Search Documents

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the effect of inoculums volume on bioleaching to recover metals from printed circuit boards using Acidithiobacillus ferrooxidans-LR. Printed circuit boards from obsolete computers were mechanically processed by comminution followed by magnetic separation, and the obtained non-magnetic fraction was used in the bioleaching experiments. A shake-flask study was carried out on the non-magnetic fraction samples using a rotary shaker at 30°C, 170 rpm and different volumes of oxidized culture solution as inoculums (%v/v): 5, 10, 20, 30, 40, 50 e 60. The oxidized culture solution was prepared inoculating pre-adapted bacteria Acidithiobacillus ferrooxidans-LR (5%v/v) in 200mL T&K medium. Leaching in acidic ferric sulphate was also performerd. The analyzed parameters were pH, ferrous iron concentration and metals analysis (AAS). The results showed that using 10%v/v of inoculums were extracted 99,2% of copper and 60% of aluminum by bioleaching. Zinc, lead and tin extraction were not influenced by bacterial leaching and extractions rate were obtained by chemical leaching promoted by acid medium. Ferric iron leaching extracted less copper (35%) than bioleaching. SEM analysis shown surface difference between samples of non-magnetic fraction before treatment and after bioleaching, showing corrosion pits formed by the bacteria contact.IntroductionWaste of electrical and electronic equipments (WEEE) has been target of discussion due to environmental, political and economical issues involved. Around 17 million of computers are discarded annually in the world due to malfunctioning equipment or because technologies become obsolete [1,2]. In contrast, only the central processing unit (CPU) of computers weights around 3kg. From this data, it can be calculated that 51 million kilograms of CPU waste are discarded yearly. This calculation was performed considering only the CPUs, disregarding the cathode ray tubes and liquid crystal displays of monitors [3,4]. Because of the amount that has been accumulated, e-waste has become a global problem but also can be an alternative source to recover valuable materials [5,6]."

Jan 1, 2012

By Toshiyuki Nohira, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The electrochemical formation of Tb-Ni alloys was investigated in a molten LiCl–KCl–TbCl3 (0.50 mol% added) at 723 K. Open-circuit potentiometry was conducted using a Ni electrode after electrodepositing Tb metal at 0.20 V (vs. Li+/Li) for 300 s. There were four potential plateaus at (a) 0.66 V, (b) 0.80 V, (c) 0.95 V and (d) 1.56 V, respectively. Alloy samples were prepared by potentiostatic electrolysis at 0.60 and 0.70 V at 723 K. The alloy phase was identified as only TbNi2. Anodic dissolution of Tb from the formed TbNi2 was conducted at 0.90, 1.20 and 1.60 V, respectively. In the sample obtained at 0.90 V for 3 h, the existence of TbNi3 was identified by the XRD. Phase of the sample obtained at 1.20 V for 3 h was TbNi5. The sample obtained at 1.60 V for 3 h was Ni. Alloy samples were prepared by potentiostatic electrolysis at 0.50–0.80 V for 1 h using Ni plate cathodes in a molten LiCl–KCl containing TbCl3 (0.50 mol%) and NdCl3 (0.50 mol%). The highest mass ratio of Tb/Nd in the alloy sample was 56 at 0.70 V.

Mar 1, 2018

By Tracy Morris, Weldon Read, Luis Navarro

"During the leaching of anodic slimes, tellurium dissolves into the leach liquor together with copper and must be removed before the solution is sent to liberator cells for copper recovery. Prior to the installation of autoclaves, tellurium was precipitated using raw slimes that caused a recirculation of tellurium in the leaching circuit. After autoclaves were installed the old leach tanks were converted into tellurium reactors utilizing copper chips, steam and agitation to form a copper telluride precipitate. Tellurium levels of less than 10 rng/L are achieved in a timely manner.IntroductionThe electrolytic refining of copper consists of an electrolytic cell provided with an anode of impure copper, a cathode of substantially pure copper (starter sheet) and an electrolyte made of copper sulfate and sulfuric acid [1]. When a direct electrical current is passed between the anode and cathode inside the cell, the impure copper anode dissolves in the electrolyte and pure copper is plated onto the cathode. During this operation, many of the impurities are deposited on the bottom of the cell as an anodic slime residue composed of insoluble chemical compounds. Slimes are a major source of rare and precious metals in the copper industry [2-5],In the Amarillo Copper Refinery (ACR), the anodic copper slimes are sent to the Precious Metals department in order to extract and then refine the gold, silver, platinum and palladium from them. The remaining impurities, in the form of a soda slag or copper slag are sent to the Hayden smelter for further processing. Copper telluride is sent to the Selenium/Tellurium department inside the plant for selenium and tellurium recovery. During the leaching process of the anodic slimes, copper, tellurium, and other metal species in the slimes are dissolved into leach liquor that cannot be returned to the tankhouse unless the tellurium concentration is below 10 mg/L."

Jan 1, 2012

By M. A. Kader, M. A. Islam, P. J. Hazell, M. Saadatfar, J. P. Escobedo, A. D. Brown

The dynamic pore collapse mechanisms and energy absorption capacity of closed-cell aluminium foams subjected to low velocity impacts have been investigated. Impact experiments were carried out using an instrumented drop-tower with two impactor geometries: a 50 mm square flat steel impactor to investigate pore collapse mechanisms and a 20 mm diameter hemispherical steel impactortostudy indentation resistance.X-ray computedtomography was utilized to generate views of the deformation field within the impacted specimen. The results show that the strain rate and incident impact energy influence the energy absorption capacities of closed-cell aluminium foams. Furthermore, damage initiation, propagation and cell collapse mechanisms under drop weight impact have been elucidated.

Mar 1, 2017

By S. Ikenobu

This paper describes a method for processing high-silicate zinc concentrates by hydrometallurgical zinc refining. Silica in concentrates reacts to form zinc silicate during roasting. The zinc silicate readily dissolves and slowly precipitates in sulfuric acid solutions during leaching. However, if proper operating parameters are not maintained, the colloidal silica may form an unfilterable gel. That is, according to the investigation results obtained, the silica concentration in the reactor has to be maintained at 5 g/1 or less (preferably 2 g/1 or less) by promoting the precipitation reaction. The proposed method has made it possible to precipitate silica in a form having excellent solid-liquid separation characteristics, without the need for facilities having a high filtration capacity, and to maintain a low silica concentration in the reactor by feeding a composition containing pre-adjusted silica contents.

Jan 1, 2000

By David G. Dixon

A general, unsteady-state model for leaching of one or more solid reactant species from a non- reactive, porous, spherical pellet is derived in dimensionless form for the interpretation of leaching data, and for use in the design of coarse-ore leaching processes. The effects of diffusion rate, chemical reaction rate, variable reaction order, and competition between multiple solid reactants are examined using the concept of the effectiveness factor. It is shown that the model is capable of simulating both "reaction-zone" and "heterogeneous" kinetics, depending on the choice of three dimensionless parameters. Results of batch leaching tests of artificial ore pellets are presented, and their relationship to the model is discussed.

Jan 1, 1993

By Luciano B. Oliveira, Angela O. Costa, Sergio N. Monteiro, Luis Guilherme C. Marques

"Biofuels are gaining a relevant role in today’s world not only as a solution for the decreasing petroleum reserves but mainly as a positive contribution to the efforts in global warming mitigation. In Brazil, since 1975, the replacement of gasoline by ethanol started a so-called PROALCHOOOL program, which is now being complemented with the replacement of petroleum diesel by biodiesel. This biodiesel program was officially created in 2005 with mandatory goals, supported by legislation, of 2% addition in 2008 and 5% addition in 2013 into all commercialized regular diesel. In this work, a critical analysis of the Brazilian biodiesel program is presented. The technical aspects related to the different raw materials, including wastes, available for biodiesel conversion as well as the economical conditions associated with production costs and market logistic are discussed. The environmental benefits associated with the retention of greenhouse gases are also discussed.IntroductionToday the commonly accepted fact that the petroleum world reserves are probably passing through a maximum and start declining in terms of the total amount that can be extracted by existing technologies is motivating significant changes in our society. The continuous increase in the price of gasoline and other liquid fuels is an immediate worrisome and visible consequence. However, more than an economical problem, our civilization is already facing the effects of global warming, due to CO2 emission from burning fossil fuels, mainly from coal and petroleum. It is now realized that a large scale solution for these problems demands the prompt substitution of non-renewable fossil fuels by others that, in addition of being renewable, have a relatively lower contribution to the greenhouse gases."

Jan 1, 2008

By Sergio Demetrio

Based on the current reality of the copper smelters industry, besides the advances that have been and are expected for the next few years, the authors present a futurist vision of the processing of copper concentrates and copper smelters in the years 2000. Outlined new development strategies and ways of improvement in this business, including research, development and management of the works that today posses characteristics of a profitable operation, as well as the changes expected with respect to the entry of new actors and the creation of new products The authors finally bet for small or tailor-made smelters with ad hoc technology for their raw materials and few units to coordinate -devoted to specific concentrates using high technology and low manpower. Considering the in-situ hydrometallurgical route, as well as the pyrometallurgical route in works or conversion facilities that buy or process white metal and produce copper and other metals associated with this such as gold and silver, besides sulfuric acid, plants which should be strategically located in zones with high sulfuric acid price to make this a product which contributes to the profitability of the business.

Jan 1, 1999

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012

By R. G. Reddy

The oxidation kinetics of A13Ti intermetallics have been studied at the temperature range of 850°C to 100O0C in pure dry oxygen. The oxygen diffusion rates were investigated using TGA method. Parabolic rate constants were calculated. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction. A continuous A120, scales with a little TiO2(rutile) were formed on the intermetallic surface. The A13Ti intermetallic exhibited excellent oxidation resistance among the Ti-Al base intermetallics.

Jan 1, 1997

By Klara Kodrikova, Vera Kasparkova, Michaela Uhlirova, Karel Kolomaznik

"Potentially hazardous wastes from leather industry (blue shavings) are processed into various biostimulators within two steps. The first step takes place at high pH (11-12) and hydrolyzation is implemented with potassium alkali, in the second step the pH is lowered to 9 with phosphoric acid after enzymatic dechromation occurs. The resulting hydrolyzates were analyzed in the sense of molecular weight distribution and tested as biostimulators on rape (Brassica napus). The hydrolyzates can be also directly used as universal NPK fertilizers. It has been proved that the nitrate content in the edible parts of tested vegetables (radish, lettuce, and cucumber) was approximately 200 times lower compared to the vegetables fertilized with an inorganic nitrogen fertilizer. The harvests of vegetables fertilized with the hydrolyzate and the inorganic nitrogen fertilizer were almost the same.IntroductionDuring processing raw hide into leather (tanning processes), only 20% of the collagen material is used for the final product. The remaining 80% ends up as waste, both tanned and non-tanned. Non-tanned waste such as calcimine can be used for production of artificial collagen casings for sausages, gelatine and also in pharmaceutical industry as collagen capsulates. Further processing and recycling of tanned leather waste (especially chrome shavings) is more complicated. Although many technologies producing various quality collagen hydrolyzates have been developed and tested in laboratories, few have been implemented on industrial scale. A promising turn came in the works of ERRC USDA [1,2]. They worked out an enzymatic dechromation technology (hydrolysis) and achieved a considerable decrease of the amount of relatively expensive proteolytic enzyme, which solved the difference between the quality and price of the final product. The American experience of enzymic hydrolysis were applied on industrial scale in the Czech Republic, where a plant was built with daily processing capacity of 3 tons of chrome shavings. The experience of real operation was published in [3] and the cooperation between the Czech Republic and USA partners resulted in a patent [4]. The main asset of the patent was the use of volatile organic bases in the hydrolysis process giving high quality and cheap hydrolyzates with low ash content."

Jan 1, 2008

By J. W. Matousek

In the flash smelting of copper sulfide concentrates, the course of reactions from the burner tip, through flame "burn-out" (the point of oxygen depletion), to settled matte and slag is of particular interest in understanding the mechanisms of the process. Numerous reaction sets can be proposed to describe the chemical changes that might be taking place, but from outside the furnace no one set offers an obvious advantage in explaining the actual processes involved. Only a combination of mathematical modeling and flame and bath sampling can achieve this result. This paper shows that flash smelting, while still reasonably orderly, is a more complex process than suggested by the technical literature.

Jan 1, 1993

By Tzu-Chien Lin, Jack Tsai, Ming-Yu Lin, Der-Ray Huang, Jiin-Sen Chen, Jing-Xuan Lin

"In this paper, some DVD-R discs have been selected for long time light exposure test and high temperature and humidity test. Generally, recordable media under long time light exposure maybe be defected seriously. If we use Jitter value 8% as a reference to determine the life time of DVD-R samples, some discs defect after 5 hours of light exposure while some discs can endure over 25 hours. Also if we use reflectivity 45% to determine the life time, some discs defect after 30 hours light exposure while some discs can endure over 40 hours. From our results, the good samples show good characteristics of PI error. The absorption spectrum of recordable media is a good reference to justify the quality of dye media. These results can be used to estimate the life time of recordable discs.IntroductionIn general, the life time of DVD-R with a layer of organic dye recording layer is required for preservation in decades. In addition to optical characteristics and thermal properties, we still need to consider the stability of the dye in recording media. The presentation of the color on organic dye is not only related to the material's property but also related to the light exposure. In this study, we focus on the absorption characteristics and reflectivity of organic dye in optical recording layer after light exposure. The optical properties of discs depend on the functional groups and molecular structure [1]. According to ""DVD Specifications for Recordable Disc (DVD- R)"", the reflectivity should higher than 40%. From measured reflectivity, we can confirm that the important issue is whether dye be affected by light exposure or not. Because each specific functional group absorbs the specific spectrum, we can check the characteristics of functional groups from their UV/Visible Spectra. We also use High-performance liquid chromatography (HPLC) to detect the different components of dye on the recording layer [2]. The jitter value test is to test the error cause by digital signal of recording media. If we use jitter value 8% as a reference to determine the life time of DVD-R samples, the purpose of this study is to investigate the jitter values of recording media after high light exposure and high temperature/humidity test. The results of these test will be helpful for the development of long-life optical storage media."

Jan 1, 2012

By Luis G. S. Sobral, Gabrielle N. Bard

Copper sulphides Concentrates, from the flotation process of copper primary ore; contain, commonly, small amounts of precious metals, such as gold and silver. During the smelting process of those concentrate all gold and silver are practically in the blister copper, which is cast into anodes. Those copper anodes are electrorefined in an electrolytic system, where the electrolyte is an acid copper sulphate solution, where a high purity electrolytic copper is produced (>999,9/1000). The slime when submitted to an oxidative leaching process, using sodium hypochlorite and hydrogen peroxide as oxidizing agents, turn those metals into solution. This research practical work, apart from concentrating effort on the digestion of the anode slime, aims at evaluating the efficiency of the cementation process of the metals of interest for the separation of them to take place. 141

Jan 1, 2008

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008