Search Documents

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of 873°K is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composition formed under roasting of concentrates with particle sizes less than 0.02 um (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CuFeSz2 each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forchamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By Li Yuhai

Kinetics of non-isothermal precipitate process and crystal growth of perovskite (CaO ? Ti02) phase in CaO-TiOz-Si02-AlP3-MgO system were studied. The experimental results show that the relative volume fraction can be described by the equation given by K. Matusita et at. and the experiential expression of average crystal radius was obtained. The particle coarsening in non-isothermal process has important effects on the crystal growth of perovskite phase.

Jan 1, 2000

By Zhi Yang, Ahmad Ghahreman, Farzaneh Sadri

Impurity removal is a very important stage of the hydrometallurgical treatment of rare earth elements (REE) processing circuit, which is performed after water leaching of the acid baked REE concentrate. Lime neutralization has a high efficiency in removal of impurities and is the preferred process due to its economic advantage; however, the process has its own problems, such as the production of large volumes of gypsum and co-precipitation of REE with gypsum, i.e. REE loss. This work deals with the effect of several additives (cetryltrimethylammonium bromide (CTAB), polyvinylsulfonic acid (PVS) and polyacrylic acid (PAA)) on the uptake of REE by gypsum from synthesized acidic solutions. The main purpose of this study is to investigate the changes in the crystalline morphology of gypsum precipitated by the addition of crystal habit modifiers and to determine the crystal changes’ effects on the uptake of REE by gypsum. In this regard, different concentrations (0.2, 2 and 5 g L−1) of above-mentioned additives were studied at room temperature.

Mar 1, 2018

By M. D. Stephens

A new, one-step process for extracting titanium from titaniferrous materials has been demonstrated. In the process, depleted uranium tetrafluoride (DUF 4), a solid, is mixed with ilmenite (FeTi03) and heated to 900°C. Titanium is extracted in the vapor phase as titanium tetrafluoride (TiF4) and the DUF4 is converted to uranium-iron oxide. The process has been found to selectively fluorinate the titanium in ilmenite and is capable of producing high purity TiF 4 with very low iron content. TiF 4 can be collected by condensation or through reaction with a fluoride salt such as NH4F, KF, or NaF. The TiF4 produced from the process can be used to make titanium metal, titanium oxide, or fluorotitanate compounds. Since the fluorination process is highly selective for titanium, it avoids many of the separations and waste issues common to other titanium extraction processes.

Jan 1, 2001

By Zdzislaw Miczkowski

At KGHM Polska Miedz S.A, a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass exchange inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed, The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ?The second zone moves slower into the grain and the rate of the movement is determined by the presence of oxygen, In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined, The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Afrodite Ntziouni, Vassilia Kasselouri – Rigopoulou, Athanasia Kyritsi, Konstantinos N. Pistiolas, Stamatia Gavela, Konstantinos Kordatos, Lazaros Iliadis

"The present study deals with the production and characterization of rice husk ash (RHA) and its use in the synthesis of zeolite of type ZSM-5. Rice husk was combusted in various temperatures with aim to find the suitable conditions for the production of amorphous silica. The resulted amorphous silica ash was then utilized as a starting material for the synthesis of ZSM-5 zeolite using the low temperature and atmospheric pressure process. The method led successfully to the synthesis of highly siliceous zeolite of type ZSM-5. The produced material was characterized using x-ray diffraction (XRD) and scanning electron microscopy (SEM).IntroductionRice husk is a major by-product of the rice-milling industries and it is usually used as a fuel for steam generation due to its high calorific power. During its combustion, rice husk ash (RHA) is produced. Knowing that the annual rice world production is over 615 million tons (2005), thus resulting in a potential production of more than 22 million tons of RHA [1], it can be understood that the RHA disposal is a crucial issue towards the environmental protection. However, due to the high silica content, RHA can be used as an alternative cheap source of silica for many uses, including as filler in polymers [2], concrete [3] and synthesis of zeolites [4-7].The burning of rice husk in air results in the formation of RHA with content in SiO2 that varies from 87 to 97% depending on the burning conditions, the rice variety, the climate and the geographic area [8]. Some small amounts of inorganic impurities are always present in the ash along with unburned carbon. The unburned carbon can be removed from the ash by further heating treatments in high temperatures, but this usually leads to the crystallization of the amorphous silica to cristobalite and/or tridymite [9]. The crystallization of the contained silica of the ash is also occurred when the burning conditions of husk are uncontrolled [10]. This crystallization is a disadvantage towards the preparation of silicon based materials, because the silica ash is rendered inactive in its crystalline form [11]."

Jan 1, 2008

By G. S. Hanumanth

Sedimentation of particles during the liquid metal processing of particulate metal-matrix composites can affect the homogeneity, and thereby the properties, of the cast product. A novel electrical probe has been developed to measure the in-situ volume fraction of ceramic particles in molten metal baths. Using this probe, sedimentation rates for 90 pm silicon carbide particles dispersed in molten aluminum A356 alloy were measured over a wide range of particle volume fraction, 0.05 to 0.3. The sedimentation rate was found to depend strongly on particle volume fraction; the time to clarify a 0.15 m depth increased from approximately 60 to 500 seconds as the volume fraction increased from 0.05 to 0.3. Measured sedimentation rates agree well with the predictions of a sedimentation model based on one-dimensional, two-phase flow theory in which the inter-phase drag function is derived from the momentum equation, utilizing the Richardson-Zaki Equation for sedimentation in aqueous systems. The implications for solidification are discussed.

Jan 1, 1993

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By Laura Angeles, Martin Reyes, Ivan Reyes, Miguel Perez, Francisco Patiño, Mizraim Flores, Elia Palacios

Chemical and mineralogical characterization of a sulphide ore from the mining district of Zimapan, Hidalgo, Mexico, was performed in order to obtain accurate information on the composition of the ore to optimize the subsequent flotation process. A combination of techniques was used: Scanning Electron Microscopy (SEM) with Energy Dispersive Spectrometer (EDS), X-ray diffractometry (XRD), Inductively Coupled Plasma (ICP) and Fourier transform infrared spectroscopy (FTIR). The SEM mapping confirmed the presence of the elements: Ca, Si, Fe, K, S, Al, Zn, Mg and Mn. The XRD analysis suggests that the ore matrix is calcite; additional species found were wollastonite, johannsenite, and pyrite, among other impurities. The FTIR analysis performed for the aqua regia insoluble showed the presence of calcium oxide, copper oxide and silicon oxide. The results for the ICP analysis were:13.31% S, 2.55% Fe, 0.46% Zn, 0.03% Cu, 0.06% Pb, 0.07% Mn, 0.09% As, 0.01% Sb and 0.08 grton-1 Ag.

Mar 1, 2017

By Matti Leiponen

During the last few years Outokumpu Oy has put forth efforts to develop the material handling in the Pori tankhouse. The final objective is full automation including cell loading. The fully automated material handling provides high quality anodes and cathodes as well as equipment and handling systems capable of very accurate cell loading. The new machines and equipment for accurate cell loading and the methods to produce high quality anodes and starting sheets are described in this paper.

Jan 1, 1987

By James C. Sever

"With the advent of high energy costs and increasing concern for the environment leading to the incorporation the C02 life cycle as a criteria for the material used in a finished product, it is beneficial to analyze the plant and the process used in producing a raw material in order to identify practical, economic energy recovery opportunities. To this end a study was made of the proposed Nevada Clean Magnesium, Inc. Tami-Mosi reduction facility. Each source of waste heat is listed together with the assessment for potential co generation or direct recovery. The overall impact on energy requirement and C02 generation is provided.IntroductionHistorically metal reduction plants, large consumers of energy, do not recover waste heat. This occurred for many reasons:• Energy costs were low and the capital for a co-generation system could not be justified;• Waste heat sources contained entrained solids or liquids which would inhibit efficient energy recovery;• The exit temperature for the heat source was too low for efficient use by aaqueous Rankine cycle system.The business environment has now changed adding impetus to the recovery of energy previously discarded. Power costs have greatly increased. Global warming and the impact of carbon dioxide on the environment has become an issue which could impact the permitting of a plant. Technology improvements especially the development of a scaling environment waste heat boiler [l] and the development of the organic cycle Rankine cycle recovery system enable up to 70% energy recovery from ""low grade"" heat sources [2].With the inception of Nevada Clean Magnesium, Inc. 's (formerly Molycor Gold Corporation, Inc.)Northern Nevada Tami-Mosi project [3], an opportunity was presented to incorporate energy optimization from the initial design phase."

Jan 1, 2013