Search Documents

By Hong Ouyang

A unified computational model has been developed for the Bridgman growth processes of B-NiAI and CdTe crystals. To handle the geometrical and physical complexities, a two-level approach has been developed. At the gtobatlevel, conjugate heat transfer, phase change dynamics, and variable material properties along with the realistic geometries and thermal boundary conditions are accounted for inside the entire crystal growth system. Refined calculations are then made within the ampoule, with the boundary conditions supplied by the global simulations. This model can optimize the use of computational source, help understand solidification behaviors, and improve designs of crystal growth system.

Jan 1, 1996

By Rodney L. Williamson

Vacuum arc remelting (V AR) is an industrial metallurgical process widely used throughout the specialty metals industry to cast large alloy ingots. Part of the V AR control problem consists of adjusting arc current to control electrode melt rate which also depends on the electrode temperature distribution. Because the temperature distribution responds very slowly (1-4 hours depending on size and material) to changes in melt power, the melt rate response is history dependent and highly nonlinear. The situation is complicated further because measurement of the electrode temperature distribution is not practical. To solve the problem of accurate, responsive melt rate control. a low order electrode melting model has been developed and incorporated into a V AR process controller. Data from laboratory and industrial tests show that the goal of responsive, accurate melt rate control has been achieved, even when melting under highly dynamic process conditions. Keywords: Vacuum Arc Remelting. Model-Based Control

Jan 1, 2003

By P. Umadevi

In the light of the discovery of the new super-conducting YBa2Cu3O7-x (YBCO), reactions in the Y2O3¬CuO-BaO system at 1300°C was investigated. The search was for any new phase that may be formed in the system at 1300°C (only 950°C reactions are known so far). 35 mixtures of different compositions were prepared and heated at 1300°C. No new phase was obtained. It was found that YBCO is decomposed at this temperature and Y2O3 and BaCO3 are the major components in the solid obtained after firing in air. However, on cooling the melt slowly and annealing at 950°C YBCO reforms. Such reactions on cooling might have implications on processing of the superconductor YBCO for practical applications as well as on its crystal growth by flux method.

Jan 1, 1989

By Ross R. Bhappu

A theoretical and experimental investigation into pyrometallurgical refining of chloride leach/electrowin copper is described. The two techniques investigated were (i) vaporization and (ii) gaseous halogenation. Experiments were carried out with a packed bed of electrowon copper crystals and a boat of melted copper crystals. Nitrogen gas and Freon 12/nitrogen mixtures were used as the carrier and reac.tive gases. Vaporization was found to be effective in removing Bi, Pb and S while halogenation was effective. in removing As, Bi, Pb, S and Sb. Silver resisted all attempts at removal. Iron was removed but less effectively than the other impurities.

Jan 1, 1985

By Shadia J. Ikhmayies

Nanocrystalline CdS:In thin films with particle size in the range (3-36 nm) were produced by the spray pyrolysis technique on glass substrates. The films were characterized by investigating their X-ray diffractograms (XRD), scanning electron microscope images (SEM), transmittance curves and photoluminescence (PL) spectra. The size of the nanocrystallites was estimated from XRD difractograms and then from the hyperbolic band model and the bandgap energies of the nano- particles, which were calculated from the positions of the minima in the first derivative curve of the absorbance. Fine-structured PL spectra confirmed the nanocrystalline nature of the films.

Jan 1, 2010

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By Xiang Li, Merete Tangstad

Currently, the main carbonaceous material for Mn-alloys production is solid carbon, i.e. coke, charcoal and petroleum coke, which is produced with large CO2 emissions. Due to the simple purification, high carbon activity and low CO2 emissions, natural gas has some advantages compared with conventional reducing agents. The aim of the present project is to develop a new technology for production of Mn-alloys using natural gas as a source of carbon. Experimental results indicated that injection of CH4 gas directly into melted slag reduced slightly the MnO and SiO2. However, the metal yield was much less than the theoretical value due to a relative low residence time of CH4 in the slag. The alternative approach was to use carbon black as reductant, produced by CH4 decomposition. The preliminary experimental results showed a high reduction rate using carbon black.

Mar 1, 2017

By Senlin Xie, Wanlin Wang, Lejun Zhou

"The innovative development of multiphase slag in hot-metal treatment has attracted considerable attention due to the reduction of CaO consumption and minimal environmental emission. In order to improve the efficiency of dephosphorization and to reutilize the waste-slag as an alternative source of phosphate ores, it is important to increase the distribution ratio of P2Os between the solid solution (2CaO· SiO2-3CaO· P2O 5) and liquid slag. An investigation was carried out to study the effects ofNa2O and B2O3 on the distribution ratio of P2Os, the results indicated that the increase ofNa2O would enhance the distribution ratio of P2Os with the formation of solid solution (2CaO·SiO2-Na2O·2CaO·P2Os), while B2O3 has the opposite function, and changes the morphology of solid solution. The study would provide an instructive way for the design of multiphase slag and re-utilization of waste-slag.IntroductionIn order to meet the increasing demand for high quality low-phosphorus steel, it requires a high efficient hot metal dephosphorization process. The current slag system for hot metal treatment contains large amount of solid CaO dispersed in liquid slag, which introduced a large amount of CaO consumption due to its low solubility, especially when CaF2 was restricted due to the environmental concerns. Therefore, new refming method to improve the utilization efficiency of CaO by using a solid/liquid coexisting multiphase slag was proposed, and the studies regarding to solid solution formation mechanism, mass transfer behavior of phosphorus and the phase relationship for multi-phase slag have been conducted. [1-6]Normally, hot metal dephosphorization slag consists of CaO--SiOz-FeO--P2O 5, and it has been approved that 2CaO·SiO2 forms a solid solution with 3CaO·P2Os at the hot metal treatment temperature over a wide range of compositions. [7] Kitamura et al [8] pointed out that the (2CaO·SiO2-3CaO·P2O 5) solid solution plays an important role in dephosphorization, and it has been regarded as an absorbents for phosphorus to lower the phosphorus content in liquid phase, which makes it more capable for future dephosphorization. l Besides, the multiphase slag has the potential to be recycled as a source of phosphorus, if the (2CaO· SiO2-3CaO· P2O 5) solid solution could contain high phosphorus content, and it can be separated from FeiO matrix 8hase due to the large difference of their magnetic properties under the strong magnetic field. [10, 11]"

Jan 1, 2014

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated' cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By Henry L. Ehrlich

This survey compares bioleaching and biobeneficiation by autotrophic bacteria with that by heterotrophic bacteria and fungi Some physiological principles are reviewed. Advantages and disadvantages of autotrophic and heterotrophic leaching are discussed. Principles of anaerobic leaching by autotrophs and heterotrophs are introduced. and the advantages? over aerobic heterotrophic leaching are discussed. Examples of useful organisms in the autotrophic and heterotrophic categories are cited.

Jan 1, 1991

By Wei Han, Zhenwei Liu, Jianhong Yang, Qingwei Qin, Tiejun Chen, Zili Huang

The preparation of industrial ammonium molybdate from molybdenum concentrate was conducted according to the process of roasting—leaching—purification—precipitation—crystallization. The optimum technological conditions were determined: the roasting temperature was 680 degrees C, the roasting time was 2.5 h; in the leaching process the alkali excess coefficient was 1.2, the reaction temperature was 80 degrees C, the liquid-solid ratio was 3:1, the leaching time was 3 h; the amount of (NH4)2S added into the solution was 1.1 times of the theoretical amount, the temperature was 80-85 degrees C, and the terminal pH was 8.5-9 in the purification process; the density of the solution was 1.4-1.6 g/mL, the pH was 1.5-2 in the precipitation process; temperature of dissolution was controlled at 80-90 degrees C. The recovery of the preparation of ammonium molybdate can reach 85.18%.

Mar 1, 2017

By Ashwini Kumar

Flame impingement on the burden is routinely encountered during the initial phase of melting in aluminum reverberatory furnaces. This impingement causes an obstructed pathway for the hot gases, and hence the circulation and residence time of the hot gases are greatly impacted. Moreover, as the load melts, the flames gradually achieve an unobstructed path leading to reduced gas residence times. This flame impingement and constantly changing combustion space volume will lead to vastly different fuel and oxidizer mixing patterns and thus affect the overall furnace performance. Fine tuning the burner operating conditions such as flow rates and injection angles with the changing combustion space could result in significant improvements to the furnace efficiency. However, one has to gain a better understanding of the furnace dynamics to know the suitable parameters to adjust. Physical modeling can be elaborate and expensive to conduct on a regular basis while Computational Fluid Dynamics (CFD) can cost-effectively address this challenge. In this study, the furnace model is created with a particular loading pattern to understand the flame dynamics in the presence of a piled load. This configuration can be thought of as a computational model of the furnace with the burden at a particular stage of the melting process. Thermal efficiency and behavior of the furnace are quantified and the predicted values are compared with the operational data from an experimental reverberatory furnace.

Jan 1, 2008

By Zhenzhou Yang, Zuotai Zhang

In the present study, we proposed a method that using sewage sludge (SS) as alternative fuel and raw material to produce cement clinker. It was found that the increasing amount of SS can favor for the formation of tricalcium silicate (C3S) but the excessive amount can cause the impediment effect. Furthermore, SS contains high contents of trace elements, especially for zinc and manganese. The thermodynamic equilibrium calculation of Zn and Mn are also conducted to further understand their transformation behaviors and the results show that zine is predicted as a volatile element while manganese shows great condensed potential during the cement clinker calcination process.

Mar 1, 2017

By N. J. Themelis

In the last two decades, the Outokumpu flash smelting process has become the dominant new technology for copper smelting and has? also been applied to the smelting of other metal sulfides. The application of oxygen enrichment and improvements in concentrate burner and furnace design have resulted in ever increasing smelting rates per unit volume of the reaction shaft. This paper examines the. rate phenomena taking place in the reaction shaft of the Outokumpu furnace and compares information obtained from a mathematical model of heat and mass transfer rates to results obtained in pi1ot tests conducted at Pori, Finland, and to actual performance of a number of flash smelters around the world. 2?

Jan 1, 1985

By N. Kanari

The thermal decomposition studies of two zinc basic carbonate samples were carried out up to 400 "C by thermogravimetric analysis, boat experiments and differential scanning calorimetry measurements 'DSC'. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy, x-ray diffraction and laser particle size analyzer. The thermal decomposition of both samples started at about 150 "C and the rate of decomposition became significant at temperatures higher than 200 "C. The apparent activation energies 'Ea' in the temperature range 150-240 "C for sample decomposition were between 132 and 153 kJ1mole depending on the sample origin. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 "C suggest that the decomposition reaction probably occur in a single step.

Jan 1, 2002

By Mao Chen, Baojun Zhao, Xiangfeng Cheng, Zhixiang Cui, Leonel Contreras, Anh Nguyen

Smelting is an important process in copper production to produce matte and slag.The slag,containing about 1–12% Cu can be further processed to recover the copper contaminated, but recycle of the slag concentrate reduces overall productivity and efficiency of the operation. The best solution is to minimize the copper loss to the slag. The entrained matte droplets in copper smelting slag may originate from a few sources. The present study aims to investigate possible copper matte loss mechanisms by visualization of room temperature experiments and high-temperature examination. It is believed that the gas bubbles from the matte phase disperse the matte droplets into the slag causing entrained matte in slag. Analyses of quenched slags from industrial operation and laboratory experiments confirmed that matte droplets in the slag are extensively associated with the gas bubbles. Water model is used to simulate the procedure and the bubble behaviors at the liquid-liquid interface are observed experimentally with a high-speed camera.

Mar 1, 2017

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By E. J. Peterson

Oil shale retorting induces mineral and chemical reactions to occur on the macroscopic and microscopic levels in the kerogen-bearing marlstone. The nature and extent of the reactions is dependent upon process variables such as maximum temperature, time at temperature, atmosphere, and raw shale composition. This report describes the investigation of the mineral, chemical, and trace element release properties of spent shales retrieved from an experimental in situ retort at Occidental Oil Shale, Inc. 's Logan Wash site in Garfield County, Colorado. Correlation between mineralogy of the spent materials and the mobility of major, minor, and trace elements are indicated, and relationships with important process parameters are discussed. The progress .of carbonate decomposition reactions and silicat ion reactions is indicative of the processing conditions experienced by the shale materials and influences the mobility of major, minor, and trace elements when the solids are contacted by water. Shale minerals that are exposed to the extreme conditions reached in underground retorting form high temperature product phases including akermanite-gehlenite and diopside-augite solid solutions, kalsilite, monticellite, and forsterite. The persistence of relatively thermally stable phases, such as quartz, orthoclase, and albite provide insight into the extremes of processing conditions experienced by the spent shales. Leachate compositions suggest that several trace elements, including vanadium, boron, fluoride, and arsenic are not rendered immobile by the formation of the high-temperature silicate produce phase akermanite-gehlenite.

Jan 1, 1981

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By Seksak Asavavisithchai, Natthida Jareankieathbovorn, Areeya Srichaiyaperk

"Recycling of ADC12 alloy scraps for fabrication of open-cell aluminium foams has been conducted via pressure infiltration method of replication process. The scrap, up to 50 wt.%, was melted with pure aluminium billet, followed by infiltration in a replicated mold of polyethylene foam structure. Compared with the pure aluminium foam, the compressive strength and hardness are higher for the foams with recycled scraps. The increase in foam mechanical properties is due to the presence of Si hard phase in Al matrix. The strength and hardness of the foams also increase with increasing contents of the scraps.IntroductionRecently, open-cell metallic foams have been brought to considerable attention of many industries due to their superior properties; such as large surface area, high specific strength, thermal conductivity, high service temperature and excellent anti-microbial activity, that cannot be found in conventional materials [1, 2]. Typically, open-cell foams are used in functional applications for which a requirement of high strength materials is not demanded. Good examples of such applications include heat exchangers, bone-replacement implants, interconnects, catalyst supports, and sound insulators.Among all types of open-cell metallic foams, aluminium (Al) is the most widely used base metal, due to low material cost, low density, low melting temperature and good corrosion resistance. To improve mechanical properties of Al foam, modification of foam microstructure with addition of alloy elements or ceramic particles is commonly carried out [3, 4]. ADC12 alloy is a typical die-casting Al alloy with high content of silicon (Si) close to the eutectic point in Al-Si binary phase diagram. The alloy is extensively used in the casting industry, due to high wear and corrosion resistance, low coefficient of thermal expansion and excellent castability [5]. The mechanical properties of Al-Si alloy are strongly dependent of Si content."

Jan 1, 2012