Search Documents

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By Heinz Böni, Christian Ludwig, Bernhard Steubing, Uca Silva

"Chile will soon have to find solutions for dealing with rapidly growing quantities of Waste Electrical and Electronic Equipment (WEEE) due to its strong economy and fast increase of internet and communications technology usage. To support this process, the state of the Chilean recycling infrastructure as well as government, industry and consumer efforts to deal with ewaste were analyzed. Current e-waste quantities were assessed and future flows were predicted using a material flow analysis model. In this model computer hardware was used as tracer equipment for WEEE. Best available numbers indicate that today’s formal recycling infrastructure receives less than 3% of the annual quantities of computer waste. This study represents the most comprehensive analysis regarding e-waste in Chile, identifying relevant streams of e-waste and providing a basis for authorities and producers of electronic goods in order to take the necessary actions to establish an adequate recycling system.IntroductionSince 1991, Chile has experienced a period of strong economic growth. It is amongst the countries with the fastest development in the sector of Information and Communication Technologies (ICT) in Latin America and the number of people with access to ICT has been growing rapidly. The high growth rates of the computer market over the last years are representative for the ICT sector with the consequence that the generated quantities of electronic waste are increasing rapidly [1, 2].Waste Electrical and Electronic Equipment (WEEE) or e-waste is “any appliance using an electric power supply that has reached its end-of-life” as defined by the OECD [3]. Even though the overall waste management in Chile has improved much over the last decade, the issue of ewaste was hardly addressed. Due to the value of the materials contained in computer waste - such as precious metals, basic metals as copper or plastics - it may be assumed that an important quantity is already being recovered. This usually takes place on the informal market under questionable conditions for human health and the environment [1, 2, 4]."

Jan 1, 2008

By B. M. Satish

The aim of the present work is to study the effect of annealing on the vibration damping capacity of high-chromium (16%) ferromagnetic steel. The alloys were prepared from raw materials of 99.9% purity melted in a high frequency induction furnace under high vacuum. The samples were heat-treated in vacuum at various temperatures (800 to 1200°C) for 1 hour followed by slow cooling (120°C/h). The inverted torsional pendulum method was used to evaluate the vibration damping capacity. The results indicated that the vibration damping capacity of the alloys is influenced by annealing and there exists a critical annealing temperature after 1000°C. The damping capacity increases quickly below the critical temperature since the magnetic domains move more easily.

Jan 1, 2009

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By Huimin Lu, Neale R. Neelameggham, Guangzhi Wu

In China’s Inner Mongolia Tuquan County, 1.4 billion tons of reserves of serpentine deposits were found. Because serpentine belongs to magnesium silicate, there is no good reducing agent to reduce magnesium. In the local there is also a large reserves of high-aluminum bituminous coal for thermal power, power plants each year produce a large number of high-aluminum fly ash. The aluminum-silicon alloys obtained from this high-aluminum fly ash as the raw material by carbothermal reduction method can reduce the magnesium from the serpentine. In this paper, first, the feasibility of producing aluminum-silicon alloys by carbothermal reduction of high-alumina fly ash was studied, the hypereutectic aluminum-silicon alloys were obtained; and then the investigation on aluminum-silicon alloy as a reducing agent to reduce of metal magnesium from serpentine was carried out. According to the previous investigation, the optimized technical process for the extraction of metal magnesium from serpentine was proposed.

Mar 1, 2018

By Wenjie Zhu

Chromite ore processing residue (COPR) is a hazardous waste containing high concentration of chromium. We describe here a pioneer trial of detoxification of COPR in column reactor with an indigenous chromate reducing bacterium Leucobacter sp. Ch1, which showed high chromate reducing ability at high pH. Under the optimum conditions, at 30°C and pH 10.0, pH of leachate decreased from 10.3 to 8.3, and Cr(VI) concentration in solution decreased to zero mg L-1, and 76.4% of Cr(VI) was removed from COPR samples. The leaching toxicity of detoxified residue was 1.1 mg L-1 that was lower than national standard of China.

Jan 1, 2008

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By K. Sanjay

Factorial optimisation technique has been used to develop regression equations at different time intervals for extraction of manganese from precipitated manganese oxide/hydroxide in sulphuric acid using charcoal as the reductant. The three parameters chosen for a 23 full factorial design were : acid concentration, amount of carbon and temperature. The regression equations were used to predict >> 90% extractions as well as kinetic data.

Jan 1, 1996

By Tian Sugui

By means of the long-term aging treated, creep properties measuring and microstructure observation, an investigation has been made into the microstructure and creep behavior of the casting and rolling GH4169 superalloy after long-term aged. Results show that, after the casting and rolling GH4169 superalloy treated by long-term aged, significant amount of " phase are dispersedly precipitated within the grains of the alloy, and some of the NbC, Cr7C3 carbide are distributed along the grain boundaries. In the range of the applied stresses and temperatures, the creep activation energies and stress exponents of LTA GH4169 alloy during steady state creep are calculated to be Q=541.1kJ/mol and n=16.2, respectively. During creep, the deformation mechanism of LTA GH4169 is thought to be the twinning and dislocation slipping within the twinning regions, and the damaging mode of the alloy is the intergranular fracture, and the non-smooth crystal surface is displayed in the fracture regions of the alloy. Thereinto, the carbides film formed along the grain boundaies has a few effect on the strength between the boundaries, which is a main reason of resulting in the alloy possessing a longer creep lifetimes.

Jan 1, 2009

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around I 100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By Jian Li, P. Liu, R. Zhang and J. Lo

In the past decades, focused ion beam (FIB) has evolved into a powerful microscope that provides capabilities that no other microscopes can offer. The combination of high-resolution imaging and stress-free ion beam cross sectioning provides valuable microstructure information both at the specimen surface and beneath. FIB techniques are also the preferred method to prepare site-specific transmission electron microscope (TEM) specimens. CanmetMATERIALS owns a world-class microscopy facility, where advanced microscopy work provides strong supports to research programs that cover a wide range of subject areas. This paper is aimed to provide a few practical examples of FIB applications in microstructure characterizations that include cross-sectioning and imaging, serial sectioning, and advanced TEM specimen preparation in materials research at CanmetMATERIALS.

Jan 1, 2015

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By A. Gibson

Most methods for the treatment of scrap printed circuit boards do not reclaim the components in working order as the boards are either fed to a copper smelter, to recover the valuable elements, or, simply landfilled. This work reports the dissolution of the solder in fluoroboric acid containing Ti4+ ions which was particularly selective for solder, allowing the components to be recovered. The solder was subsequently electrowon from the leachant. The boards were then shredded and the copper dissolved in ammonium sulfate and, then treated via solvent extraction to give an electrolyte suitable for electrowinning. The remainder of the metals were dissolved aqua regia, silver remained unattacked by the aqua regia, palladium precipitated as Pd(NH4)Cl6 in the presence of zinc and nickel, the gold was removed by solvent extraction and precipitated as nanoparticles. The aqua regia was then diluted and the zinc and nickel separated by solvent extraction.

Jan 1, 2009

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By M. R. Jolly, J. -C. Gebelin

"A number of different types of so-called ""filters"" are used in the metal casting industries to impart some cleaning effect and flow control on the liquid metal as it passes through them. The filters range from simple planar meshes through extruded channels to reticulated foam structures and they are manufactured from a range of material going from metals to glass or ceramics. It is most common that software packages used in the industry model the filters by a simple pressure drop associated with some area fraction and permeability parameters.Recent experimental work at the IRC in Birmingham [1] has shown that filters of the same type can behave very differently depending upon the casting process in which they are employed. Modelling filter geometries for a range of different casting processes has indicated that the flow of metal and heat losses through the filters are rather complex and should be considered when using filters in the casting processes. This paper will present a number of cases of different types of filters modelled and different processes and indicate some of the sensitivities of the processes to boundary conditions imposed by the process.IntroductionFilters are commonly used in the foundry industry. The real action of the filters on the liquid metal is not really understood. Some filters are claimed to have a chemical action on the liquid metal or to be able to clean the metal by stopping the impurities or oxides that will result in inclusions in the cast part. However, some recent experiment carried out at the University of Birmingham in investment casting and results available on sand casting [2] have shown that the action of filters may be different in these two processes. As the main difference between these two processes is the mould temperature, the hypothesis of a partial solidification of the metal in the filter occurring in the sand casting process during the primary stage of the filling has been advanced, whereas there is little or no solidification in investment casting. In order to verify this hypothesis, and to reach a better understanding of how filters work, a numerical investigation of the flow and heat transfer in filters in both sand and investment casting has started at the University of Birmingham, in the framework of the FOCAST project. The FOCAST project is an EPSRC project aimed to increase the understanding of the investment casting process. Another issue is the way the simulation packages predict the influence of the filters on the metal flow. The filters are most of the time modelled as porous obstacles characterised by a pressure drop calculated from porosity and some surface ratios or proprietary coefficients. This paper will present the preliminary results of this numerical investigation. First, the different models that have been used are presented, followed by the obtained results. A discussion of these results and their perspectives conclude the paper."

Jan 1, 2001

By Edgar E. Vidal

The deposition of ceramic materials onto substrates is of special interest in the development of surface related technologies. Research interest has been placed on using thermal plasma as the deposition method, specifically inductively coupled plasmas. Many different modifications to the same basic principle of deposition have been performed through out the materials research community. Such a technique may have many advantages over more conventional techniques, such as high deposition rates, high surface area coverage, clean energy source, no contamination from electrodes and operation near atmospheric pressures. Materials deposited vary from simple oxide systems like TiO2 to more complex structures like ternary oxides and nitrides. This paper reviews recent developments relative to the inductively coupled plasma deposition of thin films.

Jan 1, 2003

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017