Search Documents

By P. N. Anyalebechi

"The as-cast microstructure of two commercial-size ingots of aluminum alloy 3004 produced by the electromagnetic casting process was quantitatively characterized. This involved the quantitative determination of through-thickness and across-width variations in dendrite cell size, grain size, macrosegregation of alloying elements, interparticle spacing, and the types, volume fractions, and sizes of the constituent or second phase particles. More than ninety-five percent of the constituent phases in the ingots consisted of the A16(Mn,Fe) phase; the desirable a-Al 12(Fe,Mn)3Si phase was not detected in any of the ingots by Guinier X-ray diffraction analyses or electron probe X-ray microanalyses. A significant microstructural heterogeneity through the thickness and across the width of both ingots was observed. For example, macrosegregation, and the sizes of the constituent phase particles, dendrite cells, and grains increased concomitantly from edge to mid-width and from surface to center of the ingots. There was a -20% depletion (negative macrosegregation) of Mg and a +54-87% enrichment (positive macrosegregation) of Ti in the center of the ingots. With the exception of grain size, there was no significant microstructural difference between the two ingots examined. The causes and practical implications of the observed microstructural heterogeneity in the ingots are discussed.IntroductionThe first step in the fabrication of majority of wrought products of aluminum and its alloys is the casting of large ingots or billets of simple shapes (round or rectangular). The sizes of the ingots vary from 10 mm to 450 mm diameter or 25 mm to 780 mm thick. The quality of the finished products is established at the ingot casting stage. This is because the microstructural characteristics, such as secondary dendrite cell size or arm spacing, amount of alloying elements retained in solid solution, macrosegregation, and the characteristics of second phases, produced during casting cannot be reversed by subsequent processing. Up until twenty-five years ago, the effect of as-cast microstructure of large ingots on the structure and behavior of thin sheets (0.34 mm thick) during drawing and ironing processes was incorrectly assumed to be minimal or nonexistent. This was based on the erroneous notion that the thermal treatments and large reduction (>99.94%) and strain that the ingot undergoes during production of the sheets completely destroys the original ingot structure and its inherent heterogeneity. However, the effects of ingot structure can, a priori, be deduced from the observed effects of constituent phase particle size, type and volume fraction on recrystallization, development of texture during annealing and deformation, and earing. In fact, careful examination of the behavior of products produced from different size ingots or castings have shown that the original microstructure of the ingot has a direct impact on the properties and performance of the end products."

Jan 1, 2011

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

Cuspidine (3CaO?2SiO2?CaF2) is one of the most important compounds crystallized in mold flux films during casting in the continuous casting process of steel. The primary crystallization field of cuspidine has been experimentally developed in the CaO-SiOrCaF2-SiF4 system. The cuspidine-NaF binary and cuspidine-CaF2-NaF ternary systems have been also experimentally determined to study effects of addition of NaF on the primary field of cuspidine. In order to discuss its thermodynamic stability the standard Gibbs energy of formation of cuspidine has been determined by an electromotive force method using CaF2 as solid electrolyte and a transpiration method as follows: The chemical potential diagram and constituent activities for the CaO-Si02-CaF2 system have been evaluated based on the obtained thermodynamic data.

Jan 1, 2003

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By Metehan Erdogan, Furkan Özdemir, Ishak Karakaya, Mustafa Elmadaglı

Tungsten is mainly produced by H2 reduction of WO3 which makes its production difficult and costly. A promising method was recently reported for direct electrochemical production of tungsten from CaWO4 (scheelite) which is estimated as the seventy percent of the all tungsten reserves of the world. This paper investigates the application of pulse current in the electrochemical reduction of CaWO4 pellets attached to a current collector. The electrolyte was composed of calcium chloride and sodium chloride salts at eutectic composition (48 pct mol NaCl at 873 K). The reduced samples were cleaned with dilute hydrochloric acid solutions and characterized by X-ray diffraction and scanning electron microscopy. Examination of the results revealed that metallic tungsten was obtained by pulse current reduction.

Jan 1, 2016

By O. G. Rivera, R. D. Moser, P. G. Allison, W. R. Whittington, P. Rivera-Soto, Z. McClelland, D. Francis

This research examined the evolving microstructure of quasi-static and dynamically loaded fully annealed metastable 301 austenitic stainless steel (SS). Experiments were performed to an interrupted strain value of 20% and to failure using a tension Kolsky bar (1000/s) and an electromechanical load frame (0.001/s). Electron Backscatter Diffraction (EBSD) identified the microstructural evolution from the as-received condition to the 20% strain level for the high and low rate interrupted samples. This material achieved over 60% elongation to failure with increasing strength as strain rate increased, as expected. Fractography analysis using SEM showed particles in the microstructure and a ductile failure mode. The 301 SS exhibited a greater amount of phase transformation from parent austenite to -martensite at the dynamic strain rate when compared to the quasi-static strain rate during the interrupted experiments. This result is indicative of the increased propensity for austenite to -martensite phase transformations at the high strain rate.

Jan 1, 2016

By João M. S. Rodrigues

The use of sandblasting as a treatment method for conditioning anodes for zinc electro-winning was investigated and compared with conventional fluoride preconditioning. The anodes were made from two different lead-based alloys (Pb-Ag-Ca and Pb-Ag). Laboratory results showed that sandblasting and preconditioning both minimize lead contamination in the zinc and sludge generation. Sandblasting was found to have no aggravating effect on the anode corrosion. The sandblasting treatment was tested on Pb- Ag-Ca anodes on an industrial scale in the celJhouse of a local zinc producer. An unexpected finding of the large-scale tests was that the sandblasting appeared to strengthen the anodes, resulting in reduced warping during handling and operation.

Jan 1, 1996

By Antoine Allanore, Guillaume Lambotte, Bradley R. Nakanishi

Current industrial methods used for rare earth element (REE) extraction involve: 1) ore enrichment, 2) separation of rare earth oxides (REOs), 3) chlorination or hydrofluorination, and 4) individual electrowinning of REEs from a molten halide electrolyte. The complexity of REE extraction is inherited from their electronic configuration. Recently, molten oxide electrolysis (MOE) has been used to produce reactive metals directly from their oxides, e.g. titanium. As a single-step alternative to processes 3) and 4), or laboratory has investigated rare earth extraction by MOE. A key challenge is to find a molten electrolyte more stable than REOs. One possibility is to use binaries of REOs directly as a solvent. We have, therefore, developed two experimental approaches for studying molten REOs at temperatures exceeding 2200oC. The present work reports the most recent experimental results obtained with La2O3-Y2O3. Those promising results demonstrate potential for operating with molten REOs and refine the underlying materials challenge for electrodes to enable metal recovery.

Jan 1, 2015

By V. G. Papangelakis

The implementation of a flow-through yttria-stabilized zirconia (YSZ) sensor for pH measurements in high temperature and concentrated electrolyte systems relevant to hydrometallurgical processing of nickeliferous laterites is discussed. Instrumentation involved the use of a custom made flow-through titanium electrochemical cell. Accuracy and validity of the pH measurements at temperatures up to 250C were assessed using concentrated sulphate process solutions ranging from synthetic binary sulphuric acid ? water solutions to progressively multicomponent metal ? sulphate solutions simulating laterite Pressure Acid Leach conditions. The measurements were also compared with theoretical models using recently obtained thermodynamic data. A difference of ±0.25 pH units was observed between measured and calculated pH values at temperatures. This is an acceptable difference given that these are the first direct high temperature pH measurements ever on the concentrated acidic sulphate solutions. This result is encouraging more research for the development of industrial electrochemical systems for direct pH measurements in autoclaves.

Jan 1, 2003

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993

By James A. Voigt

"The efficient separation of metal species from aqueous streams by precipitation techniques requires a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems. The effects of solution chemistry, precipitator design, and solvent choice are considered.IntroductionThe application of precipitation technologies to the separation of metals from solution is widely used. Regardless of its application, be it in such diverse areas as the preparation of metal oxide powders for use in commercial products or as a unit operation in the removal of trace metals during wastewater clean up, the fundamental processes involved are the same. These processes include: nucleation from solution, either homogeneous or heterogeneous; growth from solution with chemical reaction either in solution or at the precipitate/solution interface; growth by particle agglomeration; and particle break-up by collisional or shear forces. The effectiveness of the operation and the properties of the precipitate formed, or ""quality"" of the product, are determined by the competing kinetics of the different processes. The kinetics of the processes, in tum, are determined by system-specific solution chemistries and the conditions used to carry out the precipitation operation. For example, generally, when system conditions are such that the supersaturation driving force for precipitation is very high, growth species normally do not have the time to organize themselves with a high degree of crystallographic order and the precipitate is amorphous. In this case nucleation rates are invariably extremely high and the primary mechanism for growth is the agglomeration of nuclei. Conversely, when the supersaturation levels for the same system are reduced, the kinetics of the nucleation and growth processes also are greatly reduced, and a crystalline precipitate can be formed, since the growth species have time to order on particle surfaces."

Jan 1, 1996

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

By T. K. Mukherjee, C. K. Gupta

"The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids, plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc .. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction playa pivotal role.This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge (2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, which influences the metal recovery process significantly, has drawn a special emphasis. In the case of refractory metals, basic extractants like Alarnine 336 has been pressed into service to produce kilogramme quantities of pure salts of molybdenum and vanadium. Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using a solvent system comosed of DEHPA and TOPO."

Jan 1, 1996

By V. B. Telles, J. A. S. Tenorio, J. O. Alves, D. C. R. Espinosa

"The world production of crude steel in 2009 reached 1.2 billion tons. For each ton of steel produced, 150 kg of steelmaking slag and 20 kg of steelmaking dust are generated. These are wastes with considerable production and limited applications, therefore this work studied the recovery of these wastes into useful sub-products. The slag was used as raw material in the production of rock wool (a thermo-acoustic insulator) and the dust was inserted in the iron ore sintering process. Results showed that produced materials have exceptional proprieties, therefore the recovery of these wastes can contribute to decrease extraction of non-renewable resources, reduce the costs and impact of disposals, and aggregate value to the slag and dust.1. IntroductionSteel production using Eletric Arc Furnace (EAF) has grown over 119 million tones in the last years. In 2008 30.7% of all steel produced, was obtained through EAF. In United States of America (USA) the percentage of this process in the production of steel was about 58% in 2008, while in 2000 this percentage was only 47% [1]."

Jan 1, 2011

By T. K. Mukherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effuents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic, byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By K. L. Money, R. R. Bleakney, R. H. Hanewald

The processing of EAF baghouse dusts, rolling mill scales, and belt grinding swarfs from the specialty steel industry will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions, filter cakes, spent nickel and chromium plating baths, super alloy wastes, and nickel-cadmium batteries. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery.

Jan 1, 2000

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003