Search Documents

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

By R. W. Harnmack

Hydrogen sulfide generated by the anaerobic respiration of sulfate-reducing bacteria was used to treat pH 2.2 water from the abandoned Rio Tinto copper mine in Nevada. The untreated water contained 550 mg/L Fe, 140 mg/L Al, 90 mg/L Cu, 80 mg/L Mn, 60 mg/L Zn, 4 mg/L Co, and 2 mg/L Ni. The bench-scale treatment system examined consisted of a bioreactor for H2S generation and three precipitator/clarifier units for metal sulfide precipitation and recovery. The treatment system reduced the concentrations of all metals except Mn to less than 0.1 mg/L. Manganese concentrations were reduced by 96 percent to 3.3 mg/L. A CUS/SO concentrate (33 pct Cu) and a ZnS/5° concentrate (28 pct Zn) were produced that may be suitable for metal recovery at existing smelters

Jan 1, 1994

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By David Cocke

Study of surface and subsurface interfacial chemistry of metallic and similar systems has its enormous technological importance. Copper, for example, is a common component of many alloys and bulk amorphous systems. It is being increasingly studied today because of its use for electronic interconnect systems where processing is done below 200 ºC. Since several types of copper oxides exist, and the degree of their formation is dependent on temperature, perhaps characterization by EDS-SEM depth profiling and EIS might delineate one type of oxide from another. In this paper, we described our work on transformation of copper oxides with temperature ranging from 70 to 350 °C and their characterization by SEM, EDS, and XRD. We also showed the use of the phase angle portion of the impedance as a means to identify the predominant structure and the transition through Cu3O2 between the predominant stable CuO and Cu2O.

Jan 1, 2009

By M. E. Huckman

In this paper, we review the equations needed to construct an ion exchange column model. These models contain three major components: 1) a differential material balance around the colunm, 2) a differential material balance around an ion exchange particle, and 3) a constitutive equation for diffusive flux We then examine the ability of a fairly simple mathematical model to predict ion exchange column experimental data. This model contains the traditional absorption theory equations and is used to predict the behavior of a column filled with a hydrous crystalline silico-titanate and which is removing trace amounts of Cs+ from a high pH, complex electrolyte solution. Finally, we propose replacing Fick's law with the Nernst-Planck equation as the constitutive equation for diffusive flux We use a Nernst-Planck type model to predict batch experimental data, then evaluate it by comparing it's ability to predict experimental data to that of a more traditional Fick's law type model? The data from this comparison suggests that the Nemst-Planck type model yields better results.

Jan 1, 1996

By Osamu Iida

In the Mitsubishi converting furnace (C-furnace), molten matte continuously undergoes intensive conversion into blister, and an excess amount of heat is generated, even after taking into account heat loss from the furnace, off-gas, and latent heat of melt. To absorb excess heat in C-furnace, recycled granulated converting slags (C-slag) were wastefully charged in the C-furnace. In contrast, supplementary coal is necessary to make up a shortage of reaction heat in Smelting furnace (S-furnace). To utilize the excess heat of the C-furnace effectively and accommodate the unbalance of heat utilization between S and C furnaces, three technological innovations had been carried out. ? Spent anode charging facilities in C-furnace was modified, in order to solve some spent anodes hitting and eroding the hearth bricks. ? Cubic pressed copper scrap charging facilities were installed in C-furnace. ? Facilities were newly installed in C-furnace to treat neutralized residue from the wastewater and dust treatment plants, previously treated in the smelting furnace. Above innovations led to the further effective utilization of heat, increase in production, and savings in energy costs.

Jan 1, 1999

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By Akira Yazawa

Experimental results for the distribution ratios of various elements between the slag, matte and/or copper in the silica-saturated copper smelting system were summarized. The experiments were carried out under an oxidative smelting condition with S02 gas flow, and also a reductive smelting condition equilibrating with metallic copper or iron. To evaluate the results thermodynamically, the availability of one atom cation base expression for the constituent compounds is emphasized from both of theoretical and practical standpoints. Both of oxidic and sulfidic dissolutions in slag are postulated for some elements such as copper, nickel and lead., and the experimental results are reasonably explained thermo-dynamically. The results for the mutual solubility between matte and ferrite slag and the distribution of minor elements between liquid copper and ferrite slag are also discussed.

Jan 1, 1983

By Jun Li, Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial of direct modification of molten blast furnace slag and production of high acidity coefficient slag wool fibers were investigated nearby a blast furnace. Molten blast furnace slag discharged from blast furnace and then directly flow into specialized modification furnace and quartz was simultaneously added into the molten slag as modification agent. The modified molten slag was electric heated to 1500–1550 °C and then the melt was produced into slag wool fibers through high-speed centrifugation method. Melt with acidity coefficient of 1.2, 1.4, 1.6 and 1.8 were investigated and fibers with corresponding acidity coefficient were produced. Slag wool fibers with shot content of 5.5, 5.8, 6.2, 6.8% and average diameter of 4.5, 4.9, 5.6, 6.4 lm for four samples were successfully produced, respectively. Total energy consumption and production costs decreased by 50–70% compared to traditional cupola furnace method. This method provides an energy-saving and emission-reduction technology for the direct utilization of molten blast furnace slag.

Mar 1, 2018

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By C. Hakan Gür

Optimization and control of the microstructure is important for improving the properties of steel components. Development of non-destructive techniques for microstructure characterization is a critical task. Magnetic Barkhausen Noise (MBN) technique is a promising and challenging non-destructive technique fo automated evaluation of microstructures in steel components in a fast and reliable manner. This paper presents the results of MBN measurements for microstructure characterization of the quenched and tempered steels.

Mar 1, 2017

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By T. Alboussiere, O. Paireau

"We have designed an experiment to simulate natural convection in a direct-chill aluminium ingot. In this experiment we induce natural convection within a hemisphere filled with liquid-metal (mercury). The device consists of a copper hemispherical bowl closed by a copper plate. The top is maintained at superheat temperature while the boundary is cooled. While the temperature measurements were found using thermocouples, the velocities were obtained using an original technical procedure that relies on MHD properties. By applying a steady local magnetic field, we measure the velocity. The distribution of temperature and velocity can be separated into a thermally stratified core bounded by thermal wall jets. These wall jets greatly influence the degree of macrosegregation in ingots.1. Natural Convection in Aluminium CastingIt is well known that the quality of the final product in aluminium casting depends on the movements within the liquid metal such as forced or thermogravitational convection. Strong buoyancy-driven flows are known to occur in the liquid metal pool of an aluminium ingot caster. These flows have a significant influence on the metallurgical structure of the ingot through the redistribution of heat, fragmented dendrites and segregated material within the pool. Macrosegregation mechanisms depend on favourable temperature and flow distributions in the sump, and these factors will determine the pattern and degree of macrosegregation. Moreover, for many years, the importance of thermally-driven natural convection in casting has been underlined (Cole & Bolling, 1965). In this way, a precise determination of the velocity and temperature fields is required in order to improve understanding of the macrosegregation mechanisms. That is precisely the aim of this paper, which provides experimental data of the flow and the temperature distributions in a natural convection experiment. We intend, with this laboratory experiment, to determine accurately the velocity field, particularly within the thermal boundary layer where the effects of the flows may have an important role in the transport of crystals."

Jan 1, 1999

By Yuan Lu, Yiming Rong, Richard D. Sisson Jr

With the development of quench technology, there is a trend of using gas quench to replace liquid quench for less distortion and residual stress. The fundamental difference between the liquid and gas quench is the heat transfer coefficient, not only the values but also the shape of the curve as a function of temperature. The equivalent heat transfer coefficient for the liquid and gas quench is analyzed by simulations and experiments. Even it may result in the same hardness in the liquid and gas quench, the steel microstructure may be different because of the different cooling processes, and therefore other steel properties, such as toughness, may be different. The cooling process, microstructures and properties such as hardness and toughness should be examined when designing the liquid or gas quench processes.

Jan 1, 2015

By James Bennett, Jinichiro Nakano, Anna Nakano

Efficiency of the chemical looping combustion technology is adversely influenced by surface properties of oxygen carrier materials during oxidation–reduction process changes at elevated temperatures. In this work, natural hematite (Fe2O3) and alumina (Al2O3) supported Cu-spinel (CuFe2O4) oxygen carrier particles were isothermally exposed to redox gas cycles (air and 10 vol% CO–90 vol% Ar) at approximately 800 °C and studied using a high temperature confocal scanning laser microscope for real time alterations in surface morphology, roughness, and particle volume. 3D topological scans from each cyclic gas exposure indicated hematite particles exhibited noticeable volume expansion in reduction and shrinkage in oxidation, corresponding to respective phase transformations. Materials surface changes during the redox gas cycles are discussed.

Mar 1, 2017

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000