Search Documents

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in a flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the predicition of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace. The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Igor Zh. Bunin

A model for developing electric discharges between sulfide mineral (pyrite) particles under high-voltage nanosecond pulses in a liquid medium (water) is considered. A possibility of electrical breakdowns of liquid gaps between particles under nanosecond pulses is shown. This probability and the energy released in discharge channels depend strongly on the sulfide conductivity.

Jan 1, 2010

By Sadegh Firoozi

Experiments measuring the kinetics of oxidation and making visual observations of the oxidation of approximately 6 g static lead baths containing arsenic, antimony and tin were conducted in the temperature range from 500 to 600 oC. A range of repeatable behaviours were observed, notably: the formation of a coherent, solid oxide layers on pure lead and lead-tin alloys; the formation of liquid oxide droplets during the initial oxidation of lead-arsenic and lead-antimony alloys and the eventual formation of a complete oxide layer covering the entire free surface of these alloys. Thermogravimetric measurements revealed that the rate of oxygen uptake was strongly influenced by the form of oxides being generated at the melt/gas interface. Compared to the rates of oxidation of pure lead, arsenic increased the rate of oxygen uptake throughout the temperature range via the formation of liquid oxidation products. The presence of antimony resulted in a moderate increase in the rate of oxygen uptake as compared to arsenic. Tin was effective in lowering the rate of oxidation even in the presence of arsenic because the oxidation product was always a coherent layer that acted as a physical barrier to oxygen transport to the underlying alloy.

Jan 1, 2006

By Michael J. McGuire

Rostoker, Inc. has developed a process to smelt solid hazardous/non-hazardous inorganic wastes. Near seven hundred experiments were performed. Actual industrial wastes as well as reagent grade chemicals were used. By mixing a multiplicity of these wastes to proper formulations, then furnacing them, it was determined that saleable end products could be reclaimed; metal, fume and slag. The slag, due to its siliceous structure was tested to be leach resistant (40 CFR). This formed the essence of our patent, #5,180,421 "Method and Apparatus for Recovering Useful Products from Waste Streams". What is unique is that a HTMR (High Temperature Metal Recovery) process has been developed that can treat a multiplicity of wastes within the same furnace. The discussion will include a list of waste streams we have treated, details of proper waste formulation and experimental results.

Jan 1, 1994

By D. Q. Cang, G. Duan, H. X. Li, H. Bai

"Life cycle assessment (LCA) is a valid environmental evaluation method and enterprise environmental management tool used in industrial ecology areas. In this paper LCA was newly used to evaluate the environmental impact of manufacturing of alumina by Bayer process in china from two aspects of logistics and energy flow, GaBi software acted as analysis tools with evaluation model established, and several environmental impact assessment criteria were selected based on the actually typical date of Bayer alumina producing process. Evaluation results show that alumina manufacturing by the Bayer process has a great impact on the global warming and human health of respiration, even roasting process gives rise to the greatest impact of winter fog index. Scenario analysis proposed ways of reducing environmental load caused by Bayer process including: (1) the economic and efficient use of mineral processing technology; (2) optimization of energy use, saving power consumption or the use of new more economical source of energy; (3) actively promote the use of innovated technology and equipment in alumina manufacturing and waste such as red mud utilization process.1 IntroductionSince 2002, China is already the world's biggest producer of aluminium, in 2007, China aluminum production has accounted for above 1/3 all over the world, 2009 for 13 million tons and to the end of 2010, China aluminum production is expected increased to be over 15 million ton [1,2,3]. While as the raw material for producing aluminum the alumina production in china has up to 19.46 million tons of the world's total quarter in 2007, by the end of 2009 China alumina production has achieve to 23.78 million tons [4,5]. China has rich bauxite resources with proven reserves about 23 million tons, but the great majority of china bauxite is hard monohydrate diaspore type with low ratio of aluminium silicon, high impurity content and poor aluminum dissolution performance, that cause high energy consumption, long and complex process, high production costs and heavy environment load[6,7]. Before most used alumina production was sintering process rather than Bayer method in china, over the past decade Bayer method has been widely applied instead of sintering process or combination both forming joint process, premise is improving bauxite quality by mineral processing or adding imported rich bauxite mineral[6,8]. In general each ton production of alumina needs bauxite 1.6~2.20t, limestone 0.7~1.7t, soda 0.250kg, fresh water 12.30 cubic meters, in addition to consume large amounts of energy, and emission waste water over 8.0 cubic meters, dust 2.3~5.7 kg, red mud 0.8-1.5 tons. In china Red mud yield nearly 30.0 million tons every year, accumulated stock is approximately 0.2 billion tons, by 2015 accumulative total red mud is expected to reach 0.35 billion tons [9-13].We know aluminium industry and alumina production have produced large waste, make large energy consumption and its environmental impact could not be ignored. Expecting to optimize production processes and achieve resource recycling for this industrial process the proper environmental assessment is very necessary. Currently Life Cycle Assessment (LCA) is generally recognized as the approved tool to achieve the purpose. The essence of LCA tool is to examine, identify and evaluate a kind of materials, product, process, or a system of environmental impact in their whole life cycle. The life cycle of materials or products includes whole process from raw materials obtained to the final disposal, or more ideal with original or other forms of the whole process of recycling [14-17]."

Jan 1, 2011

By E. A. van Dijk

Dusts from steel-making processes contain substantial amounts of zinc. Such dusts are also a hazardous waste and dumping them becomes unacceptable from environmental point of view. Therefore processes that can recover zinc and possibly other metals from steel-making dusts are being investigated. The aim of this paper is a contribution to the more fundamental kinetic aspects of zinc reduction from silica free calcium ferrite slags. The effects of alumina, lime and magnesium oxide contents of the slag, the COICO, ratio and the effect of initial Fe2O3/CaO ratio were studied experimentally at 1400°C The results indicated that the reduction of zinc from molten slag was possibly a first order reaction. As expected higher COICO, ratios increased both the extent and the rate of reduction. It was also observed that a higher iron content of slag improved the reduction of zinc from calcium ferrite slags. This fact seems to support the proposed mechanism that zinc is partly reduced by ferrous iron to zinc vapour and that ferric iron is reduced by carbon monoxide. The reduction rate of zinc in these slags was decreased by increasing alumina content of the slag. Alumina decreased the calculated optical basicity of the slag showing the fact that reduction of zinc oxide was more favorable in more basic slags. Probably the formation of complex ions by alumina and zinc oxide such as ZnAl2O32+ lowers the activity of Zn2+ ions in the slag and hence render them more difficult to reduce.

Jan 1, 1999

By Gordon Lewis

A complex mixture of hydrated reaction products is obtained from hydrothermally treated refractory cements and castable concretes. TGA can be used both to identify the product phases in the mixture and to determine a quantitative relationship among the phases. When reacted mixtures contain compounds that decompose simultaneously, or nearly so, additional assumptions must be introduced in order to develop a quantitative phase analysis. It is the purpose of this paper to examine some of these assumptions and to demonstrate their application, particularly to refractory cement systems.

Jan 1, 1982

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Chen L. Lin

Scientific visualization is an ideal methodology for investigating complex phenomena that are characterized by large amounts of data. Furthermore, it is invaluable in the study of processes that evolve in time. Scientific visualization relies heavily on computer graphics, image processing and video technologies. Specific applications of scientific visualization in the minerals and materials processing fields that are considered in this paper include: 1) applied CT technology for multiphase materials and minerals, 2) time averaged density profla in air- sparged hydrocyclone (ASH) flotation and 3) dynamic motion analysis of ball mill grinding.

Jan 1, 1993

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By Duan Xin-hui, Wang Xin, Peng Jin-hui, C. Srinivasakannan, Zhang Li-bo

The work attempts to optimize the process of preparation of modified semi-coke from semi-coke using phosphoric acid (H3P04) as the activating agent using the response surface methodology (RSM). The influences of three major dependent variables, the impregnation ratio, activation time, and activation temperature were assessed on the independent variables yield and the iodine number. The empirical relationship between the dependent and the independent variables were established using the quadratic response surface models, which were utilized to optimize the process parameters. The significance of each of the parameters and interaction among the parameters on the independent variable was assessed based on analysis of variance (ANOVA). The process variables were varied within the range of impregnation ratio (IR) from 1.5 to 4, activation time from 30 to 90 min and activation temperature from 550 'C to 650 'C. The optimized process conditions were estimated to be an IR of 2.29, activation time of 32 min, and an activation temperature of 605°C respectively using the process optimization tool. The BET surface area of modified semi-coke of the optimized sample was estimated to be 915m2/g, with the pore volume of0.71cm3/g, with an average pore diameter of 3.09 nm, with micropore volume fraction being 52.36%. The scanning electron microscope (SEM) images were utilized to visualize the surface pore structure.

Jan 1, 2013

By Charles W. Kenney

Mercury contamination of soil at an old chemical plant surrounded by a residential community and adjacent to a river has provided unique challenges for the current owner. Inorganic and organic mercury compounds had accumulated over the past 50 years to levels that require remediation. Hazen Research, Inc. conducted a multi-phased program to characterize contaminants and their occurrences, evaluate various treatment technologies, and demonstrate the selected technology at bench and pilot scales. A combined physical cleaning and chemical treatment was demonstrated to meet treatment goals for the site. This paper discusses the methods of process selection and results of the bench-and pilot-scale testing.

Jan 1, 2003

By K. Fagerlund

Methods for simulation of settler reactions, matte-slag separation and matte settling in copper flash smelting have been examined. The reaction, separation and settling phenomena of slightly oxidized chalcopyrite samples and cuprous sulfide-magnetite mixtures in fayalite type slags were examined at about 1300°C under inert atmosphere. Two methods based on introduction of molten samples of oxidized chalcopyrite concentrates or synthetic matte-magnetite mixtures onto the surface of molten iron silicate slag were tested. In the first method the samples were water quenched and polished specimens were studied and analysed using light optical microscope, scanning electron microscope, energy dispersive spectrometer. In the second method processes taking place after the introduction of samples onto the slag are followed "in situ" using X-ray transmission image monitoring. Great differences were observed in separation and settling behaviour of low and high grade copper mattes produced as a results of interaction of initial samples and slag.

Jan 1, 1997

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995