Search Documents

By P. Lussiez

Precipitates consisting of amorphous ferrihydrite and crystalline goethite have been prepared by aging hydrolyzed Fe (III) solutions at room temperature. The precipitates have been characterized by x-ray diffraction and differential thermal analysis. The amorphous ferrihydrite transforms to goethite with time. The ferrihydrite to goethite transformation is affected by the presence of small amounts of copper or nickel coprecipitated with the iron. .The addition of copper decreases the amount of goethite at a given aging time and increases the amount of coprecipitate which is initially dissolved in sulfuric acid, but it does not seem to affect the dissolution of the crystalline part'. It is proposed that adsorption of copper hydroxo species on goethite nuclei delays the ferrihydrite to goethite transformation. The effect of nickel is less dramatic than that of copper. Apparently a portion of the added nickel is adsorbed on the goethite crystallite surface rather than incorporated into the goethite lattice.

Jan 1, 1981

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

By Liu Chunpeng

The new technological process developed is by means of thermal plasma arc smelting to obtain high grade Ni matte directly from Ni-Cu concentrates containing 6-7% nickel and 3-8% sulfur. In comparising with conventional smelting and converting processes the plasma arc smelting process has many advantages over conventional processes, such as lower energy consumption, lower capital investment and free from SO, pollution by transforming the sulfides into elemental sulfur with microwave irradiation under controlled oxygen potential, moreover, the process is simple and easily controlled due to less magnetite troubles in the operation. Therefore, this new technological process can be used as an alternative way to conventional process for Ni-Cu concentrate smelting. The main economical technical index is summarized in Tabal 1. Table 1 Main Ecnomic-technical Index

Jan 1, 1993

By Larry Southwick

In the early 1940's, the Caron ammonia ? ammonia carbonate leach process was used to produce nickel from Mayari ores at the Nicaro plant in Oriente Province, Cuba. While plant operation was generally successful, it was not broadly economical and was shut down. The plant was later restarted in the 1950's and a number of investigations initiated to resolve the more serious operational and performance issues. Processing steps studied included iron reduction (chemistry ? nickel and iron, reductant, equipment), ore variability (homogeneity and consistency of mineral concentrations, serpentine vs. laterite), leach solution strength, nickel recovery (temperature ? reduction and leaching, reoxidation) and a variety of other topics. These studies and their findings will be discussed. Caron himself obtained good results on these ores in the laboratory. They could not be duplicated in the field, the reasons for which will be reviewed. (Note: the ore looked like garden dirt; charcoal made from palm trees was one of the reductants attempted; and ammonia was the leach solution. Mixing the three, so to speak, was to yield nickel.)

Jan 1, 2006

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012

By Tobias Dubberstein, Hans-Peter Heller

The viscosity of Fe-Cr-Mn-Ni TRIP/TWIP (Transformation Induced Plasticity, Twinning Induced Plasticity) steel with varied nickel content is investigated using a vibrating finger viscometer. The viscosity of the melt is calculated from the change in power input in the field coil by an immersed finger into the liquid steel to maintain a constant peak-to-peak amplitude of the sine wave of oscillator compared to the idle state. Nickel content in steel is varied from 3 wt% to 9 wt%. The dynamic viscosity (η) at 1600 °C for 3 wt% Ni is 3.73±0.14 mPas, for 6 wt% Ni 3.50±0.03 mPas, and for 9 wt% Ni 3.93±0.09 mPas. There is a kink from low to high nickel content in viscosity values of Fe-Cr-Mn-Ni alloys. This phenomenon can be explained by a change in coordination number in the melt, as reported for Fe-Ni binary system in literature. The availability of viscosity data delivers relevant input to model free fall atomization processes of FeCrMnNi alloys.

Jan 1, 2015

By Catherine Cai

A granular sorbent, prepared by gel-coating polyethyleneimine (PEI) on high surface area silica followed by crosslinking with a low-molecular weight diepoxide, has significantly higher uranium capacity, greater salt tolerance, and faster kinetics than the commercial resin Dowex 21K. Though having lower U(VI)/Fe(III) selectivity than Dowex 21K, the gel-coated PEI affords much higher sorptions of both U(VI) and Fe(III) and also their separation by selective stripping with acid.

Jan 1, 1999

By Regina Maria Pinheiro

This work has for objectives to characterize a waste generated in the form of sludge during the treatment of the effluent of a paper making industry and to evaluate the effect of its incorporation in the amount of 10 wt.% on the properties and microstructure of a clayey body used for brick production. For the characterization of the waste the following techniques were used: X-ray diffraction, X-ray fluorescence, differential thermal analysis and termogravimetric analysis. Incorporated bricks were produced in industrial scale before firing at 750°C in a Modified Caieira type furnace. The physical and mechanical properties evaluated were water absorption and compression strength. The microstructure of the fired ceramic was evaluated by optical microscopy. The environmental evaluation was made by solution test and atmospheric emission by monitoring the release of SO2, NOx and particulate material. The results showed that, in agreement with the characteristics of the waste, its recycling into red ceramic can contribute to decrease the consumption of fuel during the firing stage. The properties of the fired ceramic attend the norms. With respect to the environmental aspect, the incorporation of the waste did not impact the environment.

Jan 1, 2009

By Ann M. Hagni

Flash reduction of zinc oxides is an alternative, environmentally safe method to leaching and electrowinning for zinc recovery. Zinc and lead are volatilized in a flash reactor, a non-hazardous residue is generated, and the fuel source is inexpensive coal in the flash reduction process. Results from experimental laboratory tests yielded low zinc recovery for this process. Mineralogical and textural characterization of the residues from the flash reduction tests for different feed materials and temperatures were conducted to determine the cause for the low zinc recovery. Reflected light microscopy, cathodoluminescence microscopy, scanning electron microscopy-energy dispersive spectroscopy, and X-ray diffraction were utilized in this applied mineralogical research. The original zinc calcine is composed primarily of fine-grained, iron-bearing zincite particles, 25-40 um in diameter, in a porous texture. Pellets processed at 1150°C were found to produce reaction rims of franklinite-magnetite-jacobsite solid solution that are 125-200 um thick and surround cores of unreacted iron-bearing zincite in a Zn-Fe-Si-Ca glass matrix. The reaction rims have subsequently oxidized to form an outer 10 ~m thick rim of hematite. Slags from calcines processed at 1275°C are primarily triangular particles with porous centers, cenospheres, and spheres of iron-bearing zincite, in addition to rectangular particles composed of non-porous franklinite-magnetite solid solution cores with iron-bearing zincite rims. Slag particles from calcine processed at 1200°C are predominantly 100-250 ~m triangular-shaped, spheres, and cenospheres containing fine-grained franklinite and franklinite-magnetite solid solution in an iron-bearing zincite matrix. Slag from calcine processed at 1300°C are also predominantly 1 00-250 um triangular-shaped, spheres, and cenospheres but contain coarser-grained iron-bearing zincite. The zincite in the penets and the slags typically contain 10-20% iron. Based upon these mineralogical observations, it is concluded that the significant amounts of iron in the zincite prevent volatilization of the zinc in the flash reduction process.

Jan 1, 1995

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By S. Redik, C. Wenzl, D. Gregurek, A. Spanring

Zinc is a component of many input materials used in various pyrometallurgical processes, for example primary lead and zinc production from Pb/Zn ores and recycling processes dealing with zinc-containing residues (e.g., copper recycling, WAELZ process). Hence, zinc and its compounds are present in the respective metallurgical vessels and interact with the refractory lining. In the present work the zinc attack on the refractories out of various primary and secondary furnaces is briefly introduced and discussed. At the prevailing processing temperatures in the metallurgical vessels, zinc oxide is highly corrosive for the brick components. The knowledge of the wear behavior is based not only on a detailed chemical and mineralogical characterization carried out on provided post mortem samples, but also on FactSage calculations. This together with results obtained by practical testing in the RHI pilot plant represents an important prerequisite for product development and brick selection for the individual customer application.

Jan 1, 2016

By G. G. Krishna Murthy

Interactions of wustite and hematite pellets with Fe-C melts were investigated experimentally by examining the effect of pellet size and bath temperature on the reduction rates of the pellets. Experiments were carried out in the temperature range 1473-1923 K. A flash X-ray equipment was used to obtain images of the melt surface during its reaction with an oxide pellet. The reduction rates were calculated using experimentally estimated time for complete reaction of a pellet, tR. The value of tR was determined employing gas mass flow rate, or pressure rise in the sealed furnace, versus time traces. The value of tR was the same for both wustite and hematite pellets of equal weight at or above 1723 K and it decreased with increasing melt temperature. But the reduction rate was substantially lower at temperatures below 1651 K, the melting point of wustite. The rates were defined as the rate of moles of oxygen removed from the pellet per unit area of bath free surface and it was found that the bath surface area affects the reduction rates. It was established that the overall reaction followed nth-order rate kinetics with the values of n falling between 0.3 and 0.4 for temperatures above the melting point of wustite. The apparent activation energy determined using the apparent rate constants obtained from the experimental data was 76.2 + 27.7 kJ/mol-O.

Jan 1, 1992

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides (MA) can be incorporated for use as a transmutation fuel. This study involves characterization of precursor powders and pellets to be inserted into the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U80Pu20)O1.98, and two compositions of MA-MOX with oxygen to metal ratios (O/M) of (U75Pu20Am3Np2)O1.98 and (U75Pu20Am3Np2)O1.95. The precursor powders, which consisted of, highly enriched uranium oxide, HEUO2, depleted uranium oxide, DUO2, neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a field emission gun scanning electron microscope (FEG-SEM) for particle morphology, size, and size distribution prior to pellet production.IntroductionThe Global Nuclear Energy Partnership (GNEP) was created in order for “fuel-cycle supplier” nations to provide assured supplies of nuclear fuel to “fuel-cycle customer” nations. The customer nations would utilize the fuel for electricity generation and subsequently return it to the supplier nation after it is spent. This spent fuel would then be reprocessed by the supplier nation in order to recycle the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials would also be strictly controlled through the International Atomic Energy Agency. One of the thrust areas for the GNEP program is the development of these actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3]."

Jan 1, 2008

By Jr. Brown, A. Calderara, A. L. Antozzi

"The result of extensive research into fundamental mixed metal oxide catalyst morphology has produced a next generation all titanium Dimensionally Stable Anode (DSA ®). This new DSA ® anode, patent pending, is tailored for electrowinning of non-ferrous metals (copper, nickel, cobalt, zinc) by means of this new coating technology.These DSA ® anodes are characterized by a hanger bar with vertical distributor bars, having primary titanium mesh attached by weldments. The active mesh is provided with noble-metal electrocatalytic coatings, consisting of iridium and/or ruthenium oxides, obtained by thermal decomposition of precursor solutions applied to the titanium substrates. The catalytic activity of state-of-the-art DSA ® anodes is increased by controlling the crystallite size of the noble-metals without decreasing the decomposition temperature. It is known that below a certain value (typically 400°C) the stability of these oxides, and associated lifetime, is seriously compromised. A highly active DSA ® anode, consisting of a quasi-amorphous phase, is obtained at high temperature (above 450°C), therefore not compromising lifetime performance. Through optimization of these design parameters, the manufacture of these novel anodes was identified.DSA ® anode performance advantages include: lead-free ' green' all titanium anodes, true leadfree cathode quality, energy savings of 0.3 to 0.55 V can be realized depending on the EW application when compared to industry standard lead-alloy anodes, eliminate need for cobalt sulphate addition required for lead anodes, sustainability designed into long-life recoatable anode structures, increase plant cathode output through increased current density operations, improve plant on-stream production, no sludge generated or removed, and improve current distribution producing smooth high efficiency cathode.Introduction of ProductThere are many factors to consider when engineering a high performance DSA ® electrowinning anode. Half of the anode's performance is derived from the physical attributes of the electrocatalyst and methods employed when applying this catalyst to the titanium anode structure. The other half of the performance benefits relate to the proper structural design of the anode. In this paper, we will highlight the anode development program in which De Nora has invested to provide the Electrowinning marketplace with a high performance anode product."

Jan 1, 2012

By Shan He, Qiang Wang, Xuling Chen, Min Gan, Lishun Yuan, Xiaohui Fan

"The sintering properties of vanadium-titanium magnetite concentrate(VTC) was studied in this paper. Through the optimizing the sintering process of VTC, the suitable granulation moisture and coke proportion were determined. The sintering velocity decreased from 23.05 mm/min to 18.22 mm/min. With the increase of VTC proportion from 0 to 46%, the specific productivity and tumbler index were respectively decreased from 1.55 t/(m2·h) to 1.21 t/(m2·h), and 62.93% to 57.73%. The temperature of liquid phase formations of mixtures increased, the amount of liquid lowered, and the content and sharp of sintering mineral gradually changed with the increase of VTC ,these lead that sinter quality became worse.IntroductionIn recent years, the steel industry of China is developing rapidly. And the steel production was 627 million tons in 2010. At present, the resources of vanadium-titanium magnetite concentrate(VTC) was about 14.4% of the total national iron reserves of China[1]. VTC has been used as sintering material by Magang, Chenggang and Pangang. The amount of VTC in Pangang is maximum. However, there exist many problems in VTC sintering, which involve in high specific productivity, bad sintering tumbler strength and high energy consumption[2~5]. That’s why the proportion of VTC is limited in sintering.The high quality of iron ore resources is worse in China. Therefore, it’s necessary to study the properties of VTC sintering, and to find out the reason how the VTC ratio affect the sinter performance. Purpose and significance of the research is to get high-quality sinter with the proportion of VTC greatly raised."

Jan 1, 2012

By M. Oliazadeh

Spodumene [LiAl(Si2O6)] is the most common and desirable economic lithium-bearing mineral due to its high lithium content. In Canada, there are several spodumene deposits at the development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and increasing use of electric vehicles. Spodumene processing can be conducted using Dense Media Separation (DMS), flotation or combination of both. If spodumene liberation is sufficient at coarse particle sizes, DMS can be used for primary lithium concentrate production and silicate gangue minerals rejection. If liberation is not sufficient, flotation is then the main processing route for spodumene concentration. Even in cases where DMS is a viable beneficiation option, flotation may still be required to process the DMS middlings and/or the undersize fraction which is outside the particle size range for DMS. Considering flotation as a technique for spodumene beneficiation, there are several alternatives including the use of mechanical flotation cells, column flotation cells, coarse particle flotation cells, and/or Staged Flotation Reactors (SFR), either alone or in combination. Ore sorting can be incorporated at the start of the spodumene flowsheet to remove gangue minerals, particularly amphibole and pyroxene in the early stages. The main objective of flowsheet development for hard rock lithium deposits is to evaluate the ability of these options to produce a spodumene concentrate with a concentrate grade above 6% Li2O, lithium recovery of above 80%, and with the minimum operating and capital cost. This paper aims to describe the various processing options available for the beneficiation of spodumene from hard rock deposits and compare the associated operating and capital costs for each.

By W. Dresler

Design details of a 100 kVA DC electric-arc reduction furnace are described. The furnace is equipped with a 610 mm (24 inch) diameter graphite crucible hearth. A 76 mm (3 inch) diameter top graphite electrode is used as a cathode. The current passes through the bottom of the crucible and is carried to a bottom plate (the anode) by conductive magnesia carbon bricks. The furnace can be operated up to a maximum of 120 V, 1800 A, and presently 100 kW. The start-up operating experiences and metallurgical results of one reduction test with a Montana chromite containing 38% Cr2O3 are discussed.

Jan 1, 1994

By C. A. Natalie

Prediction of average residence times for different particle size intervals during sulfide roasting was investigated. Calculations were done to predict average residence times using a model which employs empirical correlations for elutriation constants. Experimental average residence times were determined using a continuous., six inch diameter,. fluid bed roaster and compared with calculated residence time values. Comparison of calculated and experimental data showed that geometry effects may have .been significant when attempting to apply elutriation data to this roaster.

Jan 1, 1985