Search Documents

By G. Coryell, S. Blaskovich

"A computer model has been developed to simulate the flash furnace and converter operations at the ASARCO Hayden Copper Smelter. The focus of the modeling was to optimize the converter operation to eliminate high matte level episodes in the flash furnace. These episodes (reducing feed to the furnace) resulted from the lack of converter operation scheduling. The model provided ""what if?"" scheduling scenarios that led to increased efficiency of the converter and flash furnace operations.This paper discusses alternatives studied to optimize the converter operation and the development of the computer modeling program, including implementation of the project. The discussion details the results of the project including the conversion from batch to a real time converter scheduling process. IntroductionASARCO's Hayden Smelter consists of a fluid bed drying system, an Inco oxygen flash smelting furnace, Peirce Smith converters, two anode furnaces and two casting wheels, gas cleaning plant, 2800 stpd sulfuric acid plant, 650 stpd oxygen plant and 200 gpm water treatment plant. The process flow sheet of the plant is shown in Figure 1.Over the past several years, the Hayden smelter has been involved in productivity improvement and cost reduction programs. This has been necessary to become a low cost copper producer in today's market. Part of the productivity improvement program was the use of process control to streamline the flash furnace and converter operations. Process control, through the use of computers and electronic controllers, has played an increasingly important role in optimizing processes in the Hayden Plant since the startup of the Inco flash furnace in 1983."

Jan 1, 1989

By N. Shi, T. C. Lowe, S. J. Zhou, M. L. Lovato, Y. T. Zhu, J. A. Valdez, W. R. Blumenthal, M. G. Stout

"A major problem of short-fiber composites is that the interfaces between the fiber and matrix become a limiting factor in improving mechanical properties such as strength. For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber, thus reducing the ineffective fiber length. However, a strong interface will make it difficult to relieve fiber stress concentration in front of an approaching crack. Stress concentrations result in fiber breakage. We report in this paper an innovative approach to overcome this problem: reinforcement morphology design. Short-fibers with enlarged ends are processed and used to reinforce a polyester matrix. The initial results show that the bone-shaped short-fibers produce a composite with significantly higher strength than can be attained with conventional short, straight fibers.IntroductionThese interfaces between the fiber and the matrix in short-fiber composites play a critical role and, in many cases, become a limiting factor in improving such mechanical properties as strength and toughness of the composites (1-4). For a short fiber, a strong interface is desired to effectively transfer load from matrix to fiber. A stronger interface can reduce the ineffective length at both ends of the fiber and, therefore, can increase the effective length that carries load (5-9). However, with a strong interface it is difficult to relieve fiber stress concentration -in front of an approaching crack; and such stress concentration can result in fiber breakage (10, 11). This effect is particularly severe for ceramic matrix composites, because of their low matrix toughness and lack of plasticity. Even for a composite with a highly ductile matrix, such as plastics, too strong an interface may still cause successive adjacent fiber breakage and subsequently reduce composite toughness (1, 11). On the other hand, a weak interface significantly decreases the fiber load-carrying length due to ineffective load transfer and complete fiber interfacial debonding and pullout during loading. A compromise in the interfacial bond strength will also compromise the load-carrying potential of short fibers."

Jan 1, 1998

By Uchil Jayagopal, M. Krishna, P .. V. Krilpakara, S. Manjunath

"There have been a pioneering efforts over the last forty years in the development of metal matrix composites (MMCs) as a new engineering materials, having improved properties, light weight characteristics and competitive costs compared to traditional materials. Following recent advancements in casting technology and the use of melt stirring device by foundries, discontinuously reinforced MMCs where prominent alloys are reinforced with particulates or short fibres and the being employed ·in the production of castings targeted for automotive and aerospace application.The ZA-27 alloy has a high strength compared to zinc or alluminium alloys with a lower melting temperature. The main objective of the present research is to study the effect of quartz particles on the mechanical behaviour of ZA-27 alloy composites. The results showed that the ultimate tensile strength, hardness, Young's modulus of the composite gradually increased with increase in the weight percentage of the quartz reinforcement. However overall ductility decreased with an increase in quartz reinforcementIntroductionMetal matrix composite (MMCs) offer outstanding benefits as they combine metallic properties with ceramic properties there by yielding improved physical and mechanical properties.1Among the various type of MMCs particulate reinforced composite are the most versatile and economical2. By suitable choice of metal matrix and particulate system a wide range of properties combination can be obtained such as strength, modulus, fiiction.al resistance, tribological performance and machinability. These composites are capable of replacing conventional alloys in a considerable range of applications. They also offer significant saving in energy and resources"

Jan 1, 2000

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008

By Takahiko Okura

Japanese non-ferrous industry introduced large-scale smelting plants along seashores for overseas concentrates with increasing demand of metals around 1970s. Although serious environmental pollution became obvious, with economic growth, the industry got rid of pollution by installing new processes and improving operation technologies. At present, over 99.8% of sulfur input to smelters is fixed as stable compounds. Through those decades Japan had steep rises of oil prices, sudden change of exchange rate, and inadequate treating charges, we were faced to consider the closure of smelters. The industry has survived by increasing productivity, saving energy and reducing manpower. Furthermore the industry made great effort to recycle valued metals from scraps and wastes for the resources-recycling society. Academic research also contributes to support these individual technologies. Thus the industry has fostered world-acclaimed technologies in terms of efficiency and energy conservation. This paper presents technology development and environmentally-benign sulfide smelting processes.

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Shigeru Ueda, Shin-ya Kitamura, Shohei Koizumi, Xu Gao

Steelmaking slag was confirmed to be a useful fertilizer for paddy growth as it efficiently supplies Ca and Si to soil water. In addition, supplement of Fe from slag fertilizer has been expected to suppress the H2S generation in paddy soil, especially for the degraded paddy soil. However, on the basis of our previous research, the Fe dissolution ability changed with slag brands, and even some brands could dissolve Fe under paddy soil pH, the supplying ability were not high. To improve Fe dissolution, we found that among various kinds of Fe-rich mineralogical phases in slag, the CaO–SiO2–FeO glassy phase showed highest water solubility of Fe. Because the CaO–SiO2–FeO glassy phase was a quenched molten phase, its dissolution behavior may depend on chemical composition, and this is important for controlling slag composition to produce fertilizer which can easily release Fe. Therefore, in this research, the CaO–SiO2–FeO glassy phase of various CaO/SiO2 ratio, Fe2+/T–Fe ratios, and FeO contents were synthesized, and the dissolution behaviors of Fe as well as other cations from these synthetic glassy phases into an aqueous solution at pH of 5 were investigated. The result showed that the dissolution ratio of Fe increased significantly by increasing Fe2+/T–Fe ratio. An increase in FeO content of glassy phase also increased the dissolution of Fe. In addition, the Fe dissolution ratio showed a local maximum with increasing CaO/SiO2 ratio.

Mar 1, 2017

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By Zhenyang Wang, Xingle Liu, Xiangdong Xing, Shan Ren, Hongen Xie, Jianliang Zhang

"Non-isothermal combustion experiments of different additive amount of bituminous (0, 20, 40, 60, 80, 100 wt%) were conducted by synthesized thermogravimetry analyzer(STA409PC) from room temperature to 900°C in air. The changes of combustion characteristic parameters o f pulverized coals in different atmospheres are analyzed. The results show that DTG curves of coal combustion move to low temperature zones when the amount of bituminous increases. It indicates that both ignition and burnout temperature are lower, burnout time decreases, combustion characteristic index obviously increases, and combustion performance of blending coal are improved. The iso-conversional method involving Kissinger-Akah-Sunose (KAS) method was used for the kinetic analysis of the main combustion process. The results indicated that, when the additive amount of bituminous varied from 0 to 100 wt%, the value of activation energy which would sharply reduce if the additive amount of bituminous was under 60% increased from 133.94 kJ•mol-1 to 78.03 kJ•mol-1by using KAS method.IntroductionPulverized coal injection (PCI) to blast furnace (BF) is an important way for saving energy and reducing resource consumption during the ironmaking process. In order to acquire higher coal injection quantity, the relevant research topics in the field of pulverized coal combustion technology such as enhancing the efficiency of pulverized coal combustion, improving the combustion characteristics and reducing the harmful gas emissions and so on received extensive attention in recent years [1,2]. The combustion of blending coal when the appropriate proportion is selected for coal and also mixed well- distributed could give full play to the advantages of various types to make up the defects of single coal which is widely used throughout the world. So the blending coal injection to BF could produce a good impact on safety and economy for productive process. Therefore, a large amount of experimental researches on the combustion characteristic of blending coal for anthracite and bituminous were carried out by experts and scholars around the world [2-7].Nevertheless, the systematic research on the combustion behavior of anthracite with different content of bitumite in a thermogravimetric analyzer (TGA) is less. So in this paper, using the method of multiple scanning rate of conversion method, bituminous to promote the pulverized coal combustion reaction was studied to analyze its promotion mechanism of pulverized coal combustion reaction process, and the kinetic parameters of activation energy was also calculated, which to provide theoretical basis for the rationalization of resource utilization."

Jan 1, 2014

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By E. Kuzeci, R. Kammel

"Lately various voltametric methods have gained increased attention as an analytic tool in hydrometallurgy. Voltammograms with mercury drop electrodes or glassy carbon electrodes provide information about the electrocrystallization of cathodic deposits and allow calculation of kinetic data by means of characteristic parameters like the peak potential and peak current and their variation with the voltage scanning rate.Cyclic voltammograms are also suitable for identification of reaction sequences. Voltammograms with carbon paste electroactive electrodes containing metal sulphide additions reveal information about the dissolution behavior. The stripping voltammetry can be applied to analyze metal ions and organic additives (e. g., thiourea) in extreme low concentration. Typical application of the various methods studied with microcomputer controlled measurement system are explained by examples selected from copper hydrometallurgy.IntroductionThe use of electroanalytical methods in metallurgical process control can be dated back to the starting period of industrial copper refining, when the deposition of the metal ions was followed electro-gravimetrically by weighing the electrode with deposits (1). The principles of metal deposition and dissolution have not changed but the methods to follow these phenomena were subjected to noticeable developments and especially the introduction of polarographic investigations by Heyrowsky (2) has greatly contributed to the progress in electro-analysis. A review about the fundamental work on the electrochemical kinetics in earlier time is compiled in a monograph of Vetter (2). With the steady improvements in the instrumental techniques, it is nowadays possible to apply several current and potential modulations for measurements with improved selectivity and sensibility. There is however, still a lack in theoretical interpretation of the data obtained. More theoretical information are already available for linear voltametric methods for systems where reduced as well as oxidized species are dissolved in the electrolyte (4, 5). Some recent investigations have also shown the reliability of these techniques to study electro-crystallization (6, 7). Main fields of the application in the hydro - and electro-metallurgy are:"

Jan 1, 1989

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By Baoxiang Zhang, Jing Zhang

"As extruded Mg-9Zn-0.6Zr-2Er magnesium alloys were hot-rolled at 400°C, followed by solution treatment at 400 °c for 1. 5h and artificial aging at 200°C for 10h. Microstructures and tensile mechanical properties of the alloys after hot rolling, solution and aging treatment were examined respectively. Optical micrographs of the as-rolled and as-solution alloys showed fine grain structures, due to the formation of Er-and Zn-bearing compounds at grain boundaries which obviously improved the thermal stability of the alloy. Yield strength as high as about 335 MPa was obtained for the as-rolled alloy, showing that the mechanical properties of the alloy was greatly benefit from the grain refinement and dynamic precipitation of fine MgZn2 during hot rolling. Due to solution heat treatment, vast majority of the Mg-Zn phases dissolved into the matrix, and precipitated out again as fine dispersoid during the subsequent aging, resulting in an enhanced aging-hardening effect.IntroductionWith high specific strength and low density, magnesium alloy has stimulated significant interest for the applications in microelectronics, aerospace and automobile industries. Due to its HCP structure, magnesium alloys exhibit relatively poor strength and ductility. Great efforts have been made to improve the properties of magnesium alloys.Thermo-mechanical processing which combined with subsequent heat treatment can strengthen magnesium alloys due to the strain-hardening mechanism, homogeneous distribution of second particles and grain refinement [1, 2]. However, commercial wrought magnesium alloys have high tendency of grain growth at high temperature due to lack of effective solutions to stabilize the microstructure [3, 4, and 6]. But Magnesium-RE alloys containing high rare earth were reported to have remarkable thermal-stability, Rare earth (RE), such as Y, Nd, Yb, Gd, Ce, were known to form second-phase particles that have higher thermal stability combining with Zn and matrix in Mg[12-17]."

Jan 1, 2012

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By Guohua Bai, Yuanbo Zhang, Guihong Han, Zijian Su, Daoyuan Zhang

"Specularite ores have poor hydrophilicity and ballability as well as inferior high-temperature reactivity, which restrict the large-scale application of them in the pelletizing and sintering production. Modified humic acid (MHA) organic binders are firstly used for pellet preparation from specularite in this paper. The results show that the drop strength of green pellets is 3.7 times/0.5m and compression strength is 12.5 N/P by using 1.0 wt% MHA as binder. Under the optimal experimental conditions of preheating temperature 980 °C, preheating time 12 min, roasting temperature 1280 °C and roasting time 10 min, the preheated pellets have the compression strength more than 400 N/P, and that of roasted pellets is 2747 N/P. The strength of finished pellets meets the requirements of blast furnace iron-making. MHA is a kind of more effective organic binder for specularite pellets compared with the inorganic bentonite.IntroductionAcid Pellets have advantages of good strength, uniformity particle size, high iron grade and good reducibility, which can be used as high-quality burdens for blast furnaces [1]. With fast development of Chinese iron and steel industry domestic magnetite concentrates with high grade of iron and good firing performances become shortage.Imported specularite ores have advantages of low price and high grade of iron (generally above 67 wt%), so the application of them in pellets is an effective way for sustainable development of pellet industry in China. However, the specularites have not been utilized in pelletizing and sintering at present because of the poor ballability and high-temperature reactivity [2, 3]. Most of the pellet plants use bentonite as binders, the amount of which is about 2~3 wt%. The pellet production practice shows that 90 wt% bentonite is still residual in finished pellets and reduces the iron grade [3]. Developing a new organic binder instead of bentonite is very important to the high-quality pellet production. On one hand, the consumption of bentonite is obviously reduced, resulting in decreasing the ironmaking coke ratio and slag discharge; On the other hand, the iron grade of finished pellets are improved, which brings the benefit for the ironmaking production."

Jan 1, 2011

By Oscar Restrepo, Juan C. Nino, Henry A. Colorado

New and extraordinary physical-chemical properties of materials at nanoscale open up new applications for the building and infrastructure industry such as structural reinforcements, electronic properties and energy harvesting. Therefore the issues and risks associated with the manufacturing of nanomaterials are now of big concern due to the large volumes and typical processing involved in this industry. This paper presents a discussion and selected applications of nanotechnology in the construction and building materials: from metals and alloys, clay and minerals, ceramics, cement and concrete, asphalt, wood and composites, to finishing systems and some of the most used characterization techniques. Besides the progress in some areas, nanotechnology is just emerging in this field, with many challenges and opportunities, problems unsolved and business opportunities. A discussion regarding the potential health issues and risks of using nanomaterials for workers and the potential environment effects is included as well. New images and diagrams are presented and discussed.

Mar 1, 2018

By Y. Shigeno

The reactivity of a porous solid is a strong function of its pore structure (porosity, pore surface area and pore size distribution). It follows that reactivity could be altered by altering pore structure; one way to achieve this is by chemical vapor infiltration whereby a gaseous species is reacted in the porous solid to produce a solid. Experiments were carried out in which the pore structures of various carbons were modified by cracking methane within the pores; oxidation rates of the carbons were then measured for both infiltrated and original samples. For coke it was found that two indices of coke performance used in the steel industry (CRI and CSR) can be greatly improved following a small amount of infiltration. Infiltration/oxidation results are interpreted in terms of measured pore structure changes.

Jan 1, 1993

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By Tao Jiang

Germanium is widely used in many fields, and the production of germanium is very important. The effects of initial sulfuric acid concentration, liquid to solid ratio and other parameters on the leaching rate of germanium and zinc from germanium-bearing zinc oxide has been studied. The occurrence and form of germanium and other elements in the leach feed and the leach residue were studied by EPMA, XRD and chemical analyses. The experiments showed that the leaching rate of germanium and zinc was 91% and 88%, respectively under optimal conditions. Wurtzite was the main limiting factor for the leaching rate of zinc while the leaching rate of germanium was limited by insoluble germanium compounds. Furthermore, it was found that some germanium was bound up in galena in the leach residue. These results may be helpful for further improving the leaching rate of germanium in germanium-bearing zinc oxide.

By V. I. Lakshmanan

Crown ethers are gaining importance in separation technology specifically for rare earth elements (REE, La to Lu plus Y) and precious metals (Au, Ag, Pt, Pd, Rh and Ir) due to their specific binding ability, metal complex stability and high extraction efficiency. The selectivity of crown ethers in extraction of these metals depends on different factors, including the cavity diameter and nature of a donor atom of the crown ether, size and charge of the metal ion, diluents and counter ion. Demand for strategic REE and precious metals are consistently increasing in the world while the separation of these metals is most challenging tasks. In this paper, the use of crown ethers in separation of REE and precious metals, reaction mechanisms and simplified process flowsheets will be elucidated. New reagents with high selectivity for the separation of these metals are further expected to produce high purity metals.