Search Documents

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

By Neil E. Izatt

The use of Molecular Recognition Technology (MRT), a selective separations technology using specifically designed ligands, has been established as an effective process for removal of metal ions found in many hydrometallurgical, chemical, and wastewater streams. The MRT process has been proven to be highly efficient and effective for indium extraction and recovery from zinc acid leach, electrolyte, chemical process and waste streams. A high percentage of the indium is recovered in a solid product format. MRT has also proven effective for germanium extraction and recovery from similar feed streams. This paper provides the indium and germanium metal recovery flow sheets and analytical results of the metal load and recovery steps.

Jan 1, 2006

By J. Brent Hiskey

The global copper industry faces a technological challenge to develop processing schemes for more complex and impure ores and concentrates. Group 15 elements (As, Sb, and Bi) represent impurities that are troublesome both in terms of environmental impact and metallurgical processing. The so-call "dirty" copper concentrates are either unacceptable for smelting and refining or incur high penalties. The behavior of the Group 15 elements is of critical importance in maintaining product quality and process performance. During copper electrorefining, these impurities are released to the electrolyte by electrochemical dissolution of the anode. Depending mainly on temperature, concentration, and oxidation state these elements can spontaneously coprecipitate from the electrolyte. Some of these precipitates are referred to as floating slimes and their formation can have extremely detrimental effects on cathode purity. In this paper, the mechanism of floating slimes formation will be discussed and the fundamental thermochemistry will be reviewed and analyzed in relation to solubility properties.

Jan 1, 2012

By T. Xin

A vertical grain boundary intercepting a horizontal free surface forms a groove to reduce the combined surface energy of the system. We study grooving by surface diffusion with anisotropic surface energy. A recently developed delta-function model of facets is used to describe the surface energy with three or four fold symmetry. It is found that the groove grows following a similarity law. The self-similar groove profile is solved numerically by a shooting method. Even with strong anisotropy, the groove profile can be smooth if the exposed surface orientations do not include a facet orientation. The smooth self-similar groove shape is the same as an isotropic groove, but the size is reduced by a factor that depends on the degree of anisotropy. This induces a large error on the value of surface diffusivity if the isotropic model is used for an anisotropic system. In this talk. we will describe how to correct for this error.1 I Xin, T. and H. Wong, "Grain-Boundary Grooving by Surface Diffusion with Strong Surface Energy Anisotropy," Acta Materialia 51, 2305-2317 (2003). Keynotes: Grain growth, Surface Diffusion, Surface energy, Anisotropy

Jan 1, 2003

By Dachun Liu, Wenlong Jiang, Baoqiang Xu, Yongnian Dai, Bin Yang

"In the traditional method for refining of indium, glycerin-KI and glycerin-NH4Cl are used as electrolytes to remove Cd and Tl by electrolytic refining, which produces In with a purity of 99.995%. Large quantities of polluted industrial waste water are the result. It is calculated that the saturated vapor pressure of Cd and Tl are between 1-200 Pa, which is much larger than the vapor pressure of In. Thus, the study of removing Cd and Tl was carried out over the temperature range between 700-950 °C and pressures between 1-15 Pa. After vacuum distillation the contents of Cd and Tl in crude indium could sharply fall below 1 ppm..IntroductionIndium is a is a pale blue and silver white metal, and has high ductility [1-2]. Pure indium is generally used as a raw material to produce semiconductor compounds, fluorescent material and ITO targets [3]. Sublimation, zone melting and electrolytic refining are major methods to produce pure indium from crude indium. Electrolytic refining is the main method to product pure indium at present. High productive efficiency, simplicity of operation and short cycle of production are major advantages. However, glycerin-KI and glycerin-NH4Cl are used to remove Cd and Tl in electrolysis method. Large quantities of polluted industrial waste water are the result[4]."

Jan 1, 2012

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By Pedro A. Netto, Sergio N. Monteiro, Foluke S. de Assis, Rômulo L. Loiola, Frederico M. Margem

Banana fibers are among the lignocellulosic with great potential for use in polymer composites, such as the variety from the Musaceae family, due to its low density and good mechanical properties. In this work, epoxy matrix composites incorporated with continuous and aligned banana fibers were tested for their flexural behavior. Specimens with up to 30% in volume of fibers were bend-tested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractographic analysis by SEM examinations a moderate adhesion mechanism between the banana fiber and the epoxy matrix. This mechanism is apparently responsible for the improved performance of the composites.

Jan 1, 2015

By Georgeta Rata, Cornelia Petroman, Ioan Petroman

"Proper training and education in the field of recycling and waste treatment are inconceivable without the proper teaching of the terminology specific to both recycling (aerospace products recycling, automotive recycling, general recycling, recycling behaviour, recycling schemes, recycling systems, and waste recycling) and waste (characterization of waste, electronic waste, heavy-metal containing waste, monitoring of waste, radioactive waste, solid waste, waste collection, waste conversion, waste recycling, waste reutilization, waste stabilization, waste storage, and waste treatment) in both the students’ mother tongue and in English for Special Purposes (ESP) as a second language (with focus on the structuring of the specific terminology). Including linguistic approaches among the possible approaches of environmental protection and material sustainability means including linguistics among the various disciplines addressing energy supply, cement and building materials, metallurgy, chemistry, glassware, pulp and paper industry, machinery, automobile and electronic industries, collection, and sorting, further treatment and final disposal of post-consumer material.IntroductionCultural and technical changes have produced more novel artefacts than novel activities or novel properties, generating new vocabulary needs that are readily answered by new words (nouns).The purpose of this research is to show that ‘waste words’ – phrasal words (items that have the internal structure of phrases but function syntactically as words, e.g., cattle waste) and particularly compound nouns (words formed by combining roots, that tend to have a meaning that is more or less idiosyncratic or unpredictable, e.g., wastepaper ‘discarded paper’) – used in the study of the English of recycling, waste treatment, and clean technologies can be misleading for both native and non-native students and/or users of English because their structure alone does not allow instant, proper understanding of their meaning.Our hypothesis is that this inconvenient can be overcome by getting to reach the proper meaning of these new words. Or, arriving at the precise meanings of the ‘waste words’ depends on our knowledge of the world (for example, wastepaper indicates that some used paper is discarded and not wasted) rather than on purely linguistic knowledge."

Jan 1, 2008

By A. S. Mustafinova, A. A. Zharmenov

"Production of electrolytic copper is characterized by large volumes of acidic spent solutions the utilization of which requires considerable expenditures of neutralizing agents. At present, an economically substantiated technology does not exist for treatment of sulfuric acid rinse solutions and spent copper electrolyte which will allow for repeated use of the acid and the metal salts. Therefore, for this aim the most advantageous is the use of electromembrane methods. In the paper there is stated the essence of developed technologies which are distinguished by low waste and provide the extraction from the solutions of metallic copper, nickel and sulphuric acid. There are also considered methods of copper electrolyte processing allowing to regulate its composition by that or another component (H2S04, Cu, Ni, As).On the base of the detailed study of the behaviour of various types of ion- exchanger membranes in copper-, nickel-, zinc-, arsenic- bearing sulphate solutions there is realized the selection of the most suitable membranes (MK -401, MA-411, MB-2 and MKL-l/MAL-2).Some variants of electro membrane processing of spent solutions of the hydrometallurgy process have passed productions tests on a number of copper-electrolyte enterprises of the countries of CIS (cooperation of Independent States). These tests showed high efficiency of developed methods."

Jan 1, 1997

By Gunther Schimmel

Ag exudation in four different alloys (Ag-Cd, Ag-Sn, Ag-Sn-In and Ag-Zn) is characterized. The amount of exuded material is correlated with the volume increase due to oxide formation in dependence of the alloy concentration and different densities of the oxide and matrix phases. It is shown that all four alloys show similar amounts of volume increases, but different amounts of exuded material. It is concluded that internal stresses due to the volume increase cannot be the dominant driving force for Ag exudation. A gradient in the chemical potential of Ag that originates from the O concentration gradient inherent to internal oxidation is suggested as driving force. The exudation behavior is thus governed by the variation of the activity of Ag in the Ag fcc phase in the Ag-Me-O system that differs between the alloying systems.

Jan 1, 2010

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By Guiming Yang, Xiaoxian Huang, Zhiyun Ji, Min Gan, Lishun Yuan, Xiaohui Fan, Zhiyuan Yu

"The roasting characteristics of hematite pellets containing MgO were studied where magnesia powder, serpentine and magnesite were used as magnesium-additives respectively. The mechanical strength of both preheated and roasted pellets decreased when MgO content increased, which implied the addition of MgO had an adverse effect on pellet consolidation. By adding flux containing CaO, the mechanical strength of both preheated and roasted pellets were improved. The addition of calcium flux facilitated the formation of calcium ferrite and provided a certain amount of liquid phase, resulting in faster diffusion ofMg2+ and Fe3+. The result showed that diffusing speed of Mg2+ was enhanced by 1.48 times, and rate constant of Fe203 crystalline growth was enhanced by 62% when basicity was around 0.4. Improvement of mineralization degree and recrystallization of Fe203 assisted in consolidation of hematite pellets containing MgO.IntroductionOxidized pellets are ideal iron-bearing burdens in blast furnace. At present, magnetite is the main raw material for oxidized pellet production in China. However, as the rapid development of iron and steel industry, resources of magnetite have been depleted and cannot satisfy the requirement of pellet production. Using hematite concentrates to produce oxidized pellets has become a trend [1, 2]. Many pellet enterprises abroad nowadays have adopted high proportions of hematite concentrates when producing oxidized pellets, e.g. the percentage is 100% in a lot of Brazilian factories [3, 4]. But high proportion of hematite concentrates will lead to low mechanical strength and high reduction swelling index of pellets. Some studies show that Mg-bearing pellets have excellent metallurgical properties, and the reduction swelling phenomenon can be solved by adding fluxes containing MgO [5, 7]. However, there are problems such as low pellet strength and bad roasting characteristics for MgO-bearing pellets, which remains an obstacle in pellet industry. Hence, it's vital to undertake the study on strengthening measures for indurations of Mg-bearing hematite pellets."

Jan 1, 2013

By Rauf Hurman Eric

The high temperature liquid miscibility gap in the Ag-Ag2S pseudobinary portion of the Ag-S system has been redetermined by very carefully conducted equilibration-quenching experiments. Samples were contained in evacuated and sealed silica capsules. The stratified liquid phase compositions were obtained by chemical analysis. The miscibility gap extends from 14 to 32.3 atomic percent at the monotectic temperature of 906°C and closes at around 1320°C.Thermodynamic properties of the liquid solutions, including the limiting activity coefficient of sulfur in molten silver were expressed analytically by using the sub-regular solution model which proved to be in excellent agreement with the experimental findings.

Jan 1, 2006

By David A. Army

Many times, the maintenance professionals have been involved in changes to processes or systems. Often they rely on seat of the pants knowledge to determine whether or not they were successful. More often than not, once our attention has been turned to other endeavors, the initiative has floundered. This paper will describe those measures that can be most effectively used to track and manage the success of implementing an improved Work Management System. However, not only will the paper discuss traditional work indicators, it will also explain how to establish the behaviors in the work place that will ultimately ensure successful implementation. Combined with the discussion on indicators will be a discussion on how to tie them to bottom line results and display them in the form of a scorecard. Actual results will be discussed.

Jan 1, 2006

By K. Kashiwaya, N. Hiroyoshi, H. Furuya, N. Sumiya, M. Tsunekawa, M. Ito

"The number of hybrid vehicles is increasing and this is causeing an increase in waste nickelmetal hydride batteries. The cathode activating agent of batteries is made of nickel hydroxide and the anode activating agent is an alloy of nickel and rare earth elements. Conventional rotary kiln methods cannot recover the rare earth elements, and hydrometallurgical treatment of crushed product consumes large volumes of agent. The physical separation of the anode alloy from the cathode hydroxide would make it possible to reuse the alloy. The authors have reported separation of anode and cathode components in the large size fractions using a newly developed dry magnetic separation method. Wet magnetic separation has been applied to the powder fraction and about 90% anode purity was achieved. This paper reviews experimental results from previous publications and proposes an integrated treatment process for crushed nickel-metal hydride batteries.IntroductionEnvironmentally-conscious clean energy vehicles have attracted much attention in developed countries and particularly hybrid vehicles are increasingly mass-produced as low emission vehicles. Hybrid vehicles have both a gasoline engine and an electric motor to save on gasoline usage and a nickel-metal hydride battery is used to store electric energy. The battery contains Nihydroxide and Co as the cathode activating agent and an alloy of Ni and mischmetal (mM), a rare-earth element mixture consisting of La, Ce, and Nd, as the anode hydrogen adsorption component. In conventional recycling, the Ni and Fe are recovered with a rotary kiln-electric melting process and the Co and mM go to the slag component [1] and hydrometallurgical treatment of crushed product consumes large volumes of agent. Japan Oil, Gas and Metals National Corporation have proposed a low energy and low cost recycling treatment process combining the physical and chemical treatments and the authors are investigating the physical treatment process."

Jan 1, 2008

By J. C. Agarwal

Rare earth metal alloys are becoming increasingly important, particularly those of neodymium, because of their magnetic properties. This paper will present a generalized approach to the production economics of the metallic rare earth alloys. With appropriate regard for the chemistry of different rare earths and the large impact of economies of scale, it is possible to make fairly accurate estimates of the production costs of other rare earth alloys as well.

Jan 1, 1989

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

By Yasuhiko Ito

"This talk is concentrated on the topics of compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate. As a typical example, electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film is described. Another example is the formation of various kinds of intermetallic compound films including Ni2Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail.IntroductionGenerally speaking, surface film formation by molten salt electrochemical process can be divided into the following three categories:(i) single element film formation on the electrode by electrodeposition,(ii) compound film formation on the electrode by electrocodepostion of more than two elements, and(iii) compound film formation on the substrate electrode by interdiffusion of substrate element and electrochemically deposited species and/or by direct electrochemical implantation of the component element of the film into the substrate.This talk is .concentrated on the topics of category (iii), especially on the electrochemical implantation. Typical example can be seen in the electrochemical implantation of nitrogen atom into Ti metal to form TiN surface film. Another example is the formation of various kinds of intermetallic compound films including Ni2 Y, Ni2Dy and Pd3 Y by the electrochemical implantation of lanthanoid elements into transition metal electrodes. By combining these two methods, Sm-Fe-N ternary material film also could be formed. The principle and application of the ""electrochemical implantation"" are discussed in detail with examples above as well as other experimental results also obtained very recently in the author's laboratory."

Jan 1, 2000

By Andrew Shabalin, Vladimir Skorohodov, Svetlana Babaeva, ?lga Makovskaya

"At processing of some kinds of wastes (electronic scrap, secondary materials, spent nuclear fuel) in nitric acid solutions, and also in technology of silver refining, the significant amounts of palladium and platinum passes into a solution. The ion-exchange concentration of palladium and platinum in nitric acid solutions (5-500/dm3) are investigated. More than 30 various classes of ionites are tested. The most chemically resistance resins at the given conditions are identified. It is shown, that the maximum sorptive capacity to studied metals at high acidity the complexing, synthetic and inorganic sorbents possess. To definition of platinum metals sorption optimum conditions the kinetics is studied, isotherms of a sorption at various parameters from nitrate solutions are obtained. The conditions of the platinum and a palladium desorption from the pregnant sorbents and its regeneration with the subsequent reuse of materials were defined. The raw materials containing precious metals have very diverse composition and physical properties. Commonly the materials are processed by hydrometallurgical way. If gold or PGMs there are in raw materials to its opening hydrochloric acid solutions are applied. As an oxidizer nitric acid, hydrogen peroxide, gaseous chlorine, etc are used. Nevertheless, at processing of argentiferous materials and preliminary treatment of a waste including the spent nuclear fuel, nitric acid solutions are often used and the specified metals in some extent pass into solution [1]. Therefore selective extraction of PGMs from nitrate solutions is an actual problem. In the present work the ion-exchange concentrations of palladium and platinum in nitric acid solutions (5-500 g/dm3) are investigated. At the testing more than 30 various classes of ionites the most chemically resistance resins at the given conditions are identified. These resins are synthesized on the base of polyacrylate, styrene-divinylbenzene and vinylpyridine. For a selection of the most effective resin among what are made in Russia and overseas, a number of ionites with various functional groups were studied. Influence of functional groups type on a PGM sorption is shown for extraction of a palladium as an example (table 1). The presented data shows, that palladium concentration in a phase of ionites depends on sorbent type. If the increasing of solution acidity essentially reduces palladium sorption by sulfonic cation-exchange resins (KU-2×8) than its sorption by strongly basic anionites is approximately equal. Intermediate position is occupied by complexing sorbents. The latter (AN-31, SN-3, ANKB-35, Lewatit TP 207, Purolite S 930) are the most effective for extraction of PGMs from nitrate solutions from the point of view of capacity value. According to [2], solution behavior of Pt (II) and Pd (II) are similar. As is known from coordination chemistry, ligand environment of the metal ions substantially impacts to character of electronic spectra. The figure 1 shows the results of measurements of optical density of platinum bearing solutions with various concentration of nitric acid at ?=400 nanometers"

Jan 1, 2008