Search Documents

By Nickolas J. Themelis

The flash oxidation and smelting of mineral sulfides is a very prominent metallurgical achievement of the second part of this century. Its initial industrial implementation owes much to the work of Petri Bryk, in Finland, and Paul Queneau, in Canada. However, attempts to develop flash reduction pro- cesses, such as the reduction of iron oxide concentrates with hydrogen, have not yet been successful. The author, on the basis of experimental studies on both kinds of flash reaction systems, examines the respective rate controlling phenomena and the relative rates of flash oxidation and flash reduction.

Jan 1, 1993

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By Juan Ruiz-Ornelas, Yousef Mohassab, Ricardo Morales-Estrella, Hong Yong Sohn, Noemi Ortiz-Lara

The effect of mechanical activation on the reduction kinetics of magnetite concentrate by hydrogen was studied. The magnetite concentrate was milled for 8 h using a planetary mill. After the milling process, the average particle size was reduced from 14 to 4.4 m resulting in a lattice microstrain of 0.30. Thermogravimetric experiments were conducted to focus on the chemical reaction as the rate controlling factor by eliminating external mass transfer effects and using a thin layer of particles to remove interstitial diffusion resistance. The onset temperature of reduction was decreased due to the mechanical activation, and the degree of conversion was decreased by sintering of particles which was confirmed by SEM analyses. In view of the results, a reaction rate expression is discussed from which the activation energy is calculated.

Jan 1, 2016

By Yilin Fang, Alain Bonneville, Timothy. D. Scheibe, Zhijie Xu

"We present a hydro-mechanical model for geological sequestration of carbon dioxide. The model considers the poroelastic effects by taking into account the coupling between the geomechanical response and the fluid flow in greater detail. The simplified hydro-mechanical model includes the geomechanical part that relies on the linear elasticity, while the fluid flow is based on the Darcy's law. Two parts were coupled using the standard linear poroelasticity. Analytical solutions for pressure field were obtained for a typical geological sequestration scenario. The model predicts the temporal and spatial variation of pressure field and effects of permeability and elastic modulus of formation on the fluid pressure distribution.IntroductionIn order to achieve a substantial reduction of CO2 emissions and alleviate the atmospheric carbon problem, massive scale carbon sequestration is required involving millions of tons of carbon dioxide injection over several decades. The geomechanical response is important upon the injection of substantial supercritical carbon dioxide into deep geological formations. Supercritical CO2 is less dense than brine waters and the buoyancy driven flow of CO2 requires the aquifer to be capped by low permeability rock (""caprock"") to prevent the upward migration of C02 (as shown in Fig.1 ). Massive scale injection of C02 changes the overall stress state in the caprock and formation. This change leads to large deformation that can damage the caprock, create fractures, and open new flow paths for supercritical C02. Therefore, a coupled hydromechanical model becomes essential for the caprock integrity analysis."

Jan 1, 2012

By Chai Liyuan

This paper focused on the preparation of porous ceramic pellets for microorganism carriers. A new method for the process was developed using simple gel-casting and bubble-in-water-in-oil type of multiphase double emulsion. The globules, consisting of a foamed sepiolite slurry suspension, were dispersed and consolidated in spherical shape in liquid paraffin as gelation progressed. The green pellets were sintered at 1100°C. The influence of surfactants, extension ratio and impeller revolution rate on the process and characteristics of the pellets was investigated. The pellet size was in the range of 1~4mm and determined directly by impeller revolution rate. The fine cell diameter of porous ceramic was in the range of 100~500m and the micropore diameter was less than 5m. The inner macropores were interconnected and extend to the external surface. It is impossible to analyze a result by SEM micrographs and digital camera.

Jan 1, 2006

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The disposal of wastes is a serious environmental problem, since available landfill space is dwindling. Their treatment by pyrolysis or combustion has merit, and the corresponding fuel or power production is of technological interest. However, such processes need a rigid control of emissions. This work addresses the gaseous light hydrocarbons (LHCs) generated during sequential pyrolysis and partial oxidation of unserviceable tires, PET bottles, com wastes (DDGS) and sugarcane bagasse in a two-stage laminar-flow horizontal furnace, kept at 1000 °C. Gas chromatography was used to identify and quantify the components of the emitted gaseous light hydrocarbons. The results showed that the biomass residues generated the highest emissions of aliphatic hydrocarbons, whereas PET generated the most aromatic hydrocarbons. When stainless steel meshes were inserted in the exhaust flow, it was found that hydrocarbon emissions were curtailed; as such meshes catalyzed partial conversion of these carbon-bearing gases to carbonaceous nanomaterials.IntroductionLight hydrocarbons (LHCs) are volatile organic compounds, consisting of hydrogen and carbon with low molecular weight; the most common species are methane, ethane, propane, butane, etc. LHCs are valuable since they are a very important energy resource. However, uncontrolled release of light hydrocarbon gases to the atmosphere should be avoided [l, 2]. In this work, a development is presented for the evaluation of LHCs generated during the controlled pyrolysis/combustion of several wastes in a two-stage laminar-flow horizontal furnace. Samples of unserviceable tires, post-consumer PET bottles and waste residues from the bioethanol industry (DDGS and sugarcane bagasse) were burned. A catalyst system, consisting of stainless steel screens, was tested for its effects on the gaseous emissions."

Jan 1, 2011

By Florian Aurelian, Mihai Popescu

"It will be tested four types of “geochemical barriers”. All those mixtures were contacted with mine waters containing uranium, radium and heavy metals. The loading capacity was determined. The optimum mixture was determined and its efficiency was tested within an uranium areal, where the activity was stopped. It was determined the possibility to recover the radioactive elements and the heavy metals from the investigated barriers.IntroductionThe paper presents the results concerning the performances of some “geochemical barriers” used for the decontamination of mine waters from uranium mining sites, which were tested in lab and in situ.ExperimentalThe research activity was carried out in lab and on the site.In the lab a module was constructed in order to follow up the uptake capacity of the “permeable reactive geochemical barriers” used to remove the radiolelements from the contaminated waters originated from the uranium mining industry. The barriers, which were used, are made of cheap natural materials, which can be easily got (wood chips, peat coal, sawdust, iron span, steel and zeolitic tuff). The following types of barriers were tested:•, 1st barrier: peat coal, sawdust, zeolite on weight ratio of 1/1/1;•, 2nd barrier: bentonite, sand, wood chips, peat coal on weight ratio of 1/1/1/1;•, 3rd barrier: iron span, steel, sawdust, peat coal on weight ratio of 2/1/1;•, 4th barrier: iron span, steel, sand, firry wood chips on weight ratio of 1/1/1.Lab researches concerning the uranium uptake capacity of the above described “reactive barriers” pointed out that the 3rd mixture (iron span, steel, sawdust, peat coal on a ratio of 2/1/1) didn’t reach the maximum uranium uptake capacity not even after eleven contact stages (the uptake capacity being of 70.6 mg U/ kg of mixture) and the mixture of peat coal, sawdust and zeolite has an uranium uptake capacity of 26.6 mg U/kg of mixture and becomes saturated after four contact stages.Each one of the components involved in physical-chemical processes of sorption, reduction and precipitation, will determine the diminution of uranium and other metals contents upstream the permeable reactive barrier."

Jan 1, 2008

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By M. Nishikawa

The Hachinohe Smelter employs the Imperial Smelting Furnace (ISF) for production of zinc and lead and handles a large number of concentrates and recycled materials. In recent years, recycled materials such as zinc-bearing materials, lead sludge and Waelz oxide have provided up to 30% of the feed materials at the plant. To allow for a satisfactory operation using such a wide range of recycled materials, the Hot Briquetting Plant was built in 1986 and started its operation in January 1987. In April 1988 the zinc production capacity of the ISP was increased from 81,000 to 101,000 tonnes per year. The additional production in the ISP has been attributed to the utilization of the hot briquetting process. This paper describes the various facts of the smelter, concentrating on hot briquetting operations and treatment of hot briquettes in the ISF.

Jan 1, 1991

By Chris T. Vild

"ABSTRACT NOT AVAILABLEPRESENTATION SUMMARYIntroductionToday, light gauge aluminum scrap is melted in sidewell furnaces using natural gas reverberatory burners. The scrap is introduced into the sidewell adjacent to the combustion chamber through a submerged archway. Super-heated metal is then pumped into the sidewell where it aids in melting the scrap. From the sidewell, the flow is returned to the combustion chamber through a second submerged archway at some lower temperature. Normally, the burners are set at a designed high fire level and the scrap is introduced at a rate to attempt to mat.ch the burner input. A thermocouple in the bath is programmed to throttle back the burners to low fire if a high temperature limit is exceeded.Jn many cases the thermal efficiencies of these furnaces can be very low. With inadequate circulation, air and natural gas furnaces run at a dismal 18% thermal efficiency. If a circulation system· is added, the efficiency can jump to 28%. For a $100 million lb/yr recycling facility, and natural gas prices reaching $4.50 per million Btu, fuel cost at 18% efficiency can reach $1 million per year. A 10% increase in thermal efficiency saves $350,000 a year in fuel costs.With an increase in thermal efficiency, furnace utilization also increases. A 10% increase in thermal efficiency would result in a 20 million Btu furnace producing 12,000 lb/hr up from 8,000 lb/hr or 35 million lb more produced per year. This is a 33% increase in output.Most current furnace development has focused on burner technology using oxy-fuel, regenerative burners, etc. However, thermal efficiency is also largely effected by the molten metal circulation rate and how well the scrap is mixed into the superheated metal. Therefore, the flow dynamics should be optimized first, before installing of more thermal power.Jn an effort to understand the effect of these variables, a series of computer models were made and the critical factors studied with the goal of demonstrating an increase in thermal efficiency and production. Large-scale graphical representations of these models will be presented."

Jan 1, 2000

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By C. Cánepa

In the treatment of many problems related with the optimization of a given ore dressing process, microscopic studies can provide invaluable assistance. Such studies are generally carried out through mineralogical determinations both qualitatively and quantitatively. Frequently the solution of a specific problem requires the combination of these in adequate proportions. Often the nature? of the problem poses some conditions regarding the way the microscopic determinations are made in order to yield useful information. Most publications applied to mineral beneficiation show results of ore microscopy without mentioning the methodological details involved in the determinative work and therefore it is not possible to judge their reliability and/or their relevance. As methodology must necessarily change from case to case, it is very important for the microscopist to identify first the direct and indirect mineralogical information required to solve the problem. Without such guidelines selection of methods for the qualitative and/or quantitative determinations cannot be made.

Jan 1, 1981

By G. C. Yao

Branch and needle-shaped intermctallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallie compound particlcs may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermctallie compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "C" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25>< 15" 130mm3 with a lateral baffle inside. The separator was put into the interspace of the "C" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhanees signifieantly the efficiency of impurity separation.

Jan 1, 2003

By Hong Liang-shi

Olivine lithium iron phosphate (LiFePO4) is considered as one of the most promising materials for lithium-ion secondary batteries because of its high theoretical capacity, low cost, good safety, benign environment and good cycle performance. In this paper, carbon-free and/or carbon-coated olivine lithium iron phosphate composite ultrafine powders were successfully synthesized from aqueous precursor solutions of (NH4)2Fe(SO4)2?6H2O, H3PO4 and LiOH?H2O by co-precipitation method. The obtained LiFePO4 or LiFePO4/C powders were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Their electrochemical performance was investigated in terms of cycling behavior. As confirmed by X-ray diffraction and scanning electron microscope, the material obtained by co-precipitation within the temperature range of 60ºC to 100ºC and then followed by moderate heat treatment are a single-phase olivine LiFePO4with the particle size of about 300nm. An improved carbon-coated olivine LiFePO4/C material was prepared by adding conductive carbon materials, such as glucose, activated carbon and acetylene black, into the precursor. The carbon dispersed in the materials increases the electronic conductivity of LiFePO4/C composite, and consequently, leads to high rechargeable capacity of the material. The carbon-coated material with carbon amount of 7.64%wt obtained from glucose has the first discharge capacity of 150.3mAh/g at the rate of 0.1C and 129.3mAh/g at the rate of 1.0C, respectively. After cycled for 50 times, the capacity retention rate is 95.13% at the rate of 1.0C in the voltage range of 2.5 to 4.3 V vs. Li/Li+.

Jan 1, 2006

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By Mohamed Y. Bakr, Aly M. Abdel-Rehim

The present work is related with mechanical activation of processing of Egyptian wolframite by simultaneous ball-milling and pressure alkaline leaching, to improve the recovery of tungsten from wolframite. The results show a total recovery of tungsten from wolframite (97.8- 98.7%) by simultaneous ball–milling and alkaline leaching at temperature 175-200oC. It is concluded that processing of wolframite by simultaneous ball- milling and leaching is mechanically activated and accelerated as a result of the grinding action of steel balls that caused the immediate rupture by continuous removing the product layer of the reaction ( sodium tungstate and iron and manganese hydroxides ) from reacting particle surfaces. This leads to the exposing of fresh and activated wolframite particle surfaces to alkaline leach solution and consequently the acceleration of the reaction of wolframite leaching .The results of the kinetic study 0f alkaline processing of wolframite and its mechanical activation show that the system is under kinetic control.

Jan 1, 2015

By A. J. Meir, Paul G. Schmidt

"We present a novel approach to the mathematical analysis and computational simulation of fully three-dimensional, nonlinear, viscous, incompressible MHD flow in complex configurations involving several liquid and solid conductors. Such configurations arise in numerous metallurgical processes. Employing the current density rather than the magnetic field as the primary electromagnetic variable, it is possible to avoid artificial or highly idealized boundary conditions for electric and magnetic fields and to account exactly for the electromagnetic interaction of the flow region with the surrounding space. In addition, the approach lends itself naturally to finite-element based discretization techniques. As an application, we simulate the stationary flow of an electrically conducting fluid around a solid spherical particle of arbitrary conductivity, in the presence of crossed uniform electric and magnetic fields, and compute the Lorentz, pressure, and viscous forces exerted on the particle. This problem arises in connection with the electromagnetic filtration (purification) of molten metals before the casting stage.IntroductionNumerous metallurgical processes are governed by MHD effects resulting from the macroscopic interaction of liquid metals with applied or induced currents, electric and magnetic fields. Frequently these effects are technologically exploited in order to drive or to control the flow of metallic melts. Typical examples include the electromagnetic stirring of molten metals before the casting stage [1]; electromagnetic turbulence control in induction furnaces [2]; electromagnetic damping of buoyancy-driven flow during solidification [3]; and the electromagnetic shaping of ingots in continuous casting [4]."

Jan 1, 1999

By Kaixi Jiang, Lei Zhang, Sanping Liu, Yufang Wang, Xiaoping Zou

"Molybdenite concentrates are usually treated by roasting, but low concentration SO2 pollution is a problem. Extraction of molybdenum and rhenium from molybdenite concentrates with a pressure oxidative leaching (POX) and solvent extraction (SX) process was studied. A series of POX-SX laboratory and pilot tests were carried out on the molybdenite concentrate. In the POX stage, more than 95% rhenium and 15-20% molybdenum were leached into solution. Solvent extraction recovered the rhenium and molybdenum from the POX solution. The extraction rates of Re and Mo were above 98%. The loaded organic reagent is stripped with ammonia. The stripping ratio of Mo is more than 98%. Compared to the roasting process, the total recovery of Mo increased from 93% to 97%, and Re from 60% to 90%. In the coming five years, POX-SX technology will be competitive in China.IntroductionMolybdenite is the main resource for the production of molybdenum, and about 99% of the total molybdenum was extracted from molybdenite. Rhenium is one of the important new materials in national defense, space flights, nuclear energy and electronics, because of its high melting point, high strength, plastic properties and significant creep resistance. There are no single rhenium ores in the world; rhenium mainly co-exists with molybdenum. Consequently, molybdenite is also the main resource for the extraction of rhenium."

Jan 1, 2012