Search Documents

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By B. Erik Ydstie, Tor Lindstad, Vianey Garcia-Osorio

"As a result of the high temperatures present in a Carbothermic Aluminum Process the content of aluminum and aluminum sub-oxide in the gases leaving this process is high. These gases as well as energy must be recovered. In a Vapor Recovery Unit were the aluminum compounds react in a series of Heterogeneous Non-catalytic Reactions forming solid, liquid and gas products. The different product phases depend on the temperature present in the system. In this work we present dynamic model of the Vapor Recovery Unit of a conceptual Carbothermic Aluminum Process. Because of the complexity of the system several models are developed and coupled to capture the essential physics of the multiphase reaction problem. A Shrinking Core Model describes the reaction mechanisms. Then material and energy balances are coupled with the thermodynamics properties from the FACT database of thermodynamic properties, resulting in a system of nonlinear Partial Differential Equations. In the paper we describe the model development and governing equations for the reaction mechanisms and fluid flow. Finally we review the numerical schemes created for the solution of the model system. The model can be used for control and design purposes.IntroductionThe Carbothennic Processes for producing Aluminum can be divided into two groups (Motzfeldt et al. (1989)) In the first approach pure alumina is produced and reduced to pure aluminum. In the second approach an alloy (e.g. aluminum and silicon) is made and then aluminum is produced from the alloy. The history of both processes has been described by Ginsberg et al. (1965). At least three aluminum producers began largescale testing of this process in the 60's Alcan, Pechey-Ugine and Reynolds. Alcoa did some smaller scale experiments.Alcoa was one of the first companies to produce aluminum by Carbothennic Reduction (Foster et al. (1956)) and US Patent 2,829,961 April 8, 1958. In this process a carbon containing molten aluminum phase was a floated on top of an oxy-carbide melt. During the cooling the dissolved carbon deposited as aluminum carbide. The carbide was then separated from the molten aluminum by a fluxing agent. This process was successful but economic unfeasible."

Jan 1, 2001

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By Petr Dvorak, Jana Selucka, Hong Vu, Petra Starkova, Tomas Frydl

Waste, generated during high pressure leaching of lateritic nickel ores, contains about 50% of iron in form of magnetite but high chromium content ( *3%) does not allow its extensive utilization as the raw material for pig iron production in blast furnace. The chromium removal from the waste was carried out by two methods: (1) oxidative alkali roasting with NaOH and/or Na2CO3, followed by water leaching and (2) oxidative leaching in KOH sub-molten salts solutions. The results show that about 90.1% of Cr was removed when the waste was roasted at 900 °C for 3 h with 33.1 wt% of NaOH. The removal of 88.2% of Cr was achieved if the waste was roasted at 900 °C for 3 h with 40 wt% of Na2CO3. The sodium content in the water-leached residues was reduced from 5% to about 0.5% by reaction with CaO in aqueous solutions at 80 °C for 2 h. About 70% of Cr was removed if the waste was leached at 190 °C in 73 wt% KOH for 8 h.

Mar 1, 2017

By Shunhong Huang

Thirty-five soils were sampled from three sites at different distances from chromium slag heap of a Iron-alloy factory, namely, nine from site A located under the chromium slag and eighteen from Site B in the vicinity of the factory and eight from site C far from the factory. The contents of total Cr in these soils from site A, B and C were 1666.0±1310.9 mg? kg - 1,1136.2±1844.6 mg? kg - 1 ,300.4 ±165.1 mg? kg ? 1, respectively. The contents of water soluble Cr were 59.3±77.57 mg? kg ? 1,0.6 ±0.3 mg? kg - 1 ,0.5±0.3 mg? kg - 1 , respectively. In order to evaluate soil health, the activities of four soil enzymes (catalase, polyphenol oxidase, dehydrogenase, alkaline phosphatases) were analyzed. The results have shown that dehydrogenase activity was greatly depressed by conditions in the heavy chromium-contaminated sites. Negative correlation was observed between dehydrogenase activity and the distance from the chromium slag heap, however, the activities of catalase, polyphenol oxidase, alkaline phosphatases in soils from the three sampling sites mentioned above did not differ significantly. The result imply that of dehydrogenase activity could be used as an indicator for the chromium pollution level in the area of Iron-Alloy factory and for the stability level of the soil ecosystem.

Jan 1, 2008

By B. Mishra

The application of various bydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, eg. metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been 'investigated and suggested for dealing with some of these wastes' and scrap material. The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained? from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EMI' and decontamination and decommissioning [D&D].

Jan 1, 1996

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By S. N. Monteiro, E. B. Zanelato, J. Alexandre, M. T. Marvila, A. R. G. Azevedo, G. C. Xavier

One of the parameters used in the study of mortars is the adhesion resistance, which indicate show much the mortar adhered to the substrate. The usual study is done at 28 days, to worldwide standardization. Few researchers study the adhesion of mortars to ages other than 28 days. In this scenario, the adhesion strength tests of conventional mortar with a 1:1:6 mass scale (cement, and sand) at 7, 14, 28, 56, 91, 182 and 364 days were performed in order to understand the behavior of this material. The usual characterization tests of the mortars were carried out to correlate the values obtained with the adhesion results. The obtained results demonstrate that the mortar continues to gain resistance with the passage of time. For the trait studied the gain was considerable, indicating that over time the cement continues to hydrate, reacting and contributing to the strength of the material.

Mar 1, 2018

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By C. Lupi

In 1996 the Italian Agency for Environmental Protection (ANPA) has initiated a study of the environmental impact of the industrial sector of steel produced by Electric Arc Furnace (EAF). Within the framework of this study a hydrometallurgical process to treat EAF dusts was considered and developed. The paper describes the zinc and lead recovery from fumes coming from carbon steel production. The zinc extraction consists in acidic leaching followed by SX-EW steps. The leaching sludge containing lead sulfates was treated to obtain pure lead salt and inert solid residue. The whole process, that minimizes effluents by recycling the main liquid streams, has been developed to obtain marketable products. The solid waste, containing spinels, was subjected to elution tests in order to verify its compatibility with environmental regulation. The process, that has been set-up and tested in the laboratories of the University of Rome, will be transferred and studied on a pilot plant in order to assess its industrial and economical feasibility.

Jan 1, 1999

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By B. Mishra, W. A. Averill

"The application of various hydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, ego metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been investigated and suggested for dealing with some of these wastes and scrap material.The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EM] and decontamination and decommissioning [D&D].IntroductionThe high temperature carbothermic or metallothermic smelting reduction methods for metal production are associated with the generation of significant quantity of waste as slags, flue dusts, sludges, residues, effluent salts etc. Certain hydrometallurgical processes also generate lots of aqueous waste due to the inherent nature of the technique. Also, the gas-based reduction processes are not applicable to many stable metal compounds, such as alumina, titania, beryllia, lanthanide and actinide oxides, etc. due to thermodynamic considerations. All these methods cause substantial environmental hazard. There is a need to develop alternative processes which have low waste or ideally a ""zero-waste"" generation.Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore (aluminum, beryllium, neodymium, plutonium, uranium, etc.) or from other process effluent that contain reactive metal compounds. The processes reduce metal compounds electrolytically (A12O 3 and BeCI2) on a carbon anode or by calciothermic reduction (Po, Nd). The by-product, in the latter case, is a calcium oxide saturated halide salt. The waste-treatment to recycle the halide has to be done as a separate step or stored as a contaminated waste. A successful separation technology can provide a new insight to the waste minimization strategy for the nuclear industry."

Jan 1, 1996

By Yan Zeng

Lithium metal silicates (Li2MSiO4, M = Fe or Mn) composed of abundant and non-toxic elements are important cathode materials for Li-ion batteries (LIB). In contrast to solid-state or sol-gel methods, hydrothermal synthesis conducted in pressure reactors is a favorable processing route as it provides the potential for scalable production and is environmentally benign. However, the key is to control the precipitation reaction to obtain powders with desired properties to meet battery specifications. Through a systematic study, we have found that Li2MSiO4 with tunable size from 300 nm to 1.5 μm can be produced by adjusting precursor concentrations, temperature, and reaction time. Under optimum conditions, high purity Li2MSiO4 with minimum defects were successfully produced and examined as an LIB cathode. The use of complexing agents promoted the formation of unique hollow particles via the self-assembling of elongated crystals. A four-step formation mechanism is proposed based on extensive characterizations with XRD, HR-TEM, SEM, and Mössbauer spectroscopy.

By Yeole Shivraj Narayan, Nunna Nagabhushana Ramesh, Banoth Balu Naik, Alluru Ramya

MicroEDM process is mainly used for producing miniaturized features like microholes on different types of materials that are hard to cut and difficult to machine. One typical application of microEDM process is microhole drilling operation. Choice and utilization of optimum pulse parameters is of utmost importance for achieving superior surface quality and higher machining rates. However, the process is characterized by low machining rates and considerable overcut as compared to conventional EDM drilling. An attempt is made to investigate the effect of pulse parameters on maraging steel 300 alloy during micro EDM drilling. Parameters like pulse on time, pulse off time, voltage and current are explored through 09 experiments replicated thrice using Taguchi method. Machining characteristics like material removal rate and overcut are studied while drilling micro holes of 500 µm diameter using brass electrode. Evaluation of microhardness after microdrilling is also performed. It is found that puls on time and current influenced the machining characteristics. Minimal change is observed int he microhardness of the alloy after microdrilling.

Mar 1, 2018