Search Documents

By Aichun Dou

Au-Sb alloy sample in which the total amount of Cu and Ni is below 25% (wt. %). In practice, Cu and Ni were difficult to be dissolved in sulphuric acid solution by oxidative leaching under the atmospheric pressure conditions, because of the lower concentration of Cu and Ni in the sample. In this paper, pressure oxidation leaching in sulphuric acid system (POLS) followed by hydrochloric acid leaching (HAL) was employed to remove impurities in the Au-Sb alloy. The effects of variables in POLS on leaching ratios of different metals were investigated in detail. Under the optimal conditions: the concentration of H2SO4 is 1.5 mol/L, liquid-solid ratio is 7:1, the amount of oxidizer is 1.2 times of the theoretical amount, leaching time is 4h and leaching temperature is 427K, the leaching ratios of copper and nickel reached up to 99%, antimony, lead and silver were not dissolved in dilute sulphuric acid solution. The residue from POLS was then treated with hydrochloric acid solution in fixed conditions, the leaching ratio of antimony reached over 92%, the grade of gold in the ultima residue was enriched up to 66%.

Jan 1, 2016

By Animesh Jha

"Fine ceramic powders (<500 nm) exhibit exceptional physical and mechanical properties in engineered structural ceramics. The production of fine powders, in particular the non-oxide ceramics, via a cheaper route than the organic solvent route has been rather elusive. This paper examines the physical chemistry of sub-oxide vapour-phase reduction reaction for the nucleation of non-oxide ceramic phase. Well known vapour species eg SiO and BO in the production of technical ceramic powders (SiC, BN) are particularly discussed for understanding the nucleation process of SiC and BN ceramic phases respectively. The regimes of partial pressures and temperatures are particularly 'identified. The calculated nucleation rate as a function of the temperature is compared with the experimental results on powder morphology. The production of amorphous and nanocrystalline h-BN powders is discussed in the context of substrate structure and thermodynamic parameters.IntroductionThe physical and mechanical properties of ceramic components are strongly dependent on the powder particle size and morphology used for their fabrication. For example the strength (Os) of the structural ceramic components increases with decreasing average grain-size (d) in accordance with the Hall-Petch relationship: Os = 0""0 + k/(d)1/2. Here k is an empirical constant which can be established from the graphical relationship. However as the particle size approaches submicrometer-size range, the dependence of strength on the particle size becomes more complex [1]. The design of ceramic components based on nanometer-size particles have recently become an important field which can offer ceramic materials with properties comparable to their metal counterparts. Several materials based on these concepts have been developed and reported by Niihara [2]. For example, the Al2O 3-SiC nanocomposite, having average B-SiC grain size 0.3-2um with intragranular SiC particulates of 5-10 nm has unusually high strengths (1100 MN/m2) at low and elevated temperatures combined with enhanced fracture toughness (> 4 MN-ml.5) which is an unusual combination in structural ceramics. Besides mechanical properties, as the particle size of ceramic powders approaches the nanometer-size range, the charge transport properties also improve by many times. The effect of particle size on the electrical conductivity of Si3N4-TiN composites has been well documented [3.4]. The size of ceramic particulates without doubt plays a pivotal role in determining the properties of ceramic components."

Jan 1, 1996

By Katri Avarmaa

Aluminum and copper are large volume metals in electronic appliances, while tin and indium exist as common minor elements. All of these non-ferrous metals are aimed to be separated and recycled from the end-of-life electronics into non-ferrous scrap fraction(s), and further through pyrometallurgical and/or hydrometallurgical processes to pure metals. Depending on the mechanical pre-treatment processes, aluminum and copper liberation from each other varies. This study focuses on the influence of alumina on indium and tin distributions between copper alloy and iron silicate slags with 0, 9 and ∼16 wt% of Al2O3. The experiments were executed with an equilibration-quenching-EPMA technique in an oxygen pressure range of 10−10–10−5 atm at 1300 °C. The metal-slag distribution coefficient of indium remains constant as a function of alumina in slag, while that of tin increases. Therefore, aluminum in feed or alumina addition to the slag improves the recovery of tin into copper. Nevertheless, oxygen pressure has clearly more significant influence on the behavior of both the metals in the smelting conditions.

By V. L. Stolyarova

The high-temperature Knudsen effusion method was used to study partial pressures of vapour species, activities of components and the Gibbs free energies in the DyF3-Dy2O3 system at the temperature (1357±5) K. Partial pressures of vapour species were obtained by the ion current comparison method, with the DyF3 partial vapour pressure over pure DyF3 as a standard. The equilibrium constant of the gaseous reaction DyF3 + DyOF = Dy2OF4 is evaluated. Thermodynamic data obtained are in a agreement with the available phase diagram of the DyF3-Dy2O3 system. Results of the present study illustrate the negative deviations from the ideal behaviour in the system.

Jan 1, 1997

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Heinz Böni, Christian Ludwig, Bernhard Steubing, Uca Silva

"Chile will soon have to find solutions for dealing with rapidly growing quantities of Waste Electrical and Electronic Equipment (WEEE) due to its strong economy and fast increase of internet and communications technology usage. To support this process, the state of the Chilean recycling infrastructure as well as government, industry and consumer efforts to deal with ewaste were analyzed. Current e-waste quantities were assessed and future flows were predicted using a material flow analysis model. In this model computer hardware was used as tracer equipment for WEEE. Best available numbers indicate that today’s formal recycling infrastructure receives less than 3% of the annual quantities of computer waste. This study represents the most comprehensive analysis regarding e-waste in Chile, identifying relevant streams of e-waste and providing a basis for authorities and producers of electronic goods in order to take the necessary actions to establish an adequate recycling system.IntroductionSince 1991, Chile has experienced a period of strong economic growth. It is amongst the countries with the fastest development in the sector of Information and Communication Technologies (ICT) in Latin America and the number of people with access to ICT has been growing rapidly. The high growth rates of the computer market over the last years are representative for the ICT sector with the consequence that the generated quantities of electronic waste are increasing rapidly [1, 2].Waste Electrical and Electronic Equipment (WEEE) or e-waste is “any appliance using an electric power supply that has reached its end-of-life” as defined by the OECD [3]. Even though the overall waste management in Chile has improved much over the last decade, the issue of ewaste was hardly addressed. Due to the value of the materials contained in computer waste - such as precious metals, basic metals as copper or plastics - it may be assumed that an important quantity is already being recovered. This usually takes place on the informal market under questionable conditions for human health and the environment [1, 2, 4]."

Jan 1, 2008

By T. Shibasaki

Purification of copper electrolyte at Naoshima is carried out by two stage liberation to completely depress copper and impurity ions followed by concentration of the solution to produce crude nikel sulfate as by-product. A new nickel recovering process has been developed and pilot tested recently. It consists of the following process steps.; neutralization of spent electrolyte from liberation section to remove free acid and most part of remaining impurity ions, refining and nickel concentration by solvent extraction, and crystallization of pure nickel sulfate from concentrated strip solution. This paper describes the results of laboratory and pilot plant tests, then briefly discusses feasibility of the proposed process.

Jan 1, 1987

By Payal Bakshi, Sangeeta Tiwari, Mohini Saxena, Anusha Sharma

"Recycling and reuse is perhaps the most favorable and beneficial way to solve the problem of industrial waste disposal. However, the use of industrial wastes like fly ash, tailings etc is in practice for brick manufacturing, land filling, embankments filling etc. These existing practices do not add enough value to the wastes. Moreover, some wastes may have very good potential to be incorporated in valuable products like paints. This study reveals about the value addition of industrial wastes like fly ash, copper tailing and blue dust as an extender in paints. Comparative properties and characteristics of these three wastes for application in paints are discussed. Fly ash, copper tailing and blue dust were characterized for physical, chemical and mineralogical properties and used in different paint formulation based on their potential to the particular application. Fly ash has been found very useful in enamel, primers and flat paints while copper tailing was found suitable in oil based paint formulations. The performance of fly ash and copper tailing paints were evaluated by comparing with those of conventional whiting extender. Blue dust was compared with conventional iron oxide for use in priming coats. The extender properties of these new material and paints prepared out of blue dust, fly ash, copper tailing, were found better than the existing related materials.IntroductionIndustrial development and environmental reforms should run parallel to benefit each other. This is the best policy, which must be adopted by industries for the sustainability of the current modern life. The high degree of industrialization and urbanization adds scads of waste resulting problem of pollution and challenges of their safe disposal. The nature of waste depends on the process that produces waste as its by-product. Therefore, policies/plans are prepared by keeping the view of possible potential hazards. Among the different wastes some are generated in the industries, which have great importance in the country’s economy, like fly ash waste from thermal power industry and mining waste. In India the total contribution of thermal power in the total electricity generation is more than 70% and it produces about 123 million ton of the fly ash annually [1]. On the other hand mining plus extraction of ferrous and nonferrous metals also produce waste in million tonnes of categories [2]. Since the generation of this waste is very high they cover large land area for their disposal and dumping [3]. The storage of this waste in the dumping sites for long time duration may cause problem of land, surface water, ground water and fertile soil contamination [4]. As far as Indian fly ash is concerned it does not contain toxic element over the limits of hazardous waste [5]. However, in general most of the metals deposits are found in the form of pyrite based ores. Mining wastes contain toxic elements e.g. heavy metals in varying amount, which get mobilized when pyrite get oxidized to sulphate producing sulphuric acid [6,7]. These ores contain very less amount of targeted metals in themselves thus they require extensive preprocesses for concentration of the metals [8]."

Jan 1, 2008

By C. M. Acuña

At the Chuquicamata Division of Codelco-Chile high arsenic concentrates are produced, which at the smelter are processed via the Outokumpu Flash Furnace and Teniente Converters to obtain copper mattes. In the case of the Teniente Converters the production of matte grade near white metal composition is a common practice since the eighties and provided in the pyrometallurgical route no appropiate measures are taken, penalties have to be paid because of arsenic content in the anodes. During smelting huge volume of slag is produced and elimination of arsenic by slagging at this step is not economically attractive. Although during fire refining is possible to eliminate arsenic by use of mixtures of calcium and sodium carbonates this alternative is expensive, takes long process time and decreases the lifetime of the refractory lining. In spite of these facts a reasonably way to control arsenic in metal, and therefore in the anode, is taking, action in the converting step. The effects of oxygen and arsenic content in metal, arsenic in white metal and basicity index of the slag upon the distribution coefficient of arsenic between metal and slag were investigated at pilot and industrial levels. The best results are obtained for metals around 7,000 ppm oxygen and 0.3 basicity index slag, which results in a 5.7 distribution coefficient for a 5,800 - 7,100 ppm arsenic content in white metal, 18%-24% CaO slag at 1473 - 1523K. Furthermore, no significant/visible refractory wear has been realized.

Jan 1, 1999

By Fathi Habashi

While it is commonly known that the precious metals and to some extent copper occur in the native state, it is less known that mercury, iron, nickel, and cobalt do occur also in the native state; the last three (Fe, Ni, and Co) usually occur together in form of an alloy. The particle size varies greatly from less than 10 microns (gold and mercury) to about 400 tons boulders (copper).

Jan 1, 1993

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992

By T. V. Jayaraman

Fe-Ga alloys, with compositions around 27.5 at % Ga, can be heat treated to obtain ? (ordered bcc), DO19 (ordered hexagonal), and L12 (ordered fcc) ordered structures. Our earlier work using polycrystalline samples had shown that magnetostriction is strongly influenced by ordering in this alloy. Here more detailed study of the correlation between ordering and magnetostriction using single crystals of Fe 27.5 at. % Ga alloys is reported. Single crystals of Fe 27.5 at % Ga were grown using Bridgman single crystal growth technique. X-ray and electron diffraction were used to study the ordering in this alloy. Magnetostriction measurements were carried out at no load conditions. Elastic constants were measured using Resonant Ultrasound Spectroscopy.

Jan 1, 2006

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04&apos; pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By Bin Xu, Qian Li, Ya-xuan Wang, Yong-bin Yang, Xi Zhang, Tao Jiang

The effects of common associated sulfide minerals including pyrite, arsenopyrite, galena and sphalerite on thiosulfate leaching of gold were studied in this work. Sulfide minerals had significant effects on gold leaching because that the dissolved products of sulfide minerals precipitated on gold surface to form coating layer. The degree of sulfide minerals impact on gold dissolution decreased in the order of pyrite ≈ galena > arsenopyrite > sphalerite, while the degree of effects on thiosulfate consumption decreased in the order of pyrite > arsenopyrite > sphalerite > galena. The additive CMC (Carboxymethyl cellulose) could not only reduce thiosulfate consumption but also increase gold dissolution. The mechanism of this might be that CMC could restrict the decomposition of thiosulfate by cupric ions and the precipitates on gold surface.

Jan 1, 2015

By Luísa Maria Abrantes

Environmental control is becoming more and more stringent. As conventional processes for zinc production are pollutant routes, alternative methods have become an important subject of research. In this regard, the leaching processes have aroused a considerable interest, namely the electrochemically induced approach. The behaviour of zinc concentrate ore in the leaching processesses is influenced by several parameters. Chloride concentration and leaching solution pH, time and temperature of reaction were studied in order to evaluate their influence on the zinc recovery. The efficiency of the leaching process for zinc extraction is performed by factorial design. The experiments were carried out by 23 and 22 factorial designs of the factors. Results show that all factors, except for the time of reaction have a significant influence on the optimisation process, within each experimental region.

Jan 1, 2001

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Roberto Parra

The wear and corrosion phenomena in the furnace lining of the ferrous and non ferrous pyrometallurgical processes are complex problems where chemical, interfacial and mechanical phenomena are presents. The characteristics of the processes determine the conditions to which these materials are submitted, where the thermal conditions reached during the operation is one of the most important parameter. Assuming that all the degradation phenomena are thermal activated, the rate of the different steps of the wear mechanism will depend on the thermal field in the lining. In view to apply the independent physicochemical knowledge of degradation mechanisms to the analysis and design of furnace lining the methodology of the Nodal Wear Model (NWM) was done. It combines the mathematical modelling of the heat transfer in the lining with the physicochemical control equation for the wear-corrosion phenomena. The NWM has been applied to different examples: theoretical analysis, laboratory scale test and industrial applications. We present in this paper the theoretical background of the model and two examples of applications: the sole of an electric furnace and the earth of a blast furnace.

Jan 1, 2006