Search Documents

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By E. Krystad, G. Tranell

"The kinetics of boron removal from liquid silicon during slag refining, as a process step in the production of solar grade silicon, has been investigated by means of small scale mass transfer experimental series at 1600°C, using a graphite crucible. The slags were SiO2-CaO based, with or without addition of approx. 19 wt% MgO. Experiments were carried out at slag-metal ratios of 1 or 2, where the silicon initially contained approx. 250 ppm boron. The metal-slag mass transfer coefficients for boron were found to be in the order of 1-3 · 10-6 m/s and were largely influenced by slag composition. The mass transfer rate was higher for the MgO-containing slag than the slags without MgO. The final equilibrium distribution of boron between metal and slag, LB, was determined to be in the order of 2.3-3.3.I. INTRODUCTIONRecent years have seen a race in industry and research aimed at obtaining a reliable metallurgical route for production of silicon for solar cells (SoG-Si) from metallurgical grade (MG) silicon. Metallurgical routes can successfully challenge the traditional chemical routes for production of SoG-Si if they generate metal of sufficient purity while being less expensive in terms of production cost and energy consumption. Efficient removal of boron is one of the greatest obstacles in the refining of silicon by a metallurgical route, because the segregation coefficient of boron in silicon makes directional solidification unfeasible; in addition, the vapour pressure of boron is not high enough for removal by vacuum refining. However, the thermodynamic properties of boron makes removal from silicon by oxidation possible, and thus the process of slag refining of silicon has been receiving increasing attention as a method for boron removal."

Jan 1, 2012

By Michel Boisvert

Noranda Metallurgy is presently completing construction of the new Noranda Converter (NCV) at its Home Smelter in Rouyn-Noranda. This capital investment of CDN$56M is the continuation of the Emissions and SO2 Reduction Program that was initiated in the late 1980s with the acid plant for Reactor off-gas treatment. The Patented Noranda Converter was developed and pilot tested at the Home Smelter in the early 1990s. The project will replace the Peirce-Smith Converters and enable sulphur fixation to be 'increased from 70% to over 90% by 2002 with an accompanying reduction of dust emissions to the atmosphere. The construction site is an extension of the present Noranda Reactor area. A number of existing facilities including the acid plant and process air supply were used to minimize the capital cost of the project. This paper provides a brief history of the Noranda converting process, the Home Smelter Emissions and SO2 Reduction Program, ,project implementation and construction, a description of the different facilities, and preparation of human resources for start-up.

Jan 1, 1998

By Sergey Shabala

Green leaf tissues convert solar energy into the energy of chemical bonds of sugar molecules during the process of photosynthesis. The efficiency of this conversion can be much higher than efficiency of any of the currently known silicon-based solar panels. Importantly, vast amounts of CO2 are assimilated during this process. The efficiency of photosynthesis is critically dependent on the availability of a large number of nutrients, among which metal cations such as K, Ca, Mg, Cu, Zn, Fe, Mn, and Ni play a key role. In this paper I summarize basic requirements and major functions for each of these essential nutrients in plant photosynthesis, both at the whole-plant and molecular level. I will talk about how these requirements may be affected by the global climate trends and discuss the prospects of creating artificial photosynthetic “bioreactors” for efficient energy conversion and CO2 assimilation.

Jan 1, 2009

By Jun Li, Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial of direct modification of molten blast furnace slag and production of high acidity coefficient slag wool fibers were investigated nearby a blast furnace. Molten blast furnace slag discharged from blast furnace and then directly flow into specialized modification furnace and quartz was simultaneously added into the molten slag as modification agent. The modified molten slag was electric heated to 1500–1550 °C and then the melt was produced into slag wool fibers through high-speed centrifugation method. Melt with acidity coefficient of 1.2, 1.4, 1.6 and 1.8 were investigated and fibers with corresponding acidity coefficient were produced. Slag wool fibers with shot content of 5.5, 5.8, 6.2, 6.8% and average diameter of 4.5, 4.9, 5.6, 6.4 lm for four samples were successfully produced, respectively. Total energy consumption and production costs decreased by 50–70% compared to traditional cupola furnace method. This method provides an energy-saving and emission-reduction technology for the direct utilization of molten blast furnace slag.

Mar 1, 2018

By B. M. Satish

The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200°C) for 1 hour followed by slow cooling (120°C/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000°C. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.

Jan 1, 2009

By Guoqiang Lv, Xi Yang, Wenhui Ma

Cast multicrystalline silicon ingots are widely used in photovoltaic manufacturing. A key issue to achieve high solar cell efficiencies is to attain an optimized temperature field during directional solidification (DS) process. This paper reports numerical investigation of multicrystalline silicon (mc-Si) ingot production using two major types of DS furnace. Specific examination is made on thermal distribution, interface shape and stress field. Evaluation is performed for the applicability of thermal system design to reduce thermal stress, improve crystal quality and enhance energy efficiency. The effects of procedure parameters and geometric configuration on temperature distribution are discussed as well to provide the viable solutions for systems optimization.

Jan 1, 2015

By Terence Makanyire, Animesh Jha

The dissolution and chemical properties of vanadium, zirconium, and niobium in rutile lattice are analyzed by comparing the octahedral site preference energies, with respect to Ti4+ ion in the solvent phase. The oxides are often present in rutile lattice and interfere in achieving the quality of pigment grade TiO2 due to favourable Gibbs energy for dissolution in the solvent rutile matrix. Binary mixtures of V2O5 { TiO2; Nb2O5 { TiO2 and ZrO2 { TiO2 with compositions of 80, 85, 90, 95 and 97 wt% TiO2 were made, pelletized and sintered at 1100 °C for 24 hours. The solidsolution mixtures were then cooled and leached in 2M NaOH for 3 hours at 60 °C. Phase and lattice parameter characterizations, and microstructural and compositional analyses were then carried out using X-ray diraction and SEM/EDX, respectively. The leachates were analysed by Atomic Absorption Spectroscopy (AAS), using which the solute dissolution model for oxides were investigated.

Jan 1, 2014

By Barry Welch, Kai Grjotheim

"The capital intensive nature of the present process for aluminium smelting, the low productivity per unit reactor, and pressure to reduce the electdcal energy demand have motivated the search for an alternative process. Optional routes include carbo-thennal reduction of alumina (using an alloy phase immediate), chlorination followed by electrolysis of aluminium chloride, and electrolytic decomposition of alumina using inert electrodes. Materials performance and reactor design constraints have been a major limitation for alternatives. However parallel research has led to considerable advances in the process efficiencies and scale of both the Bayer process and the Hall-Heroult cells.Future development of alternatives is dependent on breakthroughs in Materials Science such as the development of stable conducting anodes and stable wettable cathode materials. However if successful it is probable that some spin-offs will be retrofitted to existing cells. Therefore the basic Hall-Heroult technology will continue as the dominant process for at least the next half century.IntroductionThe present Bayer/Hall-Heroult process for production of aluminium is just over 100 years old. Frequently, during the century of its technological development questions have been raised as to whether it is the ideal route for metal production. The questioning was particularly intense in the period between the mid-1950s and the mid-1060s when the limitations of the Hall-Heroult electrolytic stage were evident. Then the cells were only 30 to 35 % efficient with respect to the utilisation of the hydro-electricity (requiring 16 18 kWh/kg, thus making it strongly dependent on cheap electrical energy), while the size of cells being installed were 80 to 130 kA. Hence the process was capital intensive, the productivity per reactor volume low, and the process was labour intensive (requiring about 15 man hours per tonne of aluminium). In addition, the use of pitches for Soderberg anodes and the fluoride electrolyte were creating problems through emission. At that time material science had paid little attention to the manufacture and use of carbonaceous materials or the development of alternatives that were corrosion resistant to cryolite or liquid aluminium. Hence cell lives were short - typically 600 to 1000 days - thus adding to operating costs. Thus the grass over the fence, as foreseen in 1960s vintage crystal balls appeared much greener for alternative processes."

Jan 1, 1988

By S. Stoyanov, M. Cross

"Silicon components containing transistor circuitry are at the heart of electronic products such as computers, mobile phones, etc. These components are connected to printed circuit boards (PCB's) using solder material that acts as the conductor for both electricity and heat. During the lifetime of a product it will undergo many thermal cycles where the chip becomes hot during product operation and then cools when the product is switched off. At the product design stage engineers undertake thermo-mechanical simulations to predict the thermal stress in the solder joints due to this thermal cycle and to ensure that the stress magnitude will not result in early fatigue-type failure. The design engineer's aim is to identify component parameters which ensure that the solder will survive beyond a certain number of thermal cycles.The aim of integrating computational mechanics and optimization tools together is to speed up dramatically the design process. From viewpoint of a design engineer in the electronics manufacturing sector, these tools can be used to quickly estimate key design parameters (i.e. material properties, product dimensions, etc) that will guarantee the required product performance. In this paper a modeling approach coupling computational mechanics techniques with numerical optimization is presented and demonstrated. The integrated modeling framework is obtained by coupling the multi-physics framework - PHYSICA - with the design optimisation tool- VisuaLDOC. Thermo-mechanical simulations are presented that predict the creep strains in solder material. Different numerical optimization procedures: Direct and Response Surface based optimization plus Design of Experiments, are tested as a part of this modeling framework."

Jan 1, 2001

By Ian F. Hughes

"Concepts of an integrated steel plant for sheet products to be built and operating in the year 2000 will be described. The design and operating methodology of this market driven facility will integrate process uniqueness, standardization, manufacturing automation, artificial intelligence and information flow.An integrated steel plant for the year 2000 is defined for this article as one that will be built on a greenfield site and ""started up"" in the year 2000 with a capacity of three million tons per year of flat rolled products ranging from cold rolled and electrical steels to high strength formable steels and a full range of coated products.It may seem that the 21st century and the steel plant we're discussing are far into the future. The startling truth, however, is quite the opposite. As shown in Figure 1, even with accelerated development, a new process on which laboratory development work is begun today might just barely pass through the laboratory phase, pilot plant, and commercial feasibility stages such that it can be considered viable for construction and start up in the year 2000.On that basis, it is very unlikely that this 21st century steel plant will utilize any technology that isn't at least under investigation in the laboratory in 1988. As a result, we recognize that planning and selecting the facilities for this plant is, in fact, a pragmatic rather than futuristic process, and that its main value is in providing a bridge to longer-term predictions."

Jan 1, 1988

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"To determine the heating rate of billets using ‘short coils’, an appropriate correction factor must be applied to the theoretical relationship. In 1945, Vaughan and Williamson published a semi-empirically modified Nagaoka coefficient applicable for moderate frequency induction heating processes (10 kHz). Recently it was demonstrated that the method of Vaughan and Williamson gives <10% error in the estimated power when heating aluminum billets at 50 Hz.In the present study, experiments have been conducted on aluminum billets in order to verify an empirical frequency corrected ‘short coil’ equation. Measurements of electrical conductivity (<± 0.5%), current (± 1%), heat (± 1-3%), and magnetic flux density (± 1-2%) have been performed. The results are compared with 1D analytical calculations, and 2D axial symmetric FEM modeling using COMSOL 4.2®. The frequency corrected equation has proven to provide accurate predictions of power (<4% error) within the frequency range 50 Hz to 500 kHz.IntroductionInduction heating is commonly applied to the re-heating of billets before forging or extrusion processes. The resistive heating produced by eddy currents in the solid or semi-solid work piece during this procedure, is driven by the time varying magnetic flux density in the air-gap between the work piece and the coil. The flux in the air-gap is created by the current flowing in the induction coil, i.e. the magneto-motive force. In Figure 1 it can be seen that the currents present in the work piece are concentrated in the outer ‘shell’, or the first electromagnetic penetration depth (dw), and flow in a direction which opposes the magnetic field produced by the induction coil."

Jan 1, 2012

By E. Salinas R.

This work is related with a whole characterization of cantera stone, to establish its characteristics that can give it an additional value for the reuse and reutilization of dust, slurries and small pieces of stone which can be treated as wastes. The obtained results reflects that the residues studied can be used as substitutes of feldspars in the production of pieces of ceramic, and also in the elaboration of paints for the same pieces according to the mixes that can be made with the variation of Na2O, CaO and K2O. According to the humidity proofs and specific gravity done, this material can be proposed as a soil improver into hydroponics systems, leading so an important alternative for food production in zones leaking of water. In the same way, it was found the possibility of use this material as a seal 3A in processes of asphalting of roads, highways and streets.

Jan 1, 2009

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By S. K. Kawatra, T. C. Eisele

"Recent advances in microbiology have made the application of biotechnology to metallurgical processes possible. Hydrometallurgy stands to gain the cost from the use of microorganisms, as they are useful for both dissolution aids and for removing metals from solution. The development of genetic engineering techniques promises to greatly increase the importance of bioprocessing of metals and minerals by the year 2000.In this paper, the basic effects of microorganisms on metallurgical processes are reviewed, and the applications which are currently either in use or near being used are presented. Representative data collected at Michigan Technological University is also given.IntroductionMany hydrometallurgical operations exist which are thermodynamically possible, but which are industrially impractical due to slow kinetics, high reagent costs, or the need for a highly corrosive environment. However, recent discoveries in microbiology indicate that in many cases these difficulties can be reduced greatly by the action of bacteria and other microorganisms (1-8).A major advantage of using living organisms in hydrometallurgy is that once the culture is established the microorganisms produce their own reagents either from the material being processed or from low-cost nutrient supplements. They thus allow extremely complex chemical reactions to be carried out at reasonable cost. The major drawback of using microorganisms is their inability to tolerate extremely high temperatures, excessive concentrations of toxic metals, or very highly acidic, alkaline, or corrosive conditions. However, the complex reactions which bacteria make possible frequently eliminate the need for such extreme conditions. Also, in recent years a number of organisms have been isolated from such exotic environments as hot springs and deep-ocean vents which can tolerate temperatures higher than was previously thought possible for any organism, and can catalyze a number of metallurgically important reactions (8)."

Jan 1, 1988

"Mixing phenomena in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor was studie9-using three different configurations of straight circular nozzles fitted axially at the bottom of the vessel. The mixing time has been determined by pH measurements at various gas flow rates, bath heights and nozzle orientations in the presence and in the absence of a second phase.Experimental results reveal that the mixing time decreases with increasing gas flow rate. For a given gas flow rate the mixing time increases non-linearly with increasing bath height. Off-center configuration gives slightly lower mixing times as compared to center configuration. It is found that the contribution of buoyancy to the total stirring energy density is very small, but its contribution increases with increasing bath height. In the presence of an upper oil layer, the mixing time increases significantly for all configurations.IntroductionIn high temperature metallurgical melts mixing is carried out by injection of a gas either from top or bottom of the vessel in order to accelerate the rates of chemical reactions and to promote bath homogenization. When a gas is injected into a liquid through a submerged lance, porous plug or nozzle, the gas, rising as a two phase plume to the surface, imparts momentum to the surrounding liquid and causes gross circulation in the bath which promotes mixing."

Jan 1, 1997

By C. A. Young

The remediation of cyanide (CN-) and nitrate (NO)-) anions in mine and agricultural waters by various photolytic methods has been reviewed and investigated. Photolytic methods such as direct photolysis, homogenous photolysis, and heterogeneous photocatalysis are briefly described and compared. Results and discussions show that each method has certain advantages and disadvantages. For each method, Eh-pH diagrams prove useful for determining reaction mechanisms. Preliminary results obtained for cyanide oxidation and nitrate reduction show that homogeneous photolysis can be superior due to faster kinetics than the other methods. The photolytic methods were individually, not simultaneously, tested and compared. Differences in concentrations of products were obtained and attributed to differences in photoconversion efficiencies and other inherent characteristics of .the photolytic methods. Various reaction mechanisms are proposed in accordance with the literature as well as measurements obtained from solution analysis using ion selective electrodes and ion chromatography .

Jan 1, 1995

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006