Search Documents

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By R. E. Moore

The lining systems currently in use in BOF furnaces, certain steel ladles, and the slag line of electric are furnaces were developed during the late seventies through the mid-eighties using a trial and error method of combining aggregate, carbon sources, additives and binders. They are currently based on magnesia, graphite, metal additives and resin binders, the selections of each being tied to the anticipated intensity of the use conditions. The general functions of the respective constituents are well appreciated, however, there is still a great deal that is not known about how the socalled antioxidants protect the graphite nor how impurities from the graphite and the aggregate enter into the wear processes. In a simplified assessment of wear processes, it appears that if the deoxidized layer can be kept very thin, less than 810 mm in depth, and if the viscosity and quantity of the matrix glassy phases can be controlled to resist erosion of the deoxidized layer, lining life can be maximized for the various applications. This paper will discuss the characteristics of the starting materials systems currently being employed for applications requiring a deoxidation function to realize extended wear. It will not attempt to explain all the complex interrelationships between the respective constituents but will point to the potential for improvements through the use of improved constituents.

Jan 1, 1991

By David R. Jessey

An ore microscopic and geochemical study of the nickel-cobalt occurrence in the Southeast Missouri Mining District has revealed several significant relationships. Siegenite [(Ni,Co)3S4] is the dominant nickel-cobalt sulfide in the ores, however, several other members of the thiospi¬nel group (AB2S4) occur: carrollite (CuCo2S4), nickelean carrollite [(Co,Ni,Cu)3S4], fletcherite [Cu(Ni,Co)2S4] and polydymite (Ni 3S4). In addition, bravoite [(Ni,Fe)S2], vaesite (NiS2), millerite (NiS) and gersdorffite (NiAsS) are present. Thiospinel composition varies dramatically within the district. Paragenetic studies have shown that the stratigraphically lowest thiospinels are the most cobalt-copper-rich. A detailed ore microscopic study of the AMAX Lead Company Buick mine has also shown significant changes in mineralogical association, texture and grain size of the siegenite along the north-south strike of the major ore bodies. Siegenite commonly replaces and veins chalcopyrite and is subsequently replaced by sphalerite. Less commonly, siegenite and chalcopyrite are observed to form linear replacements along sphalerite grain boundaries. The grain size of the siegenite varies markedly, but in a predictable north-south pattern that is consistent with a genetic model formulated from geo-chemical data. The compositional as well as textural trends displayed by the thiospinel mineralization could be exploited to optimize recovery of any or all thiospinels of economic interest.

Jan 1, 1981

By Lichao Ding, Jingbiao Fan, Yunnen Chen

"With the development of industrial production, more and more wastewater containing high concentration ammonia nitrogen was discharge into the environmemt, which caused serious harm to the environmemt. Treating the wastewater has great significance to protect water resources. Using air-stripping combined with oxidation to uptake high concentration of ammonia nitrogen wastewater. The influence of operating parameters was investigated. Experimental results revealed that pH of solution, aeration time and aeration strength showed heavy influence on ammonia nitrogen removal. Air-stripping combined with oxidation can be considered as an alternative approach for the removal of high concentration of ammonia nitrogen from practical metallurgical wastewater. When pH was 11, aeration time 20 min, aeration strength 1040 Lh-1, and oxidation with 10 % NaClO solution 10 min, the initial ammonia nitrogen 2130 mgr1 could reduce to 12 mgr1. Other items could also be removed to meet the ""Integrated wastewater discharge standard (GB8978-88)"".1. IntroductionThe rapid development of human activities has caused a worldwide increase of nitrogen in rivers, lakes and coastal waters. It leads to considerable eutrophication and an increase in the frequency of toxic algae blooms [1,2]. The concentrations of nitrogen in the water of China are pervading high [3]. The discharge of wastewater containing high concentration of ammonia nitrogen is one of the most important factors. Great efforts have been devoted to the removal of ammonia nitrogen from wastewater. Traditional methods include biological denitrication [ 4 ], chemical precipitation with magnesium ammonium phosphate [5], electrochemical conversion [6], air-stripping [7] and so on. Biological denitrication is the most common process in the treatment of ammonia nitrogen wastewater. But the process is only suitable for the removal of relatively low ammonia concentration due to the requirement of appropriate C/N ratio [8]. Chemical precipitation needs additional reagents, which may introduce new pollutants to water body. Electrochemical method often uses expensive metal or metal oxide as electrodes, and also consumes large quantity of energy [6].Although air-stripping makes use of stripping tower and consumes energy, it is very suitable for the removal of relatively high ammonia concentration. Different air-stripping conditions would appear different removal efficiency. And only air-stripping the effluent can not be attained the ""Integrated wastewater discharge standard (GB8978-88)"". In this study, we use air-stripping and oxidation to removal high concentration of ammonia nitrogen from simulated and real ammonia nitrogen wastewater."

Jan 1, 2011

By F. E. Pawlek

Copper concentrates can be comminuted in an attritor within a very short time to a particle size of 1 - 0.1 um. Addition of sodium hydroxide enhances commninution. The concentrates, suspended only in water, can be completely dissolved under oxygen over pressure and temperatures ranging from 120 - 180°C (248 - 356°F), because the surface area of the concentrate has been significantly increased by the ultra fine grinding. Addi¬tion of a small amount of silver ions to leach liquor containing sulfuric acid acted as a catalyst for the dissolution of chalcopyrite, because of the formation of local elements on the surface. The addition of C1- ions was also catalytically very effective. With this method it is possible to completely dissolve the copper contained in chalcopyrite concentrates after ultra fine grinding within 30 min at 110°C (230°F) under an oxygen partial pressure of 1 atm (14 psig). Several flowsheets demonstrate the industrial feasibility.

Jan 1, 1976

By Jeffrey L. Zelms

Environmental issues and how they are addressed -- or not addressed -- by the lead industry in the 1990s will determine the eventual fate of lead mining in both the U.S. and worldwide. Clearly, governmental regulation throughout the West will become harsher. Equally clearly, the industry has? failed to educate the public regarding lead. Instead of public support for a critical mineral, we face widespread public ignorance and paranoia. If we can demonstrate the public interest benefits of the industry, the 1990s will be a decade of continuing growth -- not dynamic growth, certainly, but growth at least comparable to the world economy. If, however, we fail to demonstrate the industry's public interest benefits, the 1990s could mark the beginning of the end of our business.

Jan 1, 1990

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderurgica Belgo Mineira, Joao Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Mrutyunjay Panigrahi, Takashi Nakamura, Atsushi Iizuka, Etsuro Shibata

"The production of FeTi intermetallic alloys from mixed oxide precursors using direct electrolytic reduction was studied. Fe203 and Ti02 powders were mixed in appropriate molar ratios, pressed into small pellets, and then heat treated at temperatures in the range 1000-1300°C. The pellet heat treated at 1000°C was electrolyzed in molten CaCh at 950°C, using a graphite crucible as the anode and the oxide pellet as the cathode, at a potential of 3.0 V. The products of the electrolytic reduction of (Fe,Ti) oxide were examined by XRD, SEM and EPMA. It was found mat the (Fe,Ti) oxide was reduced progressively from the outside to the inside of the pellet until the metallic state was achieved.IntroductionFast and energy-efficient technologies for materials production are essential for the sustainable development of society, and such development is supported by advanced technologies. Since the introduction of titanium and titanium alloys in the early 1950s, these materials have, in a relatively short time, become major materials for the steel, aerospace, energy, and chemical industries. Its combination of a high strength-to-weight ratio and excellent mechanical properties and corrosion resistance make titanium the best material for many critical applications [1]. Titanium alloys are now used in demanding applications such as static and rotating gas-turbine engine components. Some of the most critical and highly stressed civilian and military airframe parts are made of titanium alloys. The use of titanium has expanded in recent years to include applications in nuclear power plants, oil-refinery heat-exchangers, marine components and medical prostheses.Ferrotitanium is one of the most widespread and effective ferroalloys. It is also a well-known hydrogen-storage material and will be extensively used in the future because hydrogen is emerging as an eco-friendly energy source [2], Ferrotitanium is an alloy consisting of iron and titanium, with a minimum titanium weight content of 20% and a maximum titanium weight content of 75%, and is manufactured by reduction or melting."

Jan 1, 2012

By A. G. Merma

In this work, the electrocoagulation technique was studied in order to treat chemically stabilized concentrated oil-water emulsions. This study was mainly focused on the effects of operating parameters such as initial pH, current density, reaction time, electrode distance and inlet concentration on the separation of oil as measured by the chemical oxygen demand -1(COD) method. The synthetic emulsion was prepared from Shell - Talpa 30 oil (3g.L-1) and sodium dodecyl sulfate (1.0 g.L), having a Zeta potential around -70 mv at pH 8.7. The process was carried out in an electrocoagulation cell with a set of four parallel monopolar electrodes. This set consisted of two aluminum plate anodes and two 316L stainless steel plate cathodes. Kinetic curves showed that the electrocoagulation process exhibits three phases: (1) an initial phase, where the COD did not decrease because the solution had not reached the minimum amount of dissolved aluminum required to cause the break-up of the emulsion, (2) a reactive phase during which COD decreased due to possible agglomeration of the precipitates and (3) a steady-state phase where the COD did not change. The results showed that the period to reach the reactive phase decreased as the current density increased and the pH values decreased.

Jan 1, 2009

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Chris Twigge-Molecey

As emission constraints for metallurgical plants become more difficult to meet; control of major, multi-vessel, flue systems become more critical. Control instabilities can result in significant loss of system capacity or emissions to the environment. This paper will discuss the use of dynamic simulation techniques to optimize both the design and control strategies for these systems. A significant ,safety hazard is associated with pressure excursions from process upsets or equipment failures. Pressure rise rates of up to 10 kPajsec can occur. These cannot-be followed by conventional controls. Fail-safe high speed venting is required to protect both the furnaces and operating personnel'. Design options, sizing techniques and practical problems are discussed.

Jan 1, 1992

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999