Search Documents

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By Jasper Kwong

The recycling of MgO-C refractories as a slag conditioner in EAF (electrical arc furnace) foaming slags have been evaluated by the Albany Research Center. The amount of MgO in the slags is critical for the foaming quality. Good foaming slags provide the benefits of high energy efficiency and low refractory consumption and require saturation with MgO. A computer model predicting the chemistry of MgO saturated foaming slags was designed to predict suitable amounts of MgO additives from MgO-C spent refractories. This model can also help to reduce the amount of slags and to improve the economics of producing steel. The implementation of this recycling program is underway at steel plants and the experience of recycling spent refractories will be discussed.

Jan 1, 2002

By Ramona Prillhofer

Salt slag is a waste product produced by the recycling of aluminum. In most European countries (e.g. Austria, Germany) the landfill disposal of this waste is forbidden because the slag contains soluble salts and these represent a potential source of pollution to the surface and groundwater. Additionally, consisting metal and some compounds in the salt slag can react with water and resulting from this, noxious gases are generated. The recovery of useful materials from these wastes is accordingly both environmentally necessary and economically feasible. This study describes a complete recycling-process for the salt slag, which includes a leaching-cristallization-process to obtain the oxidic residue, a pyrometallurgical-step to clear the oxidic residue and finally an extensive characterization of the achieved products. Due to the increasing price of raw materials, the utilization of the oxidic residue into commercial products has been investigated and application possibilities will be discussed.

Jan 1, 2009

By Sue Ritz

Gold extraction has relied on coconut carbon in adsorption circuits for several decades. IXOS®, invented by 6th Wave Innovations of Salt Lake City, Utah, is a new type of adsorbent that exceeds the selectivity of carbon and improves on the mechanical properties of other available resins. IXOS selectivity against copper cyanide complexes allows it to be used in circuits that currently struggle with copper contamination. IXOS potential to eliminate or reduce the application of SART technology will expand the opportunities to exploit more complex precious metals deposits. This paper will describe the technology behind IXOS molecular imprint, its comparison to carbon adsorption in the field, and the effect of efficiency on long-term recovery from heap leach METSIM simulation software.

By Edward P. Hagarty

The Hazardous and Solid Waste Amendments (HSWA) of 1984 added Subtitle I to the Resource Conservation and Recovery Act (RCRA), authorizing the Environmental Protection Agency (EPA) to develop and implement a new regulatory program for Underground Storage Tanks (USTs) containing petroleum and other regulated substances. Technical standards required for release detection, prevention, and correction as necessary to protect human health and the environment were promulgated as described in 53 Federal Register 37082 (September 23, 1988). Virginia State Regulations (VR 680- 13-02) and U.S. Army Regulations require that a Corrective Action Plan and a Site Clearance Report be prepared to explain the details of remediation of any contaminated media. Construction of new buildings is proposed in two different areas at Fort Myer in Arlington, Virginia, where USTs containing gasoline, diesel and heating oil were located. Tightness testing performed on these USTs in September 1991 indicated that some of the tanks were leaking. Many of the tanks were removed for permanent closure. Initial Abatement (excavation of contaminated soil) was &ed out immediately. A detailed Site Characterization Study which included Hydropunch", field screening using immunoassay, and pilot test - dual phase (water and soil gas) extraction was conducted. Environmental media were analyzed for volatiles, semi-volatiles and metals. A detailed risk analysis (RA) was performed to determine risk-based clean up levels for benzene, toluene, ethylbenzene, xylenes (BTEX); polycyclic aromatic hydrocarbons (PAHs); and methyl-tertiary butyl ether (MTBE). The RA also discussed the presence of lead in the soil. Before constructing any buildings in these contaminated areas, remediation must be conducted in accordance with the State, Federal and other applicable regulations. The remedial alternatives evaluated included Vapor Enhanced Groundwater Extraction, Soil Vacuum Extraction, Soil Washing, Soil Steaming, Active and Passive Ventilation SolidificationlStabilization, Vapor Barrier Construction, and Excavation with Off-site Disposal. This paper discusses: (a) delineation of soil contamination @) risk analysis (c) evaluation of remedial alternatives and selection of the most appropriate technology and (d) consideration of various regulatory issues.

Jan 1, 1994

By Miguel Barron

Recently, a new lance design for BOF steelmaking has been proposed in the literature. This lance, in addition to six peripheral inclined supersonic nozzles, contains a vertical centered nozzle whose oxygen flow is independent from the main oxygen supply. The above authors affirm that their lance maximizes the droplet generation without causing spitting. In this work, the performance of a lance with four peripheral nozzles and one vertical centered nozzle is numerically modeled by means of Computational Fluid Dynamics software. Transient two dimensional computer simulations were carried out considering two phases, namely molten steel and gaseous oxygen. Numerical results confirm that bath agitation and droplet generation are enhanced as a result of the vertical centered nozzle, however a proper performance of this lance, related to a conventional one, strongly depends on the Mach number of the oxygen jets and the lance height.

Jan 1, 2008

By NRMR Bhargava

With the increasing use of lead-free solder alloys, low melting point alloy is often required due to the heat- sensitive parts or substrates in modern electronic devices. For such demand of low melting point, the nanostructure lead- free solder alloy, having excellent metallurgical characteristics and a melting point of <215oC, were developed by mechanical attrition of conventional lead free solder alloys (Sn-Ag-Cu, Sn-Ag and Sn-Cu). The decrease in melting point due to nanosize effect was calculated theoretically as function of particle size and the theoretical results were compared with experimental values measured by differential scanning calorimetry. The newly developed alloys have eutectic composition of Sn-3.5Ag-0.7Cu, Sn-3.5Ag and Sn-0.7Cu and the melting point depression found to be 5.10C, 4.10C and 6.20C when the bulk alloys reduced to 80 nm, 92nm and 96nm sizes respectively.

Jan 1, 2009

By T. W. Gonzales

The BHP San Manuel Smelter operates an Outokumpu Oy flash furnace, conventional Peirce-Smith converters, anode casting facilities, and two double contact sulfuric acid plants. The flash furnace was commissioned in July 1988 and since then, the smelting capacity has been continuously increased to 30% above design. The converter operation was challenged to process larger amounts of matte with existing capacity. Utilization of industrial technological improvements and people technology transformed the Converter Department from a constraint to easily accommodate the new demonstrated flash furnace capacity. This technology also increased secondary consumption, converter campaign life, and reduced operating costs. This paper will describe the important Converter Department achievements in the past five years.

Jan 1, 1999

By A. E. Torma

In recent years the copper industry has gained considerable economic stability. An essential part of this industrial wealth is attributable to the successful application of bio-mediated heap and dump leaching techniques in the recovery of copper from low-grade resources. This study evaluated the leachability of a chalcopyrite conlentrate using naturally occurring mixed culture of predominantly Thiobacillusferrooxidans and Thiobacillus thiooxidans. For the effects-of pulp density, the overall reaction rate constant (k) and the order of reaction (n) have been determined to be 1.93 h-1 and 1.36, respectively. Cyclic voltammetric measurements revealed that intermediate reactions are involved in the chalcopyrite oxidation. Using the Price approach, it was shown that the dissolution of chalcopyrite is solid state diffusion controlled.

Jan 1, 1992

By Khandaker M. Anwar Hossain

This paper presents the development of lightweight concrete (LWC) incorporating pumice aggregate and volcanic ash (VA) based ASTM Type I blended cement (PVAC). Fresh and mechanical properties of LWC mixtures such as slump, air content, compressive strength, tensile strength, density and modulus of elasticity are described. The durability characteristics are investigated by drying shrinkage (DS) and water permeability. The investigation suggests the production of LWCs incorporating blended PVAC and VPA having satisfactory strength/durability characteristics for structural applications. The use of PVAC induces the beneficial effect of reducing drying shrinkage and water permeability. Development of such non- expensive and environmentally friendly LWCs with acceptable strength and durability characteristics is extremely helpful for the sustainable development and rehabilitation of volcanic disaster areas around the world.

Jan 1, 2010

By Jianxin Zhang

A process, in which arsenic in the residue is transformed directly into scorodite and copper dissolves into the solution simultaneously, was studied. The process was carried out in acidic ferrous sulfate solution under oxygen pressure. The optimum conditions of the process were determined as follows: the initial H2SO4 concentration of 10 g/L; liquid/solid ratio of 10; Fe/As molar ratio in the feedstock of 1; the addition of calcium lignosulphonate was 1% of sludge; oxygen pressure, temperature and reaction time were 1.5 MPa, 150 °C and 6 h, respectively. Under these conditions, arsenic transformed to crystalline scorodite in size of 5–10 μm, and the transformation efficiency reached 97.60%; meanwhile, the copper was leached with a high efficiency of 93.34%. The stability of the leaching residue was evaluated by TCLP testing, and the results indicated the concentration of arsenic in the leaching solution was extremely low as 0.04 mg/L and met the standard of safe stockpile.

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By Ronald H. Church

Dewatering of mine waste slurries has been successfully accomplished by the proper use of polymers in flocculating the fine particulate matter suspended in the slurry streams. Conventional treatment of fine waste slurries usually involves some form of impoundment treatment or storage. These impoundments present unique environmental problems. When filled to capacity, the impoundments are usually unloaded with a dragline and transported to a separate disposal area. The U.S. Bureau of Mines has conducted dewatering studies utilizing polymer technology in combination with a mobile field test unit designed by the Bureau. The purpose of these studies was to determine if the fine waste slurry from the mining operation could be successfully dewatered. Results of the investigation have shown that the slurry can be dewatered successfully. The dewatered products obtained from the tests ranged from 45 to 50pct solids. This material continued to dewater, approaching 70 pct solids within 24 h, and could be easily handled using conventional transportation equipment including conveyor belts.

Jan 1, 1994

By Cyro Takano

An alternative use for recycling of waste from bag house of iron ore sinter plant was tested by producing and evaluating" at laboratory scale, the self reducing cold bonded pellets. This waste was characterized and the self-reducing pellets were produced using anthracite coal fines as reductant and Portland cement or hydrated lime/Blast Furnace slag as binder. It was used the molar ratio of Fe2O3/C (fix) equal to 3. Evolution of cold strength with curing time, for different contents of binder, was evaluated. Cold strength of 200N/pellet was obtained, for sinter dust, after 10 days of curing. Suitable hot strength was also presented and no decrepitation and swelling were observed. Good fractional reduction was obtained at 950°C and 1137°C. These results show that this material may be used by the Self-Reducing Processes for hot metal production, as an alternative route for this dust destination.

Jan 1, 1996

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By K. Yamaguchi, Y. Takeda

"Partial pressure - temperature - composition correlation diagrams of the Ga-As, In-As, Ga-P and In-P systems were contracted based on the obtained experimental data of the phase diagram and thermodynamic properties for the III-V systems. The total vapor pressures of arsenic or phosphorus at melting point of GaAs, InAs, GaP and InP were determined as 101, 10.1, 1510 and 253 kPa, respectively, at the corresponding melting points of 1509, 1211, 1739 and. 1336K , These diagrams are applied to the analysis of the horizontal Bridgman method and the liquid phase epitaxial growth technique. On the other hand, the analysis of the equilibrium state of the. chloride-CVD process was carried out using the data of the Gibbs energy of the compounds obtained by· authors.IntroductionThe group III-V compound semiconductors ate important materials used in optoelectronic liquid high speed electronic device. The crystal growth of the III-V compounds can involve processes that require contact between the solid, liquid and vapour phases at near equilibrium condition. Examples of processes that involve contact between the solid, liquid and vapour phases include bulk crystal growth such as the horizontal Bridgman and the liquid encapsulated Czochralski method and liquid epitaxy, and between the solid and vapor include chemical vapour deposition and molecular beam epitaxy. Therefore, the knowledge of the phase diagram and thermodynamic properties for the III-V binary alloys is essential for the analyses of crystal growth techniques of III-V compounds.For these reasons, a series of different · types calorimetric measurements had been carried out: (1) The heat contents of alloys for the Ga-As, In-As, Ga-P and In-P systems by a drop calorimeter [1;2,3]; (2) the heats of formation of the GaAs, InAs, GaP and InP compounds by a twin solution calorimeter [4]; and (3) the standard entropy of these compounds by an adiabatic calorimeter [5]. Based on the third law method, the Gibbs energies of these compounds were derived from the heat capacity, standard heat of formation and standard entropy data obtained by authors. Integral molar thermodynamic quantities of the liquid III-V .alloys were also determined from combining the heat contents of alloys with standard heat of formation and standard entropy data of the compounds· by applying the thermodynamic analysis method developed by Oelsen [6]. In the present study, the thermodynamic calculations for the crystal growth processes of the III-V compound were carried out using newly experimental data of the phase diagram and thermodynamic .properties measured by authors"

Jan 1, 2000

By E. M. Alcântara

This paper describes some aspects about the relationship between copper electrorefining addition reagents and the hydrogen in the cathode. The conditions of electrorefining were studied by factorial design methods. The advantages of this technique are reduction in the number of tests, well organized experiments; improvement in productivity and reliability of results. The dosage of the two main addition agents, glue and thiourea, were varied simultaneously and compared with the hydrogen content in the cathode. The influence of these factors, as well their interactions were analyzed by statistical methods denominated ANOVA (Analysis of Variance). The increase of thiourea quantities, within of levels studied, influenced significantly at 95% confidence in the hydrogen content in copper cathode.

Jan 1, 1999