Search Documents

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By Masaki Imamura

A novel hydrometallurgical process for copper concentrate treatment has been developed by Niihama Research Laboratories of Sumitomo Metal Mining Co., Ltd. The process has numerous advantages with respect to the operational and environmental aspects. For example, copper is leached effectively from chalcopyrite concentrates by chlorine gas under atmospheric pressure. The copper in the leach solution is then separated from iron and silver by solvent extraction and undergoes electrowinning for its recovery as a highly pure copper metal; this does not require any further purification. Moreover, iron metal can be produced from the purified raffinate by electrowinning without generating a large volume of goethite or hematite, which are solid wastes generated due to iron rejection in common hydrometallurgical processes. This process can also realize the efficient recovery of precious metals. The results of batch testing and continuous-operation testing are presented in this paper.

Jan 1, 2006

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By Abhishek Lahiri, Animesh Jha

"A new technique for the selective separation of rare earths and impurities from lower grade titaniferous ores has been developed which will reduce the overall reduction in the energy costs, and therefore the CO2 generation by at least an order of magnitude during the chlorination and waste handling stages of TiO2 to TiCl4 reaction. The process includes roasting the ilmenite ore with alkali followed by water washing step, which removes nearly 80% of oxides of lanthanide and actinide elements present in lower grades of titaniferous minerals. In the context of preferential separation of rare- 3+ + earth and actinide oxides, we have examined the roles of Al and K ions on the lattice structures of ilmenite and complex titanate as the product layer forms during the roasting in air in the presence of potash. The composition of the mixtures of oxides derived from the separation process shows that the mixture of rare-earth oxides m ay be a high-value co-product of the overall beneficiation process.IntroductionWorldwide the production of synthetic rutile is carried out either by the sulphate or the slag-making followed by fluidised bed chlorination of TiO2 enriched slag granules. The chlorinated gas is then re-oxidized to make white pigment grade TiO2. The waste generated by the sulphate process is predominantly iron sulphate, which has limited use in the water treatment plant. The remaining wastes from the sulphate process undergo further treatment using filtration followed by evaporation and thermal decomposition after which it is disposed into deep sea. On the other hand the chloride waste is extremely hazardous and requires special case by neutralisation, followed by impoundment in a managed pond, where it is monitored for long-term for potential contamination to the soil and ground water. Rare-earth and prelanthanide wastes often end up in the pond where they are diluted and irretrievably lost for further use or recycle. Certain parts of the world the chloride process wastes are pumped via deep boreholes into porous geological strata. The present techniques of disposal are not only expensive but also pose continued threat groundwater and soil and marine life in case of sulphate waste [1, 2]."

Jan 1, 2009

By Qin Hua, Xiangru Chen, Qijie Zhai, Yongsheng Yan, Liang Chang

"In this paper, pure bainite ductile iron and their alloying form of 0.2wt% niobium were prepared by a controlled cooling heat-treatment. The effect of niobium alloying on the microstructure, hardness and impact toughness of bainite ductile iron was studied. The results show that adding niobium effectively improves the hardness and toughness of bainite ductile iron. The hardness and the impact toughness of niobium-alloyed bainite ductile iron were investigated by varying the temperature at which samples were fed to the incubator.IntroductionThere are two essential methods to prepare the bainite ductile iron: isothermal quenching [I-31, and alloying [4• 51• Isothermal quenching process is very time and energy consumable, concerned as a high cost technique for mass production. Besides, there are certain limitations on the size and shape of castings in this process. In addition, it potentially harms the environment. As for the alloying, Ni, Mo, and Cu have to be utilized to obtain bainite. However, the large demand and high cost of Ni makes it not feasible in practice.It is well known that niobium can promote the formation of carbon compound, and improves the stability ofundercooled austenite, which is preferred to the increase of the hardenability. Previous studies showed that niobium could refine the grain and improve the mechanical properties of gray cast iron [6-81 • Therefore, in the present work, the effects of niobium and the temperature at which samples were fed to the incubator on the microstructures and properties of niobium alloyed bainite ductile iron were investigated."

Jan 1, 2014

By Kunio Nakahara, Kashiwagim Junichi, Takao Hayashi

"There are many problems for electronic devices and parts which were caused electrostatic damage by static electricity. It is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating. Mitsui Mining & Smelting Co., Ltd. developed metal oxide type electroconductive pigment PASSTRAN (trade mark) Type-IV which is barium sulfate coated with SnOz(Sb) thin electroconductive layer. This paper shows about pigment characteristics and film condition of antistatic transparency paint which contained PASS TRAN.L.IntroductionRecently rapid development of electronics technology diffused electronic devices and products to Office, Factory, Laboratory and our life. But the other side, there are many problems for electronics parts which were caused electrostatic damage under static electricity. Demand of antistatic materials were become lager by this situation.There is close relationship between surface resistivity of material and static electricity. If the surface resistivity of object is enough low (under 109 Q /Sq), static electricity is dissipated quickly. So it is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating.1) There are many type of electroconductive materials, for example, carbon black, metal powder, electroconductive polymer and so on. Especially, carbon black is used for general purpose by reason of its low cost, but it has big problem of black color. It can not get any color without black, and it caused contamination of carbon.In recent years, metal oxide electroconductive pigment (ECP) was developed and used for special purpose which demands transparent coating or easy dispersion to make ECP paint or endurance under hard environment and so on. Mitsui Mining & Smelting Co., Ltd. developed electroconductive pigment PASSTRAN Type-IV which is BaS04 coated with electro-conductive Tin oxide layer."

Jan 1, 1998

By E. A. Werner, W. Liebfahrt, J. Blaha

"The influence of the composition and the microstructure on the plane strain fracture toughness of five cold work tool steels all processed via the powder metallurgical route is investigated using 3-point bending specimens. The steels differ in composition and therefore possess different volume fractions of carbides. The amount, size and distribution of the carbides in the matrix are estimated by quantitative image analysis on a plane parallel to the fracture surface without discrimination of the carbide type, since the carbides are always much harder [1,2] than the matrix, irrespective of their composition. Due to the production of the steels via the powder metallurgical route almost all carbides are spherical in shape. The mechanical in-situ properties of the matrix are characterized by indentation tests performed with an ""UltraMicro"" -indenter in a scanning electron microscope.IntroductionCold work tool steels are used as tools in applications where excellent wear resistance and high hardness are required. Examples are cutting, woodworking, thread rolling, wire and deep drawing, cold extrusion and pressing of parts at process temperatures below 200°C. For such applications the steels must show an optimum combination of hardness, wear resistance and toughness while offering good machinability. Hardness and wear resistance are controlled by the amount of carbon and carbide forming elements such as molybdenum, tungsten, vanadium, chromium and niobium. These elements are present in the MC-, M6C and M7C3-carbides and are also responsible for the precepitation of secondary carbides during tempering. In this report attention is paid to the influence of the primary carbides only, while the very small ~~nm) secondary carbides will be treated as constituent of the homogeneous matrix. Increasing the amount of carbides (alloying elements) usually results in a decrease of the material's toughness which is caused by the presence of clusters and/or bands of carbides. To achieve an optimum combination of hardness, wear resistance and toughness many of the today's cold work tool steels are processed via the powder metallurgical (PM) route, which helps to prevent non-uniform element/carbide distribution because of the rapid solidification of the powders used. The resulting microstructure of the tool steel then consists of a tough matrix with uniformly distributed hard carbides· of globular shape. This shape of the carbides is also desirable instead of blocky carbides present in non-PM tool steels, since they improve the machinability of the steel. An additional advantage of PM-steels lies in the possibility to produce near net shaped tools thus lowering the costs of machining."

Jan 1, 2000

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By James E. Hoffmann

This paper briefly reviews the conventional technologies employed for the treatment of copper refinery electrolyte bleed. The strength and weaknesses of conventional practice will be reviewed and a number of process options to address the weaknesses of present process technology will be described and evaluated. The effect of process selection upon energy consumption and the environmental aspects of process effluent control will be discussed.

Jan 1, 1997

By M. Hochenhofer

Due to economic aspects and environmental regulations recycling of slag and waste from ferroalloy production became a very important issue for the companies during the last years. The treatment of slag depends prior on the composition, especially on their content of valuable metals and impurities. The final aim should be a total re-use of these materials in the industry e.g. cement industry, pig-iron production etc.. Therefore, to reach the required physical and chemical properties for a further use, possibilities of a metallurgical treatment have been investigated. The conditioning of slag with a high V-, Mo- and P-content via reducing metal bath showed to be one alternative. To determine the optimal process parameters, practical investigations with different slag compositions and thermodynamic calculations were carried out.

Jan 1, 2006

By Jean-Christophe Gebelin, Mark Jolly, Samantha Jones

"The de-waxing process in investment casting is truly a black art which is carried out in a black hole - the autoclave. The process involves exposing wax, coated by a porous ceramic shell, to steam at a pressure of 10 bar and a temperature of about 180°C. The processes which then occur are truly multi-media and multi-physics. Steam condenses in the porous ceramic, wax melts and flows, the shells expand and sometimes crack. Why the shells crack is one of the most difficult questions asked in the industry.Modelling and validating the de-waxing process is not simple. The IRC at the University of Birmingham is attempting to model this process using Physica+ a code developed in the UK. This paper will present the latest results in this attempt to model one of the casting industries most intractable problems.IntroductionThe de-waxing process using an autoclave involves the following physical phenomena:· Flow of the steam in the autoclave;· Heat transfer from the steam to the wax, possibly through the shell;· Melting and flow of the wax.At the same time, other phenomena may occur, such as the flow of the steam through the shell, the condensation of the steam on the shell surface and on the wax pattern surface, the flow of wax the through the shell, etc ...This shows how complex the de-waxing process is from a physical point of view. The main defect that appears during this process is the cracking of the shell. Previous modelling work carried out by Snow [1] has shown that it is possible to predict the stress in the shell, making numerous assumptions. In this paper, the modelling to predict the state of stress in the shell that is currently in development at the University of Birmingham is presented together with the presentation ofthe physical phenomena to model and the assumptions used. The parameters that are needed in such models will also be discussed, and some experimental work undertaken at the moment presented."

Jan 1, 2001

By T. Sakaguehi

Some attempts were made to recover and remove of uranium that may be present in refining effluents, mine waste Water, and other waste sources by using microbial biomass. To establish which microorganisms accumulate the most uranium, 135 species of microorganisms (42 bacteria, 26 yeasts, 34 fungi and 33 actinomycetes) were screened. Of these 135 species of microorganisms tested, extremely high uranium absorbing ability was found in Pseudomonas stuzeri, Neurospora sitophila, Streptomyces albus and Streptomvces viridochromogenes. In addition to the research on uranium uptake, thorium recovery by using microorganisms was investigated. High abilities were found in Streptomyces levoris and Bacillus subtilis. The selective accumulation of heavy metal ions by various microorganisms has also been examined. Uranyl, mercury and lead ions were readily accumulated by almost all of the species of microorganisms tested. Actinomycetes and fungi differ from many bacteria and most yeasts in their selective accumulation of uranium, and mercury. The basic features of uranium uptake by Streptomyces viridochromogenes, a microorganisms with high uranium-uptake ability, were investigated systematically. Synthesizing these results, we suggested that the accumulation of uranium into these microbial cells is not directly mediated by any metabolic process:, but almost completely dependent upon physicochemical adsorption on the cell components. In addition to this fundamental research, uranium recovery was investigated in immobilized Streptomyces viridochromogenes. These immobilized cells adsorbed, uranium readily and selectively. The immobilized cells recovered uranium almost quantitatively and almost all uranium adsorbed was desorbed with 0.1 N Na2CO3, These results showed that microbial cells are more stable after Immobilization and can be used repeatedly for the process of uranium adsorption-desorption. These results suggested that these microbial cells can be used for the recovery and removal of nuclear fuel elements, such as uranium and thorium, from refining effluents and mine waste water.

Jan 1, 1991

By Pratheesh George

Solid state galvanic cell with CaF2 as the electrolyte was employed for determining the thermodynamic properties of Nb-Al binary alloys in the temperature range of 973-1073 K. The activities and activity coefficients of Al in NbAl3 were determined. The experimental procedure and the design and construction of the experimental setup have been also explained in detail. Aluminum activity in NbAl3 increased with increase in temperature and shows a strong negative deviation from ideality. The activities of aluminum in NbAl3 were determined to be 0.0165 and 0.0289 at 973 and 1073 K respectively. The stability of NbAl3 has been compared with other available intermetallic systems.

Jan 1, 2006

By XING Xiangdong, Zhang Jianliang, MA Jinfang, WANG Zhenyang

The non-equilibrium reflux reaction behavior of phosphorus was studied with synthetic slags formed by using the AR chemical reagents and changing the initial condition of basicity, FeO, MgO and Al2O3. Due to increase of viscosity, the dephosphorization slag with high basicity inhibits the full contact of slag with iron, which leads to the low reaction rate in the early stage. However, since the high basicity improves the activity coefficient of CaO, the dephosphorization rate and phosphorus capacity goes up in late reaction stage. FeO promotes the increase of reaction rate in early dephosphorization stage. But the polarization force of Fe2+ is stronger than Ca2+, which hinders the reaction between phosphate ion and CaO and reduces the stability of PO4 3-. Thus, high content of FeO will adversely impact on dephosphorization reaction. In addition, MgO has a promoting effect to the dephosphorization, whereas Al2O3 has a negative influence.

Jan 1, 2016

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006