Search Documents

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2 versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By P. Mercille, M. F. Nasmyth, J. G. Cooper

The turn of the century sees considerable activity in the zinc industry for the replacement or expansion of existing cellhouses, and the building of new cellhouses as part of new zinc projects. Aside from the cellhouse technology itself, numerous engineering and construction issues play a major role in the success of a project for replacing or building new cellhouses. The purpose of this paper is to bring to light and to address the engineering and construction factors which go beyond the selection of a cellhouse technology and which remain of key importance in implementing such projects. In addition, some implications of these factors for project costs will be illustrated.

Jan 1, 2000

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By W. E. Wallace

Rare earth elements combine with most, of the metallic elements. As early as 1971 over a thousand intermetallics had been identified and described(1) From a magnetics viewpoint, systems involving. the d-transition metals Fe, Co and Ni are particularly interesting. In these systems there are at least four significant interactions: R-R exchange (R - a rare earth), R-T exchange (T = a transition metal), R-R exchange and the crystal field interaction acting upon the. rare earth ion. There is complex interplay between these interactions leading to bewildering variety in their magnetic behavior., Because of this and in view of the commercial significance of some rare earth intermetallics, studies of these systems has been an unusually active area of inquiry for the past two or three decades. The large magnetic moment of many of the rare earths, viz., 10 µB per atom for Dy and Ho, 9 1B for Tb and Er, etc., attracted, attention many years ago to the rare earths as potential ingredients for alloys to be used in permanent magnet fabrication. The utility of a permanent magnet in high perform¬ance devices (travelling wave tubes, voice coil motors, brushless motors, etc.) is in large measure determined by its maximum energy product, (BH)max. [(BH)max is the maximum value of B (magnetic induction) and H in the 2nd quadrant of the hysteresis loop.] Enhanced atomic moment in princple can lead to increased B and a large maximum energy product. Until about 1970 the largest (BH)max value known was about 5 MGOe(mega-gauss Oersted). This was for A1NiCo - an alloy involving Al, Ni and Co. It was recognized that the rare-earths had the potential for much higher energy product; in the case of Dy the theoretical energy product is about 35.0 MGOe., 70 times that of Alnico. (Needless to say, this theoretical value has never been achieved.) Large-scale efforts began about 30 years ago to synthesize magnetic materials containing rare earths and which would be suitable for permanent magnet fabrication. It was recognized by Strnat(2) et al. that a material to, be useful in high energy magnet fabrication would have to satisfy three. criteria:

Jan 1, 1992

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994

By V. Madhusudhan Rao

Fly ash is a finely divide non ? combustible material obtained as a by ? product of coal combustion. It is a major by ? product of coal based thermal power stations. Until recent past it was considered as a waste and highly polluting material. However its formation can only be minimized by using suitable technology in the boilers. In recent past it is found that Fly ash has many end uses and it has proven itself to be a potential construction material. But the suitability of fly ash for various applications largely depends on the amount of unburned carbon, which is turn depends on the firing method. Fly ash samples from various power plants existing in India using a fluidized bed method and pulverized bed were analyzed and a comparison of these two firing methods was carried. This paper deals with the compositional requirements for fly ash used for the fabrication of insulating doors using AAC (Aerated Autoclave Concrete) and the methods employed to make fly ash suitable for this purpose. It also includes the latest ?U? beam technology for effective fly ash recycle. If the by products of coal combustion from power plants like fly ash as the paper stresses are utilized properly, it is not an exaggeration to say that power generation is possible with absolutely zero cost.

Jan 1, 2006

By M. Nienoord, O. S. L. Bruinsma, J. A. F. M. Schade Van Westrum, W. H. Sillekens, B. Mehmetaj

Recycling of aluminium is an effective way of enhancing the efficient use of energy and limiting the burden on the environment. Where cascade recycling is an established way of using reclaimed aluminium, closing the recycling chain is currently hampered by the unavailability of suitable techniques for refining contaminated scrap on an industrial scale. To overcome this problem, purification based on fractional crystallisation appears to be a promising option. This implies that the material is to be processed in the semi-solid state; that is, at a temperature where a solid and a liquid phase co-exist. In the current paper, it is shown that zone melting can serve as an indi.cative test for assessing the refining potential of fractional crystallisation processes, since they are both based on the same thermodynamic principle. Next, the results of zone-melting experiments are presented for some representative aluminium model alloys. The BPS-model (developed by Burton, Prim and Stichter) is used to interpret these results, from which it is concluded that the model needs extension to obtain a predictive tool for fractional crystallisation processes.

Jan 1, 2000

By Nan Zhang, Gai-feng Xue, Shangchao Liu, Benquan Fu

"The high-magnetization microspheres of Fe3O4 encapsulated with S1O2 and T1O2 layers (Fe3O4@SiO2@TiO2) were prepared. The microspheres were characterized by transmission electron microscopy and scanning electron microscopy. These high-magnetization microspheres could be readily dispersed by shaking whereas they could be rapidly separated from the aqueous solution simply by applying an external magnetic field. The two shells of S1O2 and T1O2 protected the iron oxide well and the microspheres were stable in acid and base solutions. Therefore, they have a good potential for the enrichment of phosphopeptides or photocatalytic activity. They could also be used to remove metal ions from waste water.IntroductionSolid-phase extraction (SPE) is the most commonly used separation technique for its simplicity, consumption of small volumes of organic solvent, and the ability to achieve a higher enrichment factor. The quest for new adsorbents is an important factor in improving analytical sensitivity and precision in SPE techniques. To date, many novel adsorbents, such as nanometer-sized materials, carbon nanotubes, mesoporous materials and magnetic nanoparticles have been employed in SPE.Magnetic polymeric microspheres, an interesting advanced composite material, have received increasing attention in the past few decades because of their unique physical and chemical properties and their potential for use in applications in various fields [1]. Magnetic microspheres consisting of an iron oxide core and a silica shell have attracted particular attention for their unique magnetic response, low cytotoxicity, and chemically modifiable surface. The core-shell magnetic silica microspheres have shown great potential in the fields of biotechnology and biomedicine for applications such as cell labeling and separation, enzyme and protein separations, targeted drug delivery, and magnetic ferrofluids hyperthermia."

Jan 1, 2012

By K. A. Dudley

Basic solvent extraction theory indicates that pH initiates the basis of an oxime's metal complex formation and therefore its selectivity toward certain metal species. The recommended optimum pH for some of the commercial copper reagents is in a range that should maximise copper loading of the oxime. However, this pH range also tends to maximise iron(III) loading under certain operational conditions resulting in low selectivity values. Recent operational parameters at Girilambone Copper Company have highlighted some of these conditions that have a major influence on the oxime's selectivity for copper over iron(III) in the leach solutions. The result is that the pH for maximum copper extraction is no longer within the optimum range to maximise oxime selectivity. Therefore, specific copper and iron(III) pH isotherms have been determined on-site for the changing leach solutions that are fed to the solvent extraction plant in order to optimise oxime selectivity. The influences of solvent extraction plant configurations are also discussed as a controlling parameter.

Jan 1, 1999

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By M. J. Collins

A hydrometallurgical process has been tested at the Sherritt Research Centre for separation of zinc, lead, copper and precious metal values from the zinc oxide fume leach residue stockpiled at the HBM&S operations in Flin Flon, Manitoba. Zinc is found primarily as zinc femte and sphalerite in the residue, lead as lead sulphate and jarosite, and copper as sulphide and jarositic compounds. Gypsum and siliceous gangue are significant diluents. The separation process includes hot acid, atmospheric and reducing (sulphur dioxide) leaching; zinc, copper and lead flotation; and atmospheric iron removal steps. Zinc is recovered to a high strength zinc sulphate solution and to a zinc sulphide concentrate suitable for feed to a roaster or to a zinc pressure leach plant; lead to a high grade lead sulphate concentrate suitable for feed to a lead smelter, and copper to a high grade copper sulphide concentrate suitable for feed to a copper smelter. Precious metals are divided between the zinc, lead and copper concentrates.

Jan 1, 1993

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Xiang Ma, Halvor Dalaker, Kai Tang, Stefan Andersson

Silicon carbide (SiC) is one of the most important non-oxide ceramic materials for many industrial applications and is mainly synthesized by carbothermic reduction of silicon oxide by coke above 2200°C. Replacing natural gas (mostly methane, CH4) for coke in SiC synthesis could considerably reduce energy consumption and CO2-emissions owing to higher carbon activity of CH4 at lower temperature. The generally accepted reaction mechanism is that SiC is synthesized through gaseous intermediate silicon monoxide, SiO. In the present study, the reaction mechanism for the SiO and CH4 gaseous mixture has been examined using atomic scale modelling. Molecular dynamics (MD) using a reactive force field (ReaxFF) has been utilized to examine the initial stages of reactions involving a gas mixture of SiO and CH4 and surfaces of SiC. The MD results revealed some interesting SiC formation mechanisms. The reaction energies of the critical intermediate species were also estimated by density functional theory (DFT) calculations and the implications for the force field parameters used in ReaxFF was discussed.

Jan 1, 2015

A novel process is being developed for metal recovery from waste electrical and electronic equipment involving a leach reactor coupled to an electrochemical reactor. Metals such as Ag, Au, Cu, Pb, Pd, Sn etc. are dissolved from shredded electronic scrap in an acidic aqueous chloride electrolyte by oxidising them with aqueous dissolved chlorine species. In the electrochemical reactor: (i) chlorine is generated at the anode for use as the oxidant in the leach reactor, and, simultaneously, (ii) at the cathode, the dissolved metals are electrodeposited from the leach solution. The extended Butler-Volmer equation was used to provide predictions of the electrode potential dependences of partial current densities and, hence, total current densities, current efficiencies and alloy compositions for acidic aqueous chloride electrolytes containing Ag(I), Au(III), Cu(II), Pb(II), Pd(IV) and Sn(IV) species, together with dissolved chlorine. With judicious choice of kinetic parameters, the predicted total current density ? electrode potential behaviour of such solutions was in good agreement with experimental data for a rotating Pt disc electrode. Reduction of dissolved chlorine at a Pt rotating disc electrode exhibited mass transport controlled behaviour, in agreement with Levich?s equation over the potential range 0.3-0.9 V (SHE). This could form the basis of a linear sensor, possibly using a microelectrode for measurement and control of the dissolved chlorine concentration in the efflux of leach reactors and inlet to electrowinning reactors in the envisaged process.

Jan 1, 2003