Search Documents

By Jason Eric Sallee

Ongoing operations at the Cyprus Miami Smelter involve the use of an electric furnace for settling of copper matte from discard slag. Proper operation of the electric settling furnace is a major factor in minimizing losses of copper to the discard slag. Recent test work at the smelter has shown improvement in the operation of the electric furnace with a subsequent improvement with regard to the copper losses. This paper presents a general discussion of the Cyprus Miami Smelter operation, past results with respect to copper losses, recent operational changes and test work, and the subsequent results.

Jan 1, 1999

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Leonard J. Friedman

The recovery of sulfur dioxide from metallurgical gases for the production of sulfuric acid has been an effective means of reducing sulfur dioxide emissions from non-ferrous smelters. Sulfuric acid has been produced from gas originating from fluid bed roasters, electric furnaces, reverberatory furnaces, flash smelting furnaces, Pierce Smith and flash converters, sinter machines, etc. The gas from each of these sources has a unique set of variables that affect the design and operation of the sulfuric acid plant. In addition, the sulfuric acid plant itself has been evolving, with new equipment designs and materials. This paper will review each of the unit operations in the gas cleaning and contact sections of the metallurgical sulfuric acid plant, discussing various equipment designs, materials and the handling of gas stream variables and impurities. The paper updates to 2006 previous works on metallurgical sulfuric acid plants by the authors.

Jan 1, 2006

By Magnus Ek

After the installation of three new converters as part of the recent expansion of the Rönnskär smelter completed in 2000 work continues to further improve the converter operation. The converter upgrade led to an increase in blister copper taps from 150 tons per batch to more than 300 tons. The total cathode copper production increased from 130,000 tons in 1999 to 230,000 tons in 2001, the first year in full production. In recent years focus has been to improve operating practise, maximize the blowing time, extend the converter campaigns hence to reduce the specific brick consumption and improve the converter slag composition.

Jan 1, 2005

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By Michael S. Moats, Daniel Kim, Shijie Wang

"The behavior and deportment of lead, arsenic, antimony and bismuth are critical in producing high quality cathode by copper electrorefining. A critical review of research related to these elements is presented along with a comparison to industrial data, where appropriate. These elements exist predominantly in the anode as complex oxides along die grain boundaries. Upon dissolution, Group 15 elements report both to the electrolyte and slimes while lead essentially enters the slimes. The deportment of the Group 15 elements appears to be influenced by several chemical interactions which are discussed. The effect of these elements on floating slimes and anode passivation is reviewed. Under normal electrorefining conditions, lead, antimony and bismuth are thought to enter the cathode through the encapsulation of slime particles. The literature indicates that arsenic enters the cathode predominately by electrolyte entrainment. Finally, areas for future research regarding these elements are presented.IntroductionControlling lead, arsenic, antimony and bismuth is critically important for the production of high quality cathode in copper electrorefining. The reasons for this are twofold. First, ASTM Grade 1 Cathode specifications [1] for these elements are low, as listed in Table 1. Second, they can affect the efficiency of the electrorefining process (e.g., through passivation, current efficiency, slime processing)."

Jan 1, 2012

By S. J. Kohut

Until recently SX-EW technology has only been used to produce conventional cathode for the cyclical commodity marketplace. Unlike electrorefining, SX-EW lends itself to the integration with the downstream manufacturing technologies for direct mine site production of value added products. The integration of SX-EW and downstream manufacturing results in the elimination of redundant process steps, the cost savings, and the access to value added product markets which can buffer the producer from swings in the cathode market. SX-EW production of copper powder and powder-based products has been demonstrated at the pilot plant level. The SX-EW process has been successfully redesigned to meet the more specific demands of engineered products. Challenges include the solution purity, the cell ventilation, the high current density operation and the product handling. Successful demonstration of mine site production of value added SX- EW products opens up new non-commodity marketplaces to the mining industry.

Jan 1, 1999

By Claassen J. O.

The Zinc Corporation of South Africa Ltd. (Zincor) operates an integrated roast ? leach ? electrowinning circuit. The efficient removal and control of iron forms an integral part of the process. Zincor developed its own iron removal process (Zincor Process), which was recently shown to be unique with some similarities to the para-goethite iron removal process. Newly developed operating parameters for iron removal are in the process of being implemented. These include a change in the pH-profile and operating temperature, the recycling of seed material and the utilisation of an alternative neutralising agent to aid iron removal. Some of these actions, together with the implementation of a pre-neutralisation step, new filtration equipment and control systems in Zincor?s Residue Treatment Plant have significantly reduced zinc losses associated with iron in calcine and the iron residue produced. This enabled Zincor to take a step closer to world-class zinc recovery levels of around 96% for a similar type of operation.

Jan 1, 2003

By A. N. Lasseigne

Hydrogen storage capabilities of LaNi5 intermetallic compounds were investigated utilizing the combination of thermoelectric power, Beeghly Ester-Halogen digestion, and Leco hydrogen determination. Thermoelectric power has demonstrated a rapid hydrogen assessment capability and can achieve the equivalent of the pressure-composition-temperature (activity) diagram. Effective use of hydrogen storage materials occurs in the two-phase, alpha+beta region of the PCT diagram. A thorough assessment of the content of each phase in this two-phase region to optimize performance of the hydrogen storage materials is described. Practices using the combination of these three analytical practices for rapid characterization of LaNi5intermetallic alloys are discussed.

Jan 1, 2006

By B. C. Jena

Activities of carbon, cobalt and nickel were evaluated in the ternary systems iron-carbon-cobalt and iron-carbon-nickel for the temperature range 1300-1600°C for cobalt and 1300-1700°C for nickel. The carbon activities were determined from the knowledge of activities (1) in the binary system iron-carbon, (2) in the dilute ternary systems and (3) from the knowledge of carbon saturation data. The activities were mathematically expressed with the Taylor series expansion of Wagner's interaction parameter formalism modified to suit concentrated solutions. The cobalt and nickel activities were determined from the knowledge of carbon activities by applying the Gibbs-Schuhmann integration and from cobalt and nickel activities in the binary systems iron-cobalt and iron-nickel. Partial molar enthalpies of mixing were determined based on the temperature behaviour of the activity coefficients.

Jan 1, 1992

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By J. D. Miller

Gold adsorption from cyanide solutions by activated carbon has been studied at great length during the past decade. Findings from past research are reviewed and discussed with respect to structural features of various carbons, including carbon black, activated carbon, graphite and diamond.

Jan 1, 1991

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981

By Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao, Guojing Hu

"The equilibrium between titanium ions and metal titanium was investigated in fluoride-chloride molten salt. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The equilibrium constant of the equilibrium between titanium ions and metal Ti was calculated in KCI-NaCl- 2.5wt %K2 Tif 6 at the temperature of 1073K.IntroductionTitanium, the ninth most abundant element in the earth's crust, is endowed with high strength, low density, excellent flexibility, strong spring back characteristics, high-temperature performance, corrosion resistance and biocompatibility. These characteristics make titanium eminently suitable to be used in aerospace, marine industries, and harsh chemical environments. Although it has many excellent properties, the application of titanium in industry was limited by its high-cost. Therefore, many methods have been investigated for producing high-purity titanium at low cost. Electrolysis, involving the extraction and preparation of pure metal from ore using an electrolytic process, is considered a promising method for titanium metallurgy. Many studies have focused on the electrochemical behaviour and electrodeposition of titanium in molten chloride, fluoride, and chloride-fluoride electrolytes (1-IOJ. The electroreduction mechanism of Ti3+ ions in molten alkali chlorides has previously been studied by several workers. Two reduction steps, Ti3+ -Ti2+ -Ti, have been observed in various molten alkali chlorides [IJ. One reduction step, Ti3+ -Ti, has been observed in alkali fluoride molten salts l21. The behaviour of Ti4+ in fluoride or chloride-fluoride molten salts has also been investigated in the literature; it was proposed that the reduction of Ti4+ ions in the molten salts proceeded in a two step process: Ti4+-Ti3+-Ti l3l or a three step process: Ti4+ -Ti3+ -Ti2+-Ti ri. 4l Indeed, the stability of the titanium oxidation states depends on the bath composition l5l. The valence state was Ti2+ in alkali chloride melts, which was a lower oxidation state and correspondingly, in alkali fluoride melts, the higher oxidation states ofTi4+ and Til+ were more stable.The aim of the present work is to explore the effect of F/Cl atomic ratio on the equilibrium between titanium ions and metal titanium in fluoride-chloride at the temperature of 1073K. The electrochemical properties of titanium ions in fluoride-chloride were studied on a molybdenum electrode by cyclic voltammetry (CV) and square wave voltammetry (SWV). The solubility product of the equilibrium between titanium ions and metal Ti was calculated."

Jan 1, 2012

By Jenq-Gong Duh, Jyh-Wei Lee

"Hard chromizing process is a method for developing a surface modified coating providing wear, corrosion resistance and high temperature surface protection. Two carbon steels with 0.45 wt% and 0.95 wt% carbon contents, respectively, were chromized with pack cementation process at 950'C for 4 and 9 hours, respectively. The phase transformation and microstructure phenomena of chromized coating layer and matrix of two steels were studied with X-ray diffractometer and electron probe microanalyzer. (Cr,Fe)23C6 and (Cr,Fe)7C3 carbides and (Cr,Fe)2N1-x nitride phases were observed on the chromized surfaces. The thickness of chromized layers obeyed the parabolic rate law. The mechanism and diffusional kinetics of the chromizing process were proposed. The diffusivity of chromium in the (Cr,Fe)7C3 carbide phase was calculated using the moving boundary method.IntroductionChromizing process is one of the surface treatment technologies that can produce a chromium contained surface layer with sufficient corrosion and wear resistance on the steel matrix [1-7]. The relatively low cost and no ""line-of-sight"" restrictions are main advantages of chromizing. Adequate bonding strength of these coatings to the substrate was reported [7]. Chromizing process can be classified into soft chromizing and hard chromizing [2]. Soft chromizing is applied to steels containing less than 0.1wt% carbon through which chromium will be diffused. High temperature oxidation resistance improvement is the main purpose of soft chromizing process. On the contrary, the hard chromizing can be applied to steel containing more than 0.3wt% carbon, and very hard chromium nitride and carbide layers will be formed on the surface, which are very resistant to wear, corrosion and temperature [5-7]. In the previous studies on the Fe-Mn-Al-Cr alloy [5,7] and carbon steels [6], the thickness (X) of chromizing layers was analyzed and found the parabolic rate Jaw prevailed:"

Jan 1, 2004

By Daniel Kittelty

A fully instrumented laboratory electrowinning cell has been used to produce nickel cathodes from synthetic solutions containing various impurities in order to evaluate the effects of both metallic ions and organic reagents (from prior solvent extraction and other processes) on the quality of the electrodeposited nickel. The conditions used were typical of those employed in industrial electrowinning operations. The impurities were found to alter the crystal size and shape, induce the development of hydrogen pits on the deposit surface, incorporate as metal hydroxide crystals in the deposit, and alter the internal stress and current efficiency. These effects have been interpreted in terms of previously established relationships between the solution composition and the physical properties of the cathodes. The incorporation of the common metal impurity ions into the deposit have been interpreted in terms of a mass transport controlled reduction or precipitation reactions. In particular, a low concentration of aluminium ions resulted in an initial highly deleterious effect, which was replaced by a positive influence at higher concentrations. A model which involves the buffering effect of the aluminium on the pH at the cathode surface has been proposed.

Jan 1, 2003

By Benjamin Vidales

Copper in concentrations above 0.5 weight percent in iron and steel causes hot shortness. This tendency is intensified in the presence of dissolved tin above 0.05 weight percent in the alloy. The understanding of the mechanism of removal of copper from molten iron and steel is of industrial importance. In this investigation, we present the experimental results of the removal of copper from molten iron using sulphide flux in the temperature range 1000°-1500°C. The solution thermodynamic properties of binary sulphide melts have been estimated by using the relevant phase diagrams and the behaviour of copper sulphide in these melts is discussed. The kinetics and thermodynamics of the removal reaction are also explained and, the experimental results are also reported showing the equilibrium distribution of copper and sulphur in molten iron.

Jan 1, 1995

By P. M. Pincheira Brown

The widely accepted inverse relationship between copper prices ail stocks, has been commonly used by analysts to explain the behavior of the copper market and to forecast film copper pries. However, empirical data have not shown such a clear relationship between copper prices and stacks. Existing evidence only indicates a weak tong-nut relationship that vanishes in some periods. In this paper a simple comprehensive model is provided which explains both parallel and opposite direction movements between prices and stocks. Former are explained mainly by stocks demand expansions-contractions while the latter are in essence due to increases in the supply curve. Furthermore, econometric estimations are provided, thus giving a powerful tool to forecast and explain price developments of the copper market.

Jan 1, 1999