a modern steel plant. Sintering dust was mechanically treated using different milling machines and experimental conditions in air atmosphere. The changes in phase constitution, particle size, specific surface area, particle morphology, and lattice parameters of activated sintering dust were determined. It was found that the agglomeration of the particles take place during extended dry milling with accessible pores for Nitrogen gas. The maximum specific BET surface area in the stirring wet grinding and planetary wet grinding increases to 43.06 and 46.45 m2/g after activated 360 min respectively. With the increasing of energy input, the intensity of diffraction peaks of dolomite and hematite gradually decreased. Furthermore, the previous phase almost disappeared eventually under any experimental conditions. In addition, Fourier transform infrared spectroscopy indicates that organic matter and carbonate decompose easier than other phases, especially under stirring wet milling.

Jan 1, 2016

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By Yanhui Liu, Xuewei Lv, Pingsheng Lai, Chenguang Bai

The purpose of this paper is to study the effect of slag basicity on the Si content in stainless steel master alloys prepared by smelting reduction of Fe-Ni-Cr sinters. Theoretical analysis focusing on the gas, slag and alloy phases of the smelting reduction process at 1600°C was carried out by thermodynamic calculation software----FactSage, showing that the increase of CaO within the slag can result in the decrease of Si within the master alloy. Experiments were also carried out in vacuum melting furnace at 1600°C , and chemical analysis method was used to detect Si content in the alloys. When the MgO content is 9.00%, the experimental results were consistent with the calculated values. However, when the MgO content rises up to 14%, the content of Si in the alloy reaches the maximum when SiO2 equals to 22.81%.

Jan 1, 2016

By M. Benavides

An experimental study is carried out With sulphide ore obtained from Bailadores-Venezuela as well as artificial concentrates. Concentrates of the minerals from froth flotation are fused to study equilibrium between the matte and slag phases. The first part of the work deals with obtaining a concentrate by flotation experiments with collective and selective reagents, with acceptable metallurgical recovery, studying the influence of different parameters in the process. The second part gives the results of the experimental investigation. on thermodynamic equilibrium in smelting which facilitates knowledge of the elemental processes, giving bases for the possibilities of reducing the loss of metal in slag.

Jan 1, 1983

By G. J. Shiflet

This paper will review work done in our laboratory on the formation, thermodynamics and crystallization of aluminum based metallic glass with the addition of rare earth elements. The results demonstrate that the metallic glasses are truly amorphous and not microcrystalline and that they are unusual in their formation because the alloys contain 90 at. % aluminum and there is no deep eutectic present in the phase diagram. Tensile strengths that exceed 900 MPa are obtained for several of the compositions and exceed 1000 MPa after partial crystallization.

Jan 1, 1992