Search Documents

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By John W. Graydon

Incineration is an attractive alternative to the disposal of MSW in landfill sites. However, the process of incineration generates fly ash which contains significant levels of leachable heavy metals - particularly cadmium, lead, and zinc - and it is essential to manage this fly ash in an environmentally sound manner. The compositions, phases, textures, morphologies and size of fly ash particles have been studied by light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how fly ash is formed during incineration, in understanding the leaching behavior of untreated fly ash if it is disposed of in a landfill and, most importantly, in guiding the development of the best treatment strategies for fly asti to mitigate its environmental impact.

Jan 1, 1992

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By Lionel Ryan

In 1996, the Dominican Republic operation of Falconbridge (Falcondo) developed a 5-year Process Control Plan in conjunction with the corporate Process Control group located in Sudbury, Ontario, Canada. This plan was further refined into an analysis of the areas of the highest potential economic return for the company with the reduction shaft furnace operation being the most promising. Historically, the reduction plant, which comprises 12 shaft furnaces, has been the bottleneck of ferronickel production. Since 1996 there has been a history of control development, and the current status is that all 12 furnaces are using advanced model-based multi- variable predictive control. The combination of advanced process control (APC), improved control system performance and improved process information management has resulted in an increased throughput of 6% per shaft furnace and a reduction in operating costs of 4.5 US cent/lb of Ni. This paper reviews some of the major milestones that have been achieved in this development Keywords: Advanced Process Control; Model Based Predictive Control; Connoisseur, Reduction Shatt Furnace; Nickel Laterite Ore; Ferronickel; MonitorMV

Jan 1, 2004

By A. Rojo, N. J. Ramirez, J. E. Salgado

"This work aims to characterize the plastics used in a handgrip located in the car interior body in order to improve its design process and be able to predict its behavior when the part is subjected to impact test involving human casualties.Through stress analyses at high speeds and a video camera set up (front and side view), the reduction of area of specimen was obtained from image analysis, allowing to get the stress-strain real curve of the material.Continuing the characterization process a set of impact test was developed, where standard lzod configurations were used in unnotched specimens. From these tests were gotten displacement curves and absorption energy estimations.The proposed testing procedure allowed the acquisition of force and displacement data through time at various strain rates which are indispensable for the characterization of dynamic events. Using a specimen with a special configuration has shown a more detailed dynamic behavior resulting into more accurate numerical analyses within the design process.IntroductionIn the design process, one of the many analyses which take place is the impact test of the designed part. Nowadays there are many software capable to do these kind of analysis and each industry use the one they think it is convenient for them, but also the selected software has mathematic models that help to find the solution and the simulation of the case of analysis. These are not the only considerations that a company has to take into account, other one is the type of information and data necessary to feed the software. For this study we are going to focus on the acquisition of these data.The mail reason of this work is that generally the supplier gives the card of the material with all the characteristics and information requested by the buyer, but all of that information is acquired by standard methods, but it is inconvenient when the materials are polymers."

Jan 1, 2011

By V. A. Luganov

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°C and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 550 DC with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilitc. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By Lincoln McCrabb

Correct measurement and interpretation of viscosity data is critical for design of any thickening and pumping process that involves a non Newtonian slurry. The nickel laterite pressure acid leach (PAL) process relies on producing a slurry of maximum achievable solids concentration. Small variations of 1-2% solids concentration can alter economics significantly. For the Ravensthorpe Nickel Project, a rheology protocol has been developed which optimizes the solids concentration across a range of ore types. The vane yield stress technique has been utilized to accurately quantify the flow of thickened slurry in the lower shear range. A yield stress of 100Pa has been used as a benchmark to determine the optimum solids concentration achievable utilizing deep cone thickening. Statistical analysis of the data shows critical rheology distinctions between ore type, particle size, lithology and geochemistry. Linear and power law models have been applied to rheology flow curves to reconcile the material transport properties with the anticipated thickener underflow solids concentration. Keywords: Vane Yield Stress, Thickening, Rheograms

Jan 1, 2004

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004

By John Norton

"This presentation will cover the physical properties of waste heat recovery. It is a two part presentation. The first deals with actually recovering the heat with new state of the art heat exchangers and applying that heat to the furnace combustion and the second part will cover what other processes you can enhance with this ""free"" heat. It will also talk about converting it to steam, hot air or electricity to be used or sold back to the utility company. The economics of various schemes will be reviewed. A brief discussion on State and Federal grants and subsidies will be presented.IntroductionThere are large quantities of wasted heat in the usual aluminum melting process. And, there are several techniques for reducing and/or using some of that wasted heat as you have seen. Any technique that can make use of wasted heat is a form of recovery. This can range from simply preheating aluminum billets prior to melting, to more complicated processes like air-to-air heat exchangers using the boiling and condensing characteristics of special fluids in “heat pipes.” The objective of this type energy recovery process is to move the wasted heat from the hot and dirty exhaust gas stream into some useful process.Waste Heat Recovery in the Aluminum Melting Furnace.There are considerations, of course:1) What might the value be of the recovered energy?2) Can the recovered energy be used within the process? Within the plant? Or by theneighbors?3) What is the capital cost?4) Is the recovery process complicated?5) Will it take additional staff?6) Will it cause additional downtime on the melting line?7) Will the operations staff need to be licensed?Ideally, the process will be simple and inexpensive, the recovered energy will be very valuable, and the whole effort will cause little distraction to the aluminum melting process itself. These would be ideal."

Jan 1, 2011

By Cailing Zhen, Jian Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Guixiang Huang

The grate-kiln process has been widely applied for oxide pellet production with the quick development of steel industry in China, but ring formation takes place which adversely affects the productivity and properties of fired pellets. Rotary kiln at high temperature seems a black box, and ring formation is difficult to measure directly by current technology. It’s of great importance to monitor ring formation during firing of pellets. Therefore, a method for estimating the thickness of ring formation in rotary kilns was studied, based on working out theoretically the relationship between ring thickness and the outside surface of the kiln, according to steady-state heat transfer across a cylinder, which provides a soft-sensing technique for ring formation at high temperature, and achieves stable pellet production .

Jan 1, 2015

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectic Sn-Pb) and two types of nickel- based UBMs, electroless Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed. The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples of Sn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By Guojun Qi

This work relates to wafer bumping technologies for flip chip packaging applications in the electronics industry. Nickel and its alloys are alternative under bump metallization (UBM) materials because of their slower reaction rates with Sn-based solder as compared to Cu-based UBMs. In this study, we compared the morphologies of the intermetallic compounds (IMC) formed between Sn-bearing solders (Sn3.5Ag and eutectie Sn-Pb) and two types of nickel- based UBMs, electro less Ni-P (EN) and sputtered nickel. Both chunky-type and needle-type of intermetallics were observed between the EN UBM and the solders. In the case &apos;of sputtered Ni UBM, there is only a layer of scallop-type intermetallics formed, The morphology change and growth kinetics of the IMC in thermal aging process were analysed. Kirkendall voids were noticed from samples ofSn3.5Ag solder vs Ni-P UBM that have undergone prolonged thermal aging at high temperature.

Jan 1, 2003

By Yoshihiko Maeda

It is said that the 21st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980&apos;h due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologis and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By Ernie M. Crist, Laurentiu Nastac, Frank Spadafora

"This paper describes the modeling techniques and the experimental and computer results for two casting processes that are under development and optimization. These processes are described as follows:1) Electromagnetic stirring (EMS) during casting of Ti-6Al-4V round ingots using the plasma arc cold hearth melting (PAM) process: The purpose of EMS is to establish a singlemelt PAM process capable of consistently producing as-cast ingots without helium porosity and also having no need for surface conditioning prior to secondary processing.. The modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure.2) Casting of Ti-6Al-4V slabs using the single-melt PAM process: The purpose of slab casting is to improve yield by eliminating an intermediate blooming step for converting round ingots to slabs. The modeling approach is based on the numerical solution of fluid flow and heat transfer equations. The effects of pouring and mold temperatures on the pool and temperature profiles were studied. Also, the torch effects (such as the torch standoff and its traversing path) on the pool and temperature profiles were investigated and the best-case scenario was used in the experiments. Evaluation results at RMI Titanium Company showed that the plates made from the slabs met the mechanical properties and microstructure requirements.Acknowledgment. This work was conducted by the National Center for Excellence in Metalworking Technology (NCEMT) operated by Concurrent Technologies Corporation (CTC) under contract No. N00014-00-C-0544 to the US. Navy as part of the US. Navy Manufacturing Technology Program. Dr. K. b. Yu from RMI and my colleagues from CTC are acknowledged for their comments on this work."

Jan 1, 2004

By Rodney Hundermark

At Anglo American Platinum’s Polokwane Smelter, radar instruments are being used to provide continuous measurement of the concentrate feed level in the six-in-line electric furnace used for smelting of nickel-copper concentrates containing platinum group metals (PGMs). The radar instruments are installed directly on the furnace roof, and a mechanical system has been designed to protect them from radiation and elevated freeboard temperatures and pressures. Signal validation criteria have been implemented to ensure that proper level measurements are being used by the PLC system. The feedback from the radars has provided an improved understanding of the furnace behaviour with respect to concentrate feed level control, individual feeding events, global feed rates, feed distribution and bath disturbances. In combination with a dynamic mass balance for continuous calculation of liquid level in the furnace, the radar measurements have enabled more precise feedback control of the concentrate blacktop depth. In turn this has yielded improvements in furnace stability.

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z&apos; is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z&apos; (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

By Pedro Morales

At present the Codelco´s smelter & refinery business have growing complexities, concentrates with lower copper grades, higher impurities contents, and environmental restrictions which have lead to refocus the Codelco business, not only by considering the isolated developments for each of the Codelco´s Smelt & Ref complexes, but also as an integrated corporative complex scheme which improve the economy of scale, optimize the synergies, and include new technologies for higher productivity and lower operational costs. Accordingly, for the 2008-2012 period, Codelco have prepared a Development Plan integrated to the smelters and refineries business units that improve its single potentialities of and include the advances for the Teniente Converter [1] and Continuous Converting [2] Technologies, and also include the concept of uncoupling the smelting process from the converting process allowing a higher operational flexibility, and a better control of its contaminants. Thus, processing the white metal generated in the Teniente Converter unit of the smelter A into the smelter B has comparative advantages. These changes in the business concept allow an overall increment of the smelting capacity by processing only white metal as a final product through a very marginal investment in this way the total or partial conversion of the white metal into blister copper is eliminated allowing to use the available gas capture-treating capacity, and available acid plants for increase smelting capacity as well.

Jan 1, 2006