Search Documents

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

By KNona Liddell

Many metal recovery processes Involve heterogeneous reactions In porous media accompanied by fluid flow and mass transfer. Modeling such systems Is difficult because of the number of rate processes Involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide, an attractive alternative to models based on transport ,mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.

Jan 1, 1996

By Laurentiu Nastac

"This paper describes the development and validation of a comprehensive multiscale modeling approach capable of predicting at the mesoscopic scale level the ingot solidification structure and solidification-related defects commonly occurring during the vacuum arc remelting (VAR) process. The approach consists of a coupling between a fully transient macroscopic code and a mesoscopic solidification structure code. The predictions from the multiscale model, including grain morphology and size, primary and secondary dendrite arm spacings, Laves and NbC phases, tendency for freckling and columnar-to-equiaxed transition, were validated against experimental measurements for a 20-inch diameter VAR alloy 718 ingots. The validated model was then used to investigate the effects of melting rate and ingot diameter on the solidification structure of VAR processed 718 ingots.IntroductionThe objective of this work was to develop a fully transient multiscale modeling approach to get an insight into the effect of processing parameters on the cast micro- and macro-structure during VAR processing. The developed model assists in achieving better control of the ingot solidification structure and to determine trends in the macrosegregation in these ingots. Another objective of this work was to analyze the transient effects of production rate and ingot size on the resultant ingot microstructures. This objective was met by first understanding the effects of the full range of processing parameters typically used in the VAR process. Processing parameters such as power input and heat extraction rate significantly influence the ingot liquid pool size and shape as well as the ingot structure, which in turn will greatly impacts the final ingot quality."

Jan 1, 2012

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By S. D. Prosser

The earliest record of slag in the world was the discovery of the remains of a copper blast furnace in Southern Israel, which has been carbon dated at 3500BC, nearly 6,000 years ago. Slag in Australia is a much more recent phenonenum with the first iron blast furnace commencing operations in 1848. The early days of metal smelting in Australia were marked with many company failures due to a variety of reasons. This paper traces the progress of metal and slag production from those early days up to the present times

Jan 1, 1994

By B. Sereda

As it is known the creation and development of new titanic alloys has been problematic up to now. They can be used in aircraft and vehicle construction, shipbuilding and as materials for keeping static loadings in high-temperature environments. In this work the synthesis of various titan aluminides is investigated. Mathematical model of structurization process was done. On the base of retrieved model the mechanisms of structurization in systems Ti + Al and Ti + 3Al was determined. Experimental researches were done at two different modes: burning and thermal spontaneous ignition. The method of retrieving compacted products combusted in SHS conditions (SHS-compacting) was used to gain these intermetallic compounds. The physical and thermal characteristics of technological process and their influence on structurization, homogeneity of structure and porosity of titan aluminides have been simulated and researched. It is established that the SHS-compactizing technology is fully capable of supervising the process of structurizations with the whole complex of advantages and can be applied for receiving qualitative titan aluminides with the set of chemical-physical properties.

Jan 1, 2010

By Mario Sanchez, Jose Palacios, Fernando Parada

Carbon steels have less than 0.02% copper and have low atmospheric corrosion resistance. The addition of at least 0.20 wt% Cu improves this property. Also, 0.8 wt% Cu in steel shows a hardening potential for developing high strength corrosion resistant steels. Copper slags containing 42–45% of iron, silica and minor amounts of copper were used for producing Fe–Cu alloys by reducing the oxides contained in the slag to obtain a Fe-0.84 wt% Cu alloy, which could be suitable as feeding material to manufacture a corrosion resistance steel, and also would be an alternative for minimizing the copper industry ’s environmental impact, and to introduce the application of the Circular Economy concept to the natural resources exploitation, especially in countries where their economy is strongly based in mining and metallurgical extraction.

Mar 1, 2018

By A. Martins, L. Goulart, E. Araujo, R. Batista, A. Costa e Silva

Steel cleanness is of great importance to the performance of almost all steel products. From very clean steel for bearings to long products used in civil construction, processing variables – in special those in steelmaking operations- must be properly balanced to achieve adequate cleanness for the desired performance. With the present complexity of steels as alloy systems, it is not efficient nor appropriate to develop these processes on empirical basis alone. Computational thermodynamics can greatly improve process development to achieve the desired cleanness level at reasonable costs. In this work, examples of these calculations and their applications to real steel processing are presented and discussed. The advantages, limitations and areas in which improvement in these calculations is desired are highlighted and discussed.

Jan 1, 2015

By R. Cameron

The growing use and acceptance of electric vehicles (EV), as evidenced by the record sales of over 750 thousand vehicles in 2016 and a current global EV stock of 2 million vehicles, is putting pressure on sourcing raw materials such as cobalt, and to a lesser extent, nickel. Global supply is poorly diversified, with 50– 60% of global cobalt production sourced solely from the Democratic Republic of Congo (DRC). One potential source for cobalt and nickel are low-grade nickeliferous pyrrhotite tailings, of which 50–100 million tonnes are present in the Sudbury area alone. This paper presents the extraction of cobalt and nickel from this material using a combination of flotation and bioleaching technologies. The findings of a high-level techno-economic analysis of the proposed processing flowsheet are presented.

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By Hongmin Zhu, Kai Huang, Shuqiang Jiao

"Garlic peel was used as the raw material to synthesize the biosorbent for the selective recovery of precious metals from the acid chloride solution. Garlic peel is rich in carboxyl-, amino- and thiol-groups, has the potential of exhibiting high affinity to Au(III) when appropriate chemical modification process was employed. Here in the present study, the biosorbent was prepared by cross-linking garlic peel particles with concentrated sulfuric acid. Adsorption tests for mixing different metal ions such as Au(III), Fe(III), Cu(II), Ni(II) and Zn(II) from various concentrations of hydrochloric acid media indicated that Au(III) was selectively adsorbed on the cross-linked garlic peel gel over the other coexisting base metal ions investigated. The crosslinking mechanism and selective adsorption of Au(III) were also investigated briefly.IntroductionPrecious metals are quite popularly applied in the modern industries such as jewelry, electronics and electrical devices, catalysts in chemical industry, etc. While their high values, limited deposit and quite large demand in industry makes its recovery from the industrial wastes, typically e-wastes, quite necessary. Actually, many techniques have been developed to recycle and recover the precious metals from various industrial wastes effectively in last decades, but the cleaning and ecofriendly processes are still seriously scarce [1]. Taking into account of the typical recovery processes using cyanide lixiviant in the alkaline media, or aqua regia, followed by the further recovery process using activated carbon adsorption or cementation with zinc, iron or aluminum plate or powder, though they both are quite effective recovery processes, if considering the special requirements on safety and ecofriendliness for the modern hydrometallurgical processes, various improved or novel extraction processes are greatly demanded [2]. Recently, the biosorption technology applied to the recover precious metals in the hydrometallurgical process has become a concern [3,4]. Inoue’s research group made great progress in the recovery of precious metals such as gold, palladium and platinum from the e-wastes such as spent mobile phone by using biosorption from the hydrochloric acid media [5,6]. This new hydrometallurgical process exhibits the prominent advantages of being cost-effective for its short process, easy operation and near-zero emission. In the above recycling process for e-wastes treatment, the preparation of biosorbents is the key and backbone of the whole recovery process. For this purpose, they developed a series of suitable sorbents for precious metals recovery by using the tanning-based or cellulose-based biomass such as persimmon peel, grape peel, orange juicing residue, waste cotton, waste paper through the crosslinking process with concentrated sulfuric acid and relative chemical modification processes [7-10]. In the present study, we also applied this technique to prepare the biosorbent of precious metal uptaking by using garlic peels as the raw materials, and investigated the adsorption properties of such-obtained gel in the hydrochloric acid media."

Jan 1, 2012

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Al2O3 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and Po2 in a range between 2.5x 10-and 10.1 Pa by using CO-CO2-SO2 gas mixtures. The content of nickel in the slag at Po, of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4, I mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 02 mass%, respectively. ft was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy, The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-Al2O3 based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial pressure.

Jan 1, 2003

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Ah03 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and pO;, in a range between 2.5x,IO,2 and 10.1 Pa by using CO-C02-S0Z gas mixtures. The content of nickel in the slag at POz of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4.1 mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 0.2 mass%, respectively. It was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy. The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-AI20) based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial' pressure.

Jan 1, 2003

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By Jong-Shin Chang

The Onsan smelter has tried to do various activities to decrease operation costs. With several expansion projects, the Onsan smelter has aimed at not only a quantitative growth but also qualitative growth through efforts improving operations equipment and processes. Activities to reduce operation costs have been one of those efforts. In particular, the energy cost of operation has been a main target for reduction. The activities to save energy have been carried out in two ways. One is to recover and utilize waste heat as much as possible and another is to replace existing equipment and processes with more energy-efficient ones. This paper reviews recent improvements and future plans for energy saving activities at the Onsan smelter.

Jan 1, 2006

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By C. Carreno, A. D. Gonzalez Escarcega, M. A. Neri, A. Martinez –Villafane, O. Cobarrubias-Alvarado

"Waspaloy is a superalloy used to manufacture some aeronautical parts subjected to high temperatures and stresses. During thermo-mechanical processing cracks are generated, causing some parts to be rejected. In order to determine the causes of these cracks, this alloy was characterized using techniques such as chemical analysis, optical microscopy, scanning electron microscopy, and EDX analysis. Heterogeneous grain sizes in the microstructure cause a non-uniform strain distribution in these parts, creating cracks in zones with different grain sizes.IntroductionNickel-base superalloys are important materials for high-temperature service applications. The manufacture of components from these materials is typically based on solidification or powder-metallurgy processes [1]. Solidification techniques comprise either the direct casting of parts or the casting of ingots which subsequently undergo a series of thermo-mechanical-processing steps to refine the microstructure. During solidification, microsegregation is usually unavoidable. The primary solidification product is a disordered nickel solid solution with an fee crystal structure (?). In many alloys, the material which solidifies last is a mixture of ã and an ordered fee phase (? '). In prototypical nickel-base superalloys, the ?'-phase is Ni3(Al,Ti) [2-3].Waspaloy is a superalloy that is used in demanding high-temperature environments in which good creep and fatigue resistance are required. One of the most common applications of Waspaloy is for turbine engine rings. To ensure the required mechanical properties, the rings are usually forged and heat treated (Figure 1). Two distinct types of microstructures are usually found to be attractive for such applications: a) A microstructure with a grain size of ASTM 10 to 14 for tensile strength, ductility, and resistance to crack nucleation in low-cycle fatigue; or b) A microstructure with a grain size of ASTM 4 to 8 required for creep strength and resistance to crack propagation [4]. Because it is impossible to refine the grain size through heat treatment, a skillfully designed forging process is crucial for the control of the grain size and, hence the properties of the forged ring [5-6]."

Jan 1, 2012

By C. M. Dentan

Conventional testing of crude kaolin ores emphasizes physical properties as they relate to end uses of kaolin products. This approach to evaluating crude ores does not reveal the basis of behavioral differences between typical coarse and fine kaolins from central Georgia. Optical and scanning electron microscopy in combination with XEDS have been employed to characterize both coarse Cretaceous and fine Tertiary kaolin in order to shed light on the reasons for the gross differences in their properties. Routine evaluation of various parameters was also carried out. Bulk densities were 1.48 g cc-l for the coarse clays and 1.53 g cc-1 for the fine clays. Surface areas were 15 m2 9-1 and 25 m2 9-1, respectively. Brookfield viscosities were low for the coarse clays at 70% solids, and high for the fine clays. The situation was reversed for Hercules viscosities. Sixty percent of the coarse clays had particles of less than 2 um and the fine clays had 90% less than 2 cm. Micrographs of thin sections prepared from blue-dyed epoxy-impregnated crude ores and of SEM fabric samples demonstrated vivid differences in texture. Cretaceous kaolins appeared to be completely recrystallized residual products of former aluminous sediments, while Tertiary kaolins retained their essentially sedimentary character. Differentiation of the coarse and fine kaolins is rapidly accomplished by both optical and scanning electron microscopy, and should be considered a valuable analytical technique in evaluating kaolin ores.

Jan 1, 1981