Search Documents

By R. Padilla, M. C. Ruiz, R. Villa

"Bismuth is an impurity in copper minerals where it occurs mainly as the mineral bismuthinite (Bi2S3). In smelting of copper minerals, most of the bismuth reports to the white metal, as a result, a substantial amount of bismuth accompanies the copper to the electrorefined cathodes. Thus understanding the behavior of Bi2S3 at high temperatures is crucial to eliminate bismuth before electrorefining. In this paper, some experimental data on the decomposition/volatilization of bismuthinite in nitrogen- oxygen atmospheres is discussed. The results indicated that in nitrogen atmosphere, bismuth volatilization occurs through a fast decomposition of bismuthinite to metallic bismuth and sulfur with subsequent volatilization of bismuth in the range 850-1100 °C. Similarly, in the presence of oxygen, bismuthinite decomposes to bismuth too, followed by oxidation to the non-volatile bismuth trioxide at temperatures higher than 750 °C. Both, temperature and partial pressure of oxygen affect significantly the bismuth volatilization and the oxidation rates.IntroductionCopper sulfide minerals are the major source for the production of metallic copper by pyrometallurgical processes, which are the dominant processes in the production of copper by selectively oxidizing the sulfide sulfur to SO2 and the accompanying iron in the concentrates to iron oxide, which can be conveniently removed as a stable slag.Generally, copper concentrates contain some deleterious minor elements such as arsenic, antimony, bismuth and lead, which are present as sulfides. These elements depending on their concentration may originate problems in the copper smelting processes and they can ultimately lead to a final copper product with unacceptable high levels of impurities.During the treatment of these copper concentrates by smelting, the impurities generally distribute themselves in the condensed and gas phases and they are eliminated mainly through the gas phase [1-3]. Thus, smelter off gases contains substantial amounts of volatilized impurity elements. For example, in the case of bismuth, the estimated distribution of bismuth in flash furnace smelting [2] was 15 % in the matte, 5 % in the slag and 80 % in the gas phase, and recently, for Outokumpu flash smelting Davenport [3] reported the distribution of bismuth as 30-75% in matte, 5-30% in slag and 15 -65 % in the off gas."

Jan 1, 2011

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The modification of structural clays by chemical processes is a common method. It usually uses strong inorganic acid attacks, aiming at improving the clay’s properties and applications. Among the applications are its use in clay-polymer nanocomposites, cosmetics, medicines, and bleaching clays. Tests using acid attack to modified Brazilian bentonites were successfully performed and, resulted in significant improvement in the clay properties. This paper discusses the use of a Brazilian bentonite modified by acid attack as bleaching clay. The treated bentonite samples were characterized by XRF, specific surface area (BET) and SEM/EDS. The treated clay exhibited improved bleaching capacity for Brazilian nut oil and other Amazonian oils.

Mar 1, 2018

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Dengfu Chen, Yi Yang, Chunmei Chen, Mujun Long, Shikai Gong, Junhao Sheng, Tao Liu

The relationship between thermo-physical properties of petroleum coke and temperature is of importance for determining of the operating parameters during the calcining graphitization process. In this paper, the variations of thermo-physical properties of petroleum coke versus temperature were investigated, such as the DSC-Tg curve, the specific heat capacity, the thermal diffusion coefficient, the thermal conductivity, and so on. The thermal analysis curve of petroleum coke showed synchronous thermal hysteresis at higher heating rates, indicating that a larger heating rate will cause delay of thermal effects. The thermal diffusivity of petroleum coke decreased during the calcining process. With increasing temperature, coefficient of heat conductivity and specific volume heat of the petroleum coke increased with a decreasing variation rate. The research provides a database for the calcining graphitization process of petroleum coke.

Jan 1, 2015

By Huaming Yang

The vanadium-doped SnO2 nanoparticle was synthesized by the co-precipitation reaction and subsequent calcination from the vanadium(III) chloride and tin(IV) chloride. The crystal size, pore size distribution, micrograph and properties of the nanocrystalline powders were examined by differential thermal analysis (DTA). thermogravimetric analysis (TGA). X-ray diffraction (XRD), desorption isotherm (Barrett-Joyner-Halenda method) and transmission electron microscopy (TEM). Thermal treatment of the precipitate powder at 600'C led to the formation of crystal0nmincrystal size. Most of the pores in the narmparticle are about 5~15nm in diameter. Effect of doped vanadium on the crystal size of the nanoparticle was discussed.

Jan 1, 2003

By Huaming Yang

The vanadium-doped SnO2 nanoparticle was synthesized by the co-precipitation reaction and subsequent calcination from the vanadium(III) chloride and tin(IV) chloride. The crystal size, pore size distribution, micrograph and properties of the nanocrystalline powders were examined by differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD), desorption isotherm (Barrett-Joyner-Halenda method) and transmission electron microscopy(TEM). Thermal treatment of the precipitate powder at 600°C led to the formation of V -SnO2 nanoparticle of -10mm in crystal size. Most of the pores in the nanoparticle are about 5~15nm in diameter. Effect of doped vanadium on the crystal size of the nanopartic1e was discussed.

Jan 1, 2003

By Qing-Yun Huang, Xiao-Yi Zeng, Bing Xie, Hong-Yi Li, Jia-Rong Yan

"In order to utilize vanadium resource in vanadium-titanium magnetite ore efficiently, vanadium distribution ratio between hot metal and slag should be improved during BF process, meanwhile the precipitating of Ti(C,N) in slag must be minimized. Effects of temperature, Ti02 content in the slag and basicity on vanadium distribution between slag and hot metal were investigated by experiment and thermodynamic calculation. The results indicated that high temperature, low Ti02 content and high binary basicity of slag were beneficial to increase the vanadium distribution ratio. The effects of temperature and Ti02 content in slag on vanadium distribution were stronger than that of slag basicity.IntroductionVanadium is an important element that is widely used in industrial fields. Most of vanadium resource is hosted in vanadium bearing titanomagnetite [l]. Vanadium bearing titanomagnetite is thus one of the domainate raw materials to produce the vanadium products. In other words, the comprehensive utilization of vanadium bearing titanomagnetite is beneficial for vanadium resource utilization. Vanadium bearing titanomagnetite sources are abundant in Pan Xi of China [4]."

Jan 1, 2013

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By Nan Zhang, Lei Zhang, Gai-feng Xue, Lina Wang, Pu Liu

"A novel ß-diketone modified silica gel was synthesized by a simple reaction. The prepared material was characterized by diffuse reflectance FTIR spectroscopy and it was used for the adsorption of heave metal ions in the industrial waste water. The main parameters affecting the sorption of heavy metal ions, including pH, water flow rate, and elution, have been investigated in detail. Under the optimized operating conditions, most of the targeted heavy metal ions could be removed. The material could be simply regenerated by hydrochloric acid solution. The method is rapid, selective, economic and applicable to the removal of heavy metal ions from industrial waste water.IntroductionToxic organic pollutants and heavy metals ions mainly from industrial activities such as plating, metallurgy and dyeing industries, are a threat to human health and the surrounding environment, because of their toxicity and persistence after being released into the natural environment [1]. These pollutants must be removed or degraded to an acceptable level, before being discharged to the receiving waters. Therefore, detection and determination of heavy metal ions in industrial waste water is very important.Inductively coupled plasma optical emission spectrometry (ICP-OES) is the most used technique for the determination of heavy metal ions because of its capability for rapid multi-element detection over a wide concentration range and with relatively low detection limits. Compared to other techniques such as neutron activation analysis (NAA), X-ray fluorescence spectrometry (XRF) and inductively coupled plasma mass spectrometry (ICP-MS), ICP-OES has the above advantages. Some constituents in industrial waters, such as organic compounds and inorganic salts, may cause matrix effects. In order to achieve accurate and reliable results, an efficient preconcentration of heavy metal ions and their separation from the matrix are usually required."

Jan 1, 2012

By Aichun Dou

Au-Sb alloy sample in which the total amount of Cu and Ni is below 25% (wt. %). In practice, Cu and Ni were difficult to be dissolved in sulphuric acid solution by oxidative leaching under the atmospheric pressure conditions, because of the lower concentration of Cu and Ni in the sample. In this paper, pressure oxidation leaching in sulphuric acid system (POLS) followed by hydrochloric acid leaching (HAL) was employed to remove impurities in the Au-Sb alloy. The effects of variables in POLS on leaching ratios of different metals were investigated in detail. Under the optimal conditions: the concentration of H2SO4 is 1.5 mol/L, liquid-solid ratio is 7:1, the amount of oxidizer is 1.2 times of the theoretical amount, leaching time is 4h and leaching temperature is 427K, the leaching ratios of copper and nickel reached up to 99%, antimony, lead and silver were not dissolved in dilute sulphuric acid solution. The residue from POLS was then treated with hydrochloric acid solution in fixed conditions, the leaching ratio of antimony reached over 92%, the grade of gold in the ultima residue was enriched up to 66%.

Jan 1, 2016

By Kenji Monden

A simple technique is presented to evaluate optical property of biomimetic microlens array (BMA) as an antireflective surface on a polydimethylsiloxane (PDMS) sheet. The integration of these structures is done by a thermoforming process. We have only UV-VIS spectrophotometer for optical evaluation apparatus. The transmittance of the sheet is measured with angled sample holder. The 50 deg. transmittance of 270nm pitch BMA on PDMS sheet increases from 87 to 92% after the moth-eye structure is introduced. The transmittance of 350nm pitch BMA on PDMS sheet increases from 87 to 96% after the moth-eye structure is introduced. The transmittance increases with increasing pitch of BMA. The results obtained using UV-VIS spectrophotometer with handmade sample holder.

Jan 1, 2015

By H. Fukuyama

The wetting behavior of single crystalline MgO by fayalite-type slag melts has been studied by the sessile drop technique incorporated with high temperature X-ray radiography. The experiments were performed under oxygen partial pressures of 10-6 and 10-4 Pa at 1473 K. Mass ratios of iron to silica, Fe/Si~, in the slag employed were 1.4 and 2.0. To investigate the interfacial reaction, experiments using high density MgO crucibles were also conducted. The reactions at the interfaces were examined by Electron Probe Microanalysis. The contact angles between the slag melts and the MgO substrates were found to be relatively low, ranging from 30 to 10 degrees. The surface tension of the slag was 0.4 N/m for a slag of Fe/Si02 = 2.0. Two phases, magnesiowiistite and olivine, were observed at the interface. Interdiffusivity in magnesiowiistite solid solution was determined as a function of iron oxide content. Phase relations between magnesiowilstite and olivine, and the growth rates of both phases, are also discussed

Jan 1, 1996

By C. E. Abbey, M. S. Moats

It is well known that the addition of cobalt to copper sulfate — sulfuric acid electrolytes decreases the overpotential for oxygen evolution and decreases the rate of corrosion of Pb–Ca–Sn anodes. This effect, however, has not been ade- quately quanti fied in the presence of iron and manganese in this type of electrolyte. This work provides quanti fiable data on the effect of cobalt concentration in the range of 0 –0.6 g/L in synthetic electrowinning electrolytes with and without the presence of iron. The effect of cobalt on anode potential was determined using 2 and 24 h chronopotentiometry experiments. As expected, Pb–Ca–Sn potentials increased with decreasing cobalt concentration over the range of 0–0.6 g/L Co with and without the presence of Fe. Two regression models were developed to allow plant operations the ability to predict anode potentials as a function of cobalt concentration with or without iron in the electrolyte.

Mar 1, 2017

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By James T. Skoch

With the ongoing pressure on the secondary aluminum business to limit the amount of waste generated from processing aluminum dross, it becomes very advantageous to preprocess the dross to reduce waste. The advantage of preprocessing is that it significantly reduces the oxides and salt cake generated when melted. Various products can be produced from the oxides for the steel industry. The following paper will demonstrate that removal of oxide fines before melting will result in large volumes of material not being landfilled. We will show that the end result of this technology is to significantly reduce the amount of salt cake sent to a landfill while maximizing the recyclability of the aluminum dross.

Jan 1, 1995

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya, Paul Cilino

"This paper focuses on generating a quantitative microstructure prediction model for Scanning Laser Epitaxy (SLE) process based on coupled flow-thermal modeling using Finite Volume method. SLE is a laser-based additive manufacturing process for the deposition of equiaxed, directionally solidified and single-crystal nickel superalloys through the melting of alloy powders onto superalloy substrates. In the current work, the detailed effects of natural and Marangoni convection on the flow field are studied and the results are analyzed in terms of the temperature gradient, vorticity parameter, melt pool dimensions and mushy region extent. The detailed property data of the processed superalloy and the laser scan path are incorporated in the model to predict the microstructure in realistic scenario. An optimization study is carried out to evaluate the critical parameter values at which the columnar-to-equiaxed and the oriented-tomisoriented transition take place. This work is sponsored by the Office of Naval Research through grant N00014-11-1-0670.IntroductionSLE is a laser-based additive manufacturing process for the creation of structures in equiaxed, directionally solidified and single-crystal nickel superalloys through the selective melting and resolidification of superalloy powders. In SLE, a tightly focused laser beam is guided by a highspeed galvanometer scanners allowing for tight control of the amount of energy being applied to the top of the powder bed, as well as the speed at which the melt pool moves across the substrate. Under the proper operating conditions and with sufficient substrate meltback, the solidification microstructure follows the morphology of the underlying substrate, allowing for directional and even SX growth.Several reports on the modeling aspects of laser cladding-based additive manufacturing approaches can be found in the literature. Approaches based on Finite Element Methods (FEM) and Finite Volume Methods (FVM) are employed for the thermal modeling of the system [1, 2]. Gaumann coupled the Columnar to Equiaxed Transition (CET) modeling with the Rosenthal solution in earlier work based on laser cladding [3]. Rappaz et. al. provided a detailed modeling of the microstructure/columnar orientation based on the solidification velocity and crystalline orientation [4]. This approach is based on the selection of the growth direction that closely follows the melt pool normal direction. Later on, substrate orientation is also taken into account [5, 6]."

Jan 1, 2013

By Ting Liu, Qian Li, Peng Deng

The wastewater containing Hg2+ and Pb2+ does great harm to the environment and human bodies. Traditional wastewater treatment cannot fundamentally put a stop to heavy metals pollution for producing secondary pollution. In this paper, Hg2+ and Pb2+ in wastewater were removed and recovered by sulfide precipitation- flotation. Sodium sulfide was used as precipitant and butyl ammonium aerofloat was used as collector. Results indicated that Hg2+ and Pb2+ could be reduce to less than 0.03mg/L and 0.16mg/L respectively by both coprecipitation- floatation and fractional precipitation- floatation. In these two methods, fractional precipitation flotation could not only remove Hg2+ and Pb2+ from wastewater, but also could recover mercury and lead effectively. The infrared spectrograms showed that the adsorption between butyl ammonium aerofloat and mercury precipitate or lead precipitate is chemisorption.

Jan 1, 2015

By Jong-Shin Chang

The Onsan smelter has tried to do various activities to decrease operation costs. With several expansion projects, the Onsan smelter has aimed at not only a quantitative growth but also qualitative growth through efforts improving operations equipment and processes. Activities to reduce operation costs have been one of those efforts. In particular, the energy cost of operation has been a main target for reduction. The activities to save energy have been carried out in two ways. One is to recover and utilize waste heat as much as possible and another is to replace existing equipment and processes with more energy-efficient ones. This paper reviews recent improvements and future plans for energy saving activities at the Onsan smelter.

Jan 1, 2006

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By A. E. M. Warner

At the Copper Cliff Smelter, Inco Limited has extensive experience in converting primary smelting mattes over a broad range of nickel/copper ratios and compositions. In the past 35 years, technology developments at Inco have reduced the number of Peirce-Smith converters in Nickel/ Bulk (nickel-copper matte) service from 13 to the current 5. This paper will discuss: ? The performance and life of ?stretch? 13.7m shells versus conventional 10.7m converters. ? Process control and information system development from the early 1980?s to view converter aisle status on a continuous basis to the recent central control of the stretch shells. ? Nitrogen cooling of finishing matte from plant testing to implementation in the early 1990?s to replace the dedicated cooling converters. ? The impact on converting of changing the smelter flowsheet in the early 1990?s. ? A current program to develop a converting strategy for the future to address environmental issues and profitability.

Jan 1, 2005