Search Documents

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By A. V. Tarasov

In order to improve the efficiency of hydrometallurgical processing of pyrrhotite concentrates, an integrated set of research has been carried out to investigate the use of sulfur dioxide in individual unit operations and as a leaching agent in the autoclave process as a substitute for oxygen. Treating iron-containing raw materials for production of nonferrous metals are based on the selective reaction of SO2 with iron sulfides and oxides. Iron is dissolved as sulfate, which can be treated in a separate circuit to produce iron-containing pigments or it can be disposed of after neutralization. Nonferrous and precious metals contained in pyrrhotite concentrate do not react with sulfur dioxide and remain virtually completely in the solid phase, i.e. high-grade sulfide concentrate to be treated by hydro- or pyrometallurgical methods. Elemental sulfur formed in the process of leaching is separated from the pulp in granulated form as a result of the use of special surfactants. The process of sulfide concentrate leaching with the use of sulfur dioxide is conducted at temperatures above the sulfur melting point (119°C) with distributed feeding of surfactant and under a partial pressure of sulfur dioxide of up to 0.3 to 0.5 MPa.

Jan 1, 2006

By Klara Kodrikova, Vera Kasparkova, Michaela Uhlirova, Karel Kolomaznik

"Potentially hazardous wastes from leather industry (blue shavings) are processed into various biostimulators within two steps. The first step takes place at high pH (11-12) and hydrolyzation is implemented with potassium alkali, in the second step the pH is lowered to 9 with phosphoric acid after enzymatic dechromation occurs. The resulting hydrolyzates were analyzed in the sense of molecular weight distribution and tested as biostimulators on rape (Brassica napus). The hydrolyzates can be also directly used as universal NPK fertilizers. It has been proved that the nitrate content in the edible parts of tested vegetables (radish, lettuce, and cucumber) was approximately 200 times lower compared to the vegetables fertilized with an inorganic nitrogen fertilizer. The harvests of vegetables fertilized with the hydrolyzate and the inorganic nitrogen fertilizer were almost the same.IntroductionDuring processing raw hide into leather (tanning processes), only 20% of the collagen material is used for the final product. The remaining 80% ends up as waste, both tanned and non-tanned. Non-tanned waste such as calcimine can be used for production of artificial collagen casings for sausages, gelatine and also in pharmaceutical industry as collagen capsulates. Further processing and recycling of tanned leather waste (especially chrome shavings) is more complicated. Although many technologies producing various quality collagen hydrolyzates have been developed and tested in laboratories, few have been implemented on industrial scale. A promising turn came in the works of ERRC USDA [1,2]. They worked out an enzymatic dechromation technology (hydrolysis) and achieved a considerable decrease of the amount of relatively expensive proteolytic enzyme, which solved the difference between the quality and price of the final product. The American experience of enzymic hydrolysis were applied on industrial scale in the Czech Republic, where a plant was built with daily processing capacity of 3 tons of chrome shavings. The experience of real operation was published in [3] and the cooperation between the Czech Republic and USA partners resulted in a patent [4]. The main asset of the patent was the use of volatile organic bases in the hydrolysis process giving high quality and cheap hydrolyzates with low ash content."

Jan 1, 2008

By G. C. Yao

Iron and silicon impurities can form needle and branch shape intermetallie compounds in molten aluminum when there is no manganese. It is difficult to separate them from molten aluminum by electromagnetic separation. The Fe-Si-AI and Fe-Al intermetallic compounds were transformed into Mn-Fe-Si-Al and Mn-Fe-Al compounds by the addition of manganese into molten aluminum. In molten aluminum the morphology of these intermetallic compound particles is lumpish and spherical. Migration resistance of these impurity particles is small, which is beneficial to separation. FeSiMnA4 and FeMnAI6 are paramagnetic. These impurity particles can be moved by magnetic force and can be separated from the molten aluminum.

Jan 1, 2003

By B. S. Boyanov

The hydrometallurgical technology for zinc production in Bulgaria is characterized by the use of considerable quantities of imported zinc concentrates and several kinds of Bulgarian ones which are quite different in chemical, phase and granulometric compositions. In this connection, 7 sulfide zinc concentrates (Bulgarian and imported ones) were investigated by chemical analysis, DTA, TGA, X-ray diffraction analysis, sieve analysis. The accomplishment of optimal mixing of concentrates and providing stabile mix composition for a long period of time of roasting in fluid bed furnace is a task of primary importance in the technological process control in zinc hydrometallurgy. This can be achieved using mathematical optimization methods.

Jan 1, 2006

By M. I. Zinigrad

A model of an ideal associated solution is presented. This model takes into account the existence of complexes of various compositions, sizes and geometries and allows calculating thermodynamic properties and phase diagrams of binary alloys. The model has been used formerly to calculate thermodynamic parameters and the position of the liquidus line for binary eutectic systems and also those having a stable compound in the solid phase. In all the cases the model parameters were not adjusted rather estimated from melting temperatures of the components. The recent studies dealt with the influence of arbitrary-stoichiometry associates on the equilibrium thermodynamic properties of liquid alloys. The application of the model to eutectic systems and systems having an unlimited solubility in solid and liquid states close to liquidus has been considered. It was shown that if the difference in melting temperatures of the components was small, different types of fusibility diagrams were possible: eutectic diagrams, cigar-shaped diagrams or diagrams with upper or lower azeotropic points. Peritectic transformations could take place when the difference in melting temperatures of the components was large. The present work is devoted to calculation of phase diagrams and thermodynamic properties of binary systems on the basis of chrome.

Jan 1, 2006

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By Shuo Wang, Yu Wang, Bing Xie, Rui Tang, Hong-Yi Li, Kun Wen

"During present converter vanadium extraction process, phosphorus could not be removed from hot metal due to absence of CaO in slag though it is an efficient way for vanadium extraction. In order to improve the phosphorus remove and produce CaO-containing vanadium slag, which could be directly used in subsequent roasting process, during the converter vanadium extraction process, lime dissolution in FeOx-Si02-V203-Ti02 slag was investigated by using a rotating cylinder technique and the slag-lime interface was characterized by SEM/EDS. Results showed that changes in the slag chemistry and phase compositions during the lime dissolution process were similar to that in CaO-Si02-FeOx based slag during the BOF process. The V and Ti in the slag were expected to diffuse into the lattice of2CaO·Si02 solid solution, which formed a rather thinner layer in thickness at the slag-lime interface than that in BOF process, leading to improvement of lime dissolution in the slag.IntroductionVanadium is important material that widely applied in industries. The traditional technique to extract vanadium was to leach vanadium after sodium salt roasting. However, the sodium salt roasting process has several problems including lower yielding rate[!] and environmental pollution[2]. Therefore, the more environment-friendly technique of calcium roasting[3-4] was proposed. In order to increase roasting efficiency of vanadium slag, it is essential to study the dissolution/reaction mechanism between lime and vanadium slag. Many investigations about the dissolution reaction of lime in molten slag have been carried out from the standpoints of rapid slagging to De-Pin steelmaking process[5-6]. However, their studies were focused on BOF slag and the reaction mechanism between solid lime and slag containing vanadium has not been reported yet. In present work, the dissolution process was studied with rotating cylinder technique and the reaction interfaces were observed and analyzed by SEM/EDS to elucidate the dissolution mechanism of lime in vanadium slag. This work was supported by National Natural Science Foundation of China No. 51090382."

Jan 1, 2013

By Gary Kordosky

Equilibrium modifiers, first introduced into copper solvent extraction reagents in the late 1960?s, are widely used. The properties of various equilibrium modifiers with respect to copper extraction, selectivity, reagent stability and entrainment are discussed and some conclusions are drawn relating the structure of the modifier to the properties of the modifier. A new highly selective, low viscosity modifier is also introduced.

Jan 1, 2003

By Tangstadm Merete, Eli Ringdalen

"This paper presents an overview of results from The Norwegian Research Institution SINTEF and the Norwegian University of Science and Technology, NTNU regarding new and ongoing research in silicon production. The main studies are related to condensation of SiO gas and cavity formation. If SiO gas condensation is increased at the top of the furnace resulting in SiO content in the off-gas closer to equilibrium, the Si yield will be increased significantly. Experimental work, simulating a cavity under industrial conditions, has shown that the cavity grows downwards from one layer. Physical appearance of zones in industrial furnaces, and selected reactions in these, are discussed based on results from excavation of industrial furnaces and results from laboratory experiments. Experimental studies of reaction rates for the formation of SiO are presented. Quartz properties are demonstrated to vary between differing quartz types and the effect of this is discussed.Introduction Both the theoretical and industrial issues associated with the production of silicon are described in detail in the textbook written by Schei et al [1]. This book covers the knowledge of silicon production process up to 1998. Together with the work by Myrhaug [1] and by Aasly[2], this is the main basis for this paper. Recent and ongoing research at SINTEF and NTNU focusing on production of Si and SiO in the high temperature zone, dissociation of SiO and condensate and cavity formation will be discussed."

Jan 1, 2012

By George R. St. Pierre

A method for the quantitative description of activity interactions between solutes in a metallic solvent which is consistent with stalistical thermodynamic principles is presented. The chemical potential of a solute in an alloy is derived from the weighted mean of its values in the individual solvent components, µi = S?jµi(i). The weighting factors, ?j, are obtained from the distribution functions. The resulting equation contains far fewer adjustable parameters than the Epsilon Formalism and because of its correct functional form it provides an improved fit to the available data on a variety of alloy systems containing oxygen, carbon, sulfur, nitrogen, and hydrogen. For a binary metallic solvent ( A, B ) containing a solute (i), it is shown that

Jan 1, 1995

By V. Jiricny

The novel spouted-bed electrode (SBE) is a cathode system where copper is deposited at a high current density in a moving bed of copper particles. Preliminary results on the deposition of copper from acidic sulfate electrolytes using this novel cathode system were described during Copper '95 conference. Despite a high current density, the electrical energy consumption was equal to or lower than that in the conventional electrowinning. The present paper describes more investigations on SBE. The SBE consists of copper particles with approximately 1 mm diameter onto which copper is deposited from acidic sulfate electrolyte whose composition is similar to conventional electrowinning. Three types of anodes were used in conjunction with the spouted-bed cathode, namely, DSA anode for oxygen evolution, and two novel anodes. One anode is less expensive than DSA; however it showed much promise in energy consumption. At a superficial current density of 2200 A/m2, the energy consumption was around 1.0 kWh/kg copper. The research activities described in this paper were supported by BHP Copper.

Jan 1, 1999

By K. A. Lewandowski

Agglomeration of ore can be used to immobilize fine particles during heap leaching by agglomerating them into granules. Without agglomeration, the fine ore particles can migrate within the heap, clogging flow channels and producing large areas where access of solution to the ore is very poor. The benefits of agglomeration are well-known in gold heap leaching operations, which can be effectively agglomerated using binders such as Portland cement due to the alkaline leaching solutions used. However, agglomeration has not been very effective in the heap leaching of copper ores, because these ores require an acidic leaching solution. Acid destroys the effectiveness of most binders, causing the agglomerates to disintegrate as soon as the leaching solution is applied. In order to gain the benefits of agglomeration in copper heap leaching, an economical, acid-resistant binder is needed. The two issues that needed to be addressed were: 1) Lack of effective methods for evaluating binder acid resistance before performing expensive, time-consuming, full-scale heap leaching tests, and 2) The vast majority of known binders react poorly to acid conditions, and so a basis was needed for determining which binders are most likely to be acid-resistant. In this paper, the development of two new tests for evaluating binder acid resistance in the laboratory are described. The ?soak test? determines the degree to which agglomerates disintegrate and release fines on contact with acidic solution, measuring the relative quantities of fines released by agglomerates made with different binders under controlled conditions, and serves as a rapid means for comparing large numbers of binders. The ?percolation test? measures several different parameters to determine how a binder is likely to perform in heap leaching: 1) the degree of ?slump? and compaction of agglomerates as they are wetted by acidic solutions; 2) the hydraulic conductivity of the agglomerate bed; 3) the migration of fines through the bed as the solution flows through it; and 4) the quantity of liquid retained in the agglomerates after they are drained. Using these tests, a broad spectrum of binders were examined. Soak testing determined that the most acid-resistant binders were nonionic polymers. Five of these binders were further evaluated using percolation testing.

Jan 1, 2006

By K. Osseo-Asare

Third phase formation, the separation of a solvent extraction organic phase into two liquids, is generally attributed to the limited solubility of the extracted complexes in the hydrocarbon diluents. Much of the research on third phase fomiation, therefore, emphasizes experiments designed to establish the stoichiometry of the species responsible for the limited solubility. This work offers a different approach, based on the recognition that the solvent extraction third phase, in fact, corresponds to the middle phase in a microemulsion fluid system. Using the tri-n-butylphosphate (TBP)-diluent-water-electrolyte system as a model system, current concepts of microemulsion phase behavior are utilized to develop a general framework for interpreting and predicting the patterns of phase behavior in solvent extraction systems.

Jan 1, 1999

By Roberto Parra, Roberto Parada

"A novel process for minor elements control in copper pyrometallurgical production is proposed based on a theoretical analysis and the results of an experimental program. Its application can solves operational problems related to volatile elements that determine pollutants gas emissions and the final quality of anodes. The process considers a calcination of mixtures of the dust with sulfidizing agents such as dirty copper concentrate or elemental sulfur at temperature under 800 °C. The product are a clean calcine that recovers all the Cu content on the dust and a gas stream that collect the minor elements as sulfides species. The calcine can be returned to the smelter avoiding the As increasing in the circuit and so on, the capacity for the treatment of dirty concentrates for the smelter can be higher. The possibility to apply vacuum in the calcinations step can decrease the operation temperature. The solid condensed from the gas has different options for its stabilization, with the advantage that this stream represents few mass with high As content.IntroductionThe control of undesired minor elements (IVIES) in conventional pyrometallurgical copper production is especially relevant for ore deposits associated to Andes region. The concentrates that are being produced present every time higher levels of volatiles and harmful elements: group Va (As, Sb and Bi), Pb, Zn, and Sn."

Jan 1, 2008

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Pedro Morales C.

From its beginning in the 1970s, the Teniente Converter has consistently achieved continuous improvement, and has contributed to the competitiveness and sustainability of Codelco's copper operations. The later introduction of the Slag Cleaning Furnace technology has helped to create a full technology package, referred to as the Teniente Technology. This paper outlines the features of a new research and innovation program designed to bring the Teniente Technology as a modem, competitive technology into the 21st century. The overall objectives and features of the program are described and discussed. It is fully anticipated that these activities will help position the Teniente Technology as a world-class modem technology, well-integrated and operating in a fully continuous mode in conjunction with the other units at the plant, a competitive technology which operates in harmony with respect to environmental regulations.

Jan 1, 1999