Search Documents

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By D. D. L. Chung

"In-situ network composites are composites in which the filler network is formed during composite fabrication, in contrast to ex-situ networks which are formed prior to composite fabrication. A homogeneous in-situ network composite has the entire network at the same composition; a heterogeneous in-situ network composite has different parts of the network at different compositions. The homogeneous network composite is made either by the Method of Molten Filler Flow or the Method of Dissolution and Deposition; a heterogeneous network composite is made by the Method of Liquid-Phase Networking. Examples include polymermatrix and metal-matrix composites.IntroductionNetwork composites refer to composites containing a continuous three-dimensional network as the filler. These composites are attractive in their lack of delamination failure, which is usually characterised by two-dimensional composites. The filler and matrix in a network composite can be considered two interpenetrating networks. The mechanical interlocking of the networks adds to the cohesion of the composite. In cases where the filer is much better than the matrix in a certain property, the network nature of the filler makes the filler highly effective in improving that property in the composite in all directions. The property desired in the composite may be high strength, high modulus, low coefficient of thermal expansion, high thermal conductivity, or low electrical resistivity."

Jan 1, 1994

By Kazuaki Mita

There are various intermetallic compounds in the Zn-Fe system. We synthesized them at about 673K. A specimen was examined chemically and X-ray diffraction was applied to ensure the formation of intermetallic compounds. Material containing two phases was placed in a Knudsen type effusion cell and the mass spectrum studied to evaluate the vapor pressure of zinc. The thermodynamic properties of intermetallics was then evaluated through measured intensity.

Jan 1, 1999

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By Qingzhu Li

The adsorption process of Pb2+ from aqueous solutions by spent grains modified with Imol/L NaCI solution was investigated. The effects of solution pH, contact time, adsorbent concentration, initial Pb2+ concentration, particle size on Pb2+removal were also studied. The initial adsorption process was rapid and 90.35% of Pb2+ adsorption occurred within 30 min. The absorption equilibrium was obtained at 4h. When pH was 5.5, Pb2+ concentration in aqueous solutions decreased from the initial content of 20 mg/L to 0.0 I mg/L after 5 hours by application of IOg/L adsorbent at 25?C, Pb2+ removal efficiency reached up to 99.95% and the Pb2+ remaining in aqueous solutions was under China Sanitary Standard for Drinking Water (GB5749-85). Adsorption data fitted well with Lanf+muir and Freundlich models. However,Langmuir isotherm model was better to descnbe Pb- adsorplion than Freundhch model, mdlcatmg that the applicability of monolayer coverage of Pb2+ on the surface of adsorbent.

Jan 1, 2008

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By S. C. Sharma

The aluminium matrix composites with ceramic dispersoids can be separated by density difference concept. In the proposed work composite scrap is recycled using an oil fired furnace. The scrap is melted in the furnace and temperature is maintained below 740 degree centigrade. Because of the density difference the lighter dispersoids will float and heavier dispersoids will settle down. The clean melt is separated be removing the floating and settled disperssoils, and then filtering using ceramic filters.

Jan 1, 1995

By Junji Shibata

Through-hole copper plating is performed to make a multi-layer printed circuit board. The through hole plating is first carried out by Pd catalyst treatment, followed by copper non-electric plating. The amount of Pd catalyst used in one plant is about 0.25-2 m3/month (8 g/dm3 PdCl2 base) depending on the plant scale, and the cost of the catalyst reaches 17,000¬I35,000 US$/month. In this study, the flow and material balance of a Pd in Pd catalyst treatment process was investigated. About 60% of Pd catalyst adheres on the through-hole and other part of setup, while 25% is released into the washing liquor. Pd in the washing liquor should be collected by a suitable method like a pressure filtration using diatomite. The material balance of Pd in Pd catalyst treatment process and the recovery method of Pd from waste solution containing Pd catalyst was investigated.

Jan 1, 2003

By E. Gutierrez-Miravete

Hot pressing processes are widely used to shape metallic, ceramic, and glass components. The process is an essential step in manufacturing ceramic fibre-glass matrix composites. The paper describes the use of computer simulation by the particle method, to the analysis of the deformation and flow of glass during hot pressing. The hot glass is represented by an assembly of interacting particles which deform in response to the applied pressure. The results, which should be regarded as complementary to continuum-based studies, provide useful insight about the hot pressing process.

Jan 1, 1990

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. Assis, Henry A. Colorado

The fique fiber is an important natural fiber, originally from Colombia where it is used for sacks and crafts while its plant is used to contain slopes. However, few studies were realized with the fiber obtained from the fique plant leaf, its mechanical properties are superior in many aspects in comparison to some other lignocellulosic fibers. This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of a fabric made of fique fiber by means of Charpy impact tests. It was found that the addition of fique fabric results in a marked increase in the absorbed energy by the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that transversal rupture through the fique fabric interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Mar 1, 2017

By Mei Yang, Wei Gao, Jian Yang, Qingcai Liu, Wenchang Xi

"TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel technology. In APCVD method, TiC14 and O 2 were used as reaction precursor. TiC14 was gasified by using N2 as carrier gas which was controlled to 500sccm. Its reaction temperature and reaction time were limited to 773K and 30min respectively. The physical properties, SEM and SEM-EDX of the TiO2-cordierite carrier and the properties of SCR catalysts prepared by these carriers have been tested. The tests showed that TiO2 loaded by APCVD method were of graininess shape and even accumulation. The loading rate of TiO2 and the specific area of carrier sample were increased 114% and 21 % respectively comparing with sol-gel technology. In the result of sol-gel method, the maximal difference of Ti content was 66.92%, while the result of APCVD method was 18.89%. It demonstrated that TiO2 was uniformly attached with the cordierite ceramic by using APCVD method, which would ensure more active ingredients well loaded on the Ti02-cordierite carrier. This difference made the denitrification ratio of catalyst prepared by APCVD method was 8.1 % higher than that of catalyst prepared by sol-gel method.IntroductionIn recent years, the emission of NOx, which were caused by coal-fired power plants, has gotten more and more attention. SCR (selective catalytic reduction) is the most effective technology to DeNOx [ll. The core technology of it is the catalyst. The SCR catalyst usually uses Ti02 as the carrier, and V2O 5 as the active component [2, 3] . However, the thermal stability and mechanical properties of TiO2 carrier are unstable, which would influence the performances of the catalyst. The commercial catalyst generally uses WO3 or MoO3 to promote its heat stability at present [4-7] Besides, TiO2 is expensive. Compared with TiO2, the cordierite is of good thermal stability and lower price. So loading Ti02 on cordierite porous ceramic as carrier to produce SCR catalyst is of good prospects [S, 91 • Currently, TiO2 is usually loaded on cordierite by the sol-gel method. But some research has shown that the sol-gel method easily reduced the loading performances of TiO2, such as distribution, combination, etc. APCVD (atmospheric pressure chemical vapor deposition) has many advantages to preparing TiO2 films, such as high bonding strength, fast reaction rate and so on [l0-13l_ In this paper, TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel methods. The properties of the carriers prepared by the two processes have also been compared."

Jan 1, 2011

By K. J. Cathro

A hydrometallurgical process is described for the recovery of copper from chalcopyrite concentrates. The process is based on a cupric chloride leach, the concentrate having first been "activated" by heating it with sulphur at a temperature near 400°C. This activation process converts most of the iron of the chalcopyrite to pyrite, which is insoluble in the cupric chloride leachant. The copper is converted to the mineral idaite, which dissolves readily in hot cupric chloride: at 106°C, 98% of the copper is extracted in a three-stage countercurrent leach, the leaching tirqe being 1 hour per stage. The sulphur of the chalcopyrite appears as elemental sulphur, which is recycled for the activation of further concentrate, the final leach residue consisting of pyrite, plus the gangue present in the original concentrate. The copper extracted can be recovered by electrowinning, using a diaphragm cell. Current efficiency (one-electron basis) is about 70% but the cell voltage is only about 1 V, so that power consumption is three times lower than for the conventional sulphate electrowinning process. The leachant is simultaneously regenerated in the anode compartment. The behaviour of minor elements in the concentrate has also been studied.

Jan 1, 1976

Acid generation from reactive sulphide mineral tailings has become a major environmental problem in the mining industry. Initiation of chemical and biochemical oxidation reactions of the sulphide mineral leads to acid generation. A novel concept of safe disposal and utilization of reactive fine mill tailings is presented in this paper. The paper also presents the results of a preliminary laboratory experimental .study of the concept. The tailings are agglomerated using portland cement as a binder. The cold bonded agglomerates are encapsulated with other chemical additives to act as acid neutralizers, oxygen and ironoxidizing bactericides., The primary. factors influencing the choice of bacterfoides to inhibit the acid generating bacteria are their costs, toxicity and environmental friendliness. The paper discusses the utilization of agglomerated' products as aggregates for underground backfill, or as gravel for surface land cover.

Jan 1, 1991

By A. Rosenfeld

The feasibility of applying laser induced optical emission spectroscopy to the high speed sorting of mixed alloy aluminum scrap is investigated. The basic spectroscopy for analysing aluminum alloys for the major alloying elements over their full concentration ranges is established. Materials handling issues are also described and the components of an overall sorting system are presented.

Jan 1, 1995

By Mishark Nnabuchi

A heterojunction of PbS - CuS thin film has been grown on glass slides by SGT. The films were annealed for 1hr at temperature of 373K and 423K respectively. The optical properties were characterized using a UNICO UV - 2102 PC Spectrophotometer at normal incidence of light in the wavelength range of 200 - 1000nm. The minimum percentage transmittance was observed to be 34% for sample A and 25% for sample B within the same optical region. The band gap energy was determined from the spectra to be 2.05eV for sample A and 1.85eV for sample B which gave a band shift of 0.20eV. It can thus be concluded that the optical properties of the films within the VIS - UV - NIR can find application in solar thermal technology, particularly as antireflection coating, window materials and as good materials for selective solar cell fabrication.

Jan 1, 2010

By Yuan-bo Zhang, Gui-hong Han, Yan-fang Huang, Tao Jiang, Guang-hui Li

"Under isothermal conditions, the reduction behavior of oxidized pellets balled with bentonite was investigated with CO-CO2gas mixers in the temperature range from 900°C to 1100°C. The whole reduction of oxidized pellets was followed up by means of weight-loss technique. And the swelling index of pellets was examined by visualizing physical changes of pellet in a horizontal tube furnace. The results present that the reduction rate of oxidized pellets is increased with the increase of reduction temperature. While the swelling index is firstly increased and then decreased with the increase of reduction time and reduction extent, which can be ascribed to the disruptive stresses induced during the transformation of hematite to magnetite. The maximum swelling index is gradually increased with the increase of reduction temperature and CO content.IntroductionWith the rapidly development of iron and steel industry, direct reduction iron has been considered as one kind of high quality burdens in electric furnace steelmaking [1]. At present, ""Two-step"" coal-based direct reduction process, which employs oxidized pellets as raw materials, has been used in industrial production [2]. The reduction behavior of iron ore oxidized pellets has been becoming one of the most frequently studied topics in extractive metallurgy[3]. The heat and mass transfer in direct reduction processes results in a series of stepwise reduction reaction (hematite--magnetite--wustite--iron), accompany with the volumetric swelling of pellets[4]. A lot of literatures have been reported on the reduction model of ferrous oxides and swelling behavior of pellets. A. A. El-Geassy K, et.al [5-7] revealed that the reduction process was controlled by chemical reaction at early stage by employing pure Fe203 as raw materials and CO as reduction gas. Chen Y [8] made research on the reduction kinetics of porous oxidized pellets and obtained the rate constant and activation energy of at different reduction stage. In addition, the swelling and disintegration of iron ore pellets was affected by chemical composition of pellet and reducing parameters, which have been studied by numerous investigators [3,9, 1O]."

Jan 1, 2013

By Chr. Kersch

This project further develops supercritlcal fluid extraction as an industrial soil remediation process. Heavy metals are removed from sand using CO2, The effect of the type of complexing ligands, pressure and water content on the extraction efficiency is investigated.

Jan 1, 1999

By F. J. Tavera

The colloid flotation of lead carbonate precipitates in aqueous media is studied at a pH of 7. The flotation system consisted of five spargered flotation cells in a serial array. The flotation system was operated under controlled conditions of superficial air velocity, superficial liquid velocity, frother concentration, and collector concentration. The measured variables were gas hold-up, bubble size, superficial bubble surface flux, and lead recovery (reported to the concentrate). The experimental data show that it is possible to separate as much as 97% (w/w) lead from the aqueous media when the superficial gas velocity is 1 cm/s and the superficial liquid velocity is 0.19 cm/s.

Jan 1, 2006

By P. G. McCormick

The refining of rare earth metals by the direct solid state reduction of their respective chlorides during mechanical alloying has been studied. Erbium and gadolinium were synthesised by milling their respective chlorides with calcium. The mechanical alloying of SmC13 with calcium resulted in partial reduction of SmC12. Examination of the milled powders using X- ray diffraction and analytical electron microscopy has enabled characterisation of product structure and morphology. The synthesis of Fe17Nd2 by the mechanical alloying of NdC13 and Fe with calcium has also been studied. The Fe17Nd2 phase forms during heat treatment of the mechanically alloyed powder.

Jan 1, 1992