Search Documents

By Yuzo Hiroshige, Masayuki Kyoi, Tomonori Saeki, Masahide Okamoto, Toru H. Okabe, Yu Miyamoto, Tomohiko Akahori, Takeshi Nemoto

We report Hitachi's approach to establish the recycling process for rare-earth metals in magnet. We have developed a process to disassemble the used electric products to collect the magnets, a process to remove the surface plating film of the magnet, and processes to separate rare-earth metals from the magnet. All processes are operated without chemical solutions in order to minimize the environmental impact due to the waste water emission. For the disassemble process, we have developed an equipment to generate continuous shock on the electric products to loosen screws. A sand blast technique is applied for the plating removal process. Rare earth metals in the magnets are extracted by immersion of the magnets in molten magnesium. The extracted rare-earth metals are separated from Mg by evaporation of Mg. The overall yield of recovery is 86.8 %. The purity of the final rare-earth metal is 98.8 %.

Jan 1, 2014

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By R. I. Rodriguez

Since the 1973 energy crisis, high fuel oil costs have been eroding the economics of the Nicaro and Punta Gorda Plants that employ the Caron Process for laterites processing. Since 1995, Cuban crude oil production has growth dramatically, with progressive utilization in power generation, cement and nickel plants. This paper shows how Nicaro and Punta Gorda plants have been able to shift from expensive Bunker C Fuel Oil to heavy but cheaper Cuban Crude Oil of high Sulfur content and achieve a significant reduction in operating cost. Problems related to the high sulfur content of the Cuban crude oil have demanded extensive investigations of the process chemistry and novelty solutions are proposed, with corresponding changes in process conditions. Innovative options are shown that will allow further cost reductions in the future. Keywords: Cuban Crude Oil, Sulfur, Ammonia.

Jan 1, 2004

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By F. R. A. Jorgenson

The ignition of chalcopyrite and pyrite was studied using laminar flow furnace and thermal analysis techniques which were supported by XRD and optical microscopic examination of the products. In air, chalcopyrite and pyrite ignited at temperatures of 400-500'C and 500-600?C respectively. The phase assemblages predicted from thermodynamic analyses were compared with those found by experiment, and the onset of ignition was correlated against changes in the phase compositions. Pyrite and chalcopyrite ignited when pyrrhotite and intermediate solid solution formed thus opening up the structure and allowing ready access of oxygen.

Jan 1, 1989

By Hans Korfmacher

Product take-back regulations implemented in Europe have presented significant challenges to the consumer electronic product and battery industries. Initially companies established single compliance organizations within individual Member States. These programs met business needs but were inefficient and costly. They were protected from pressures of marketplace competition and could not leverage economies of scale. In order to address these problems P&G, Hewlett Packard, Sony and Electrolux conceived a pan-European compliance organization to collect waste electronic equipment Europe-wide. This organization, called the European Recycling Platform (ERP), operates in competition with existing national compliance systems. Since 2005 ERP has collected 800,000+ tons of waste electronic products and delivered millions of dollars in cost savings. This presentation reviews the steps needed to establish successful competitive collection organizations that provide sustainable recycling at the lowest cost.

Jan 1, 2010

By E. V. Redin, B. A. Dubrovsky, E. V. Knyazev, A. I. Starikov

"Ti-V magnetite is one of the most abundant composite ore resources in the world. This ore cannot be fully processed via blast furnace technology because of high content of Ti02. According to the investigations carried out in the USA and Japan ITmk3 RHF (Rotary Hearth Furnace) technology is a breakthrough in Ironmaking. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from Ti-V magnetite ore via the ITmk3 by means of the lab scale testing. Samples of ore from the Maly Kuybas deposit (Southern Ural), carbon reductant and fluxes were chemically analyzed. Green pellets were processed via a lab chamber furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities [l]. After pilot testing at Kobe Steel's Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics put into operation the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota) in 2010. Results were consistent with nugget characteristics confirming ITmk3' s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from the Ti-V magnetite bearing ore with high content of Ti02 and Alz03 has been done. It is well known, if a lot of Ti02 and Alz03 enter the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace. Besides, high content of Alz03 raises the melting temperature of gangue minerals disturbing the coalescence of reduced iron to the nuggets."

Jan 1, 2013

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By A. V. Tarasov

The proposed process is based on creating a controlled frothed layer of molten slag, in which fine particles of carbonaceous reductant and raw material to be processed are mixed with emulsified iron. Frothing of the slag layer without external blowing occurs as a result of intensive evolution of gaseous reduction products. The froth reaction process is maintained due to the heat of an electric arc in the slag layer. When the metal bath is heated by the arc to 1400- 1 500°C, the low temperature of the slag surface of about 1200-1 300°C is maintained due to low thermal conductivity of slag froth preventing heat loss. In order to maintain the required slag froth level and control the process temperature, air tuyeres are installed above the slag bath; blowing air serves also for oxidation of zinc in fumes and for its transportation. High adsorption and thermal insulating properties of slag froth ensure virtually complete elimination of dust and mist entrainment along with low heat losses. The main macrokinetic regularities of the carbon thermal reduction of zinc-containing slag melts have been studied under frothing conditions. The mechanism of formation of gas-slag emulsion has been identified under the conditions of reaction [C]+[O]=CO occurring locally at the slag-metal interface. It has been demonstrated that under the froth reduction conditions the zinc removal rate from the melt increases on the average by 3 to 5 times. Based on the physical and chemical data obtained, basic principles of the dezincing technology have been developed for different intermediate oxide iron-containing products produced in the process of ferrous and non-ferrous metals production.

Jan 1, 2002

By Anjali Talekar

Low temperature heat capacities of pentaerythritol [PE: C(CH2OH)4], pentaglycerine [PG: (CH3)C(CH2OH)3], and 2-amino-2-methyl-1,3-propanediol [AMPL: (NH2)(CH3)C(CH2OH)2]have been determined by adiabatic calorimetry from 3 K to 300 K. To the best of our knowledge, this is the first reported heat capacity measurement below 280 K for PE and AMPL. The Debye temperatures for these organic crystals have also been determined and compared with other alcohol derivatives of neopentane.

Jan 1, 2006

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Richard D. Hagni

The techniques of reflected light microscopy and cathodoluminescence microscopy are uniquely suited to the study of the products from many important industrial problems. Ref1 ected 1 ight microscopy provides the means to rapidly identify the mineralogy of an industrial sample, determine the abundance of each phase, and examine the mineral intergrowths or textures. Cathodoluminescence microscopy is a relatively new instrument that provides the means to cause many minerals to cathodoluminescence under the microscopy. The cathodoluminescence of a mineral allows it to be readily distinguished from other phases that differ in cathodoluminescence but are similar in optical properties. Cathodoluminescence microscopy is especially useful to detect cathodoluminescence minerals that are present in only small quantities. Reflected 1ight microscopy and cathodoluminescence microscopy have been successfully applied in studies of beneficiation products, prediction of beneficiation and leaching problems, phosphatic iron ores and mill products, pyrometallurgical products, roasted refractory gold-bearing sulfides, ceramic build-ups, electric arc furnace and smelter dusts, and other industrial products.

Jan 1, 1993

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By Saynbaatar, Gangping Ma, Jianhua Fu, Qiqige, Jinghua Wang

The influence on the performance of foam concrete made by replacing cement with some industrial waste residues was researched in this paper. The result shows that the 7d and 28d compressive strength of foam concrete increases firstly and then decreases with the increasing amount of industrial waste residue. The proper added range is 10%-20% for steel slag, blast furnace slag and coal ash, but, 8% for desulfurized fly ash. With the proper adding ratio, the compressive strength of foam concrete always increased comparing with the pure cement foam concrete. When adding 48% of the compound industrial waste residues, the 28d compressive strength of the foam concrete reached the 2.9MPa which could match the pure cement foam concrete. The results indicates that there is a synergistic effect among the compound industrial waste residue, and this effect is benefit to improving the compressive strength of foam concrete.

Jan 1, 2015

By Wangzhi Zhou, Huasheng Chen, Bowen Li, Meng Liu, Mingsheng He, Long Zou

Steel slag is an inevitable by-product from a steelmaking furnace such as a converter, an open-hearth furnace or an electric arc furnace. The yield of steel slag increases with the sharp rise of steel production. Utilizing the slag effectively and comprehensively is one of the important tasks to promote the development of iron and steel industry in China in a sustainable and efficient way. In this study, hot-poured steel slag from a converter was used to prepare ceramics by mixing with fly ash, microsilica, and quartz. After heating at 1100–1200 °C, the ceramics were well sintered. XRD revealed that multiple crystalline phases coexisted in the glass-ceramics, and the main crystalline phases were diopside and anorthite. SEM observation indicated that there was a plate-columnar composite structure in the ceramics. Reaction mechanisms were discussed.

Mar 1, 2018

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014