Search Documents

By J. H. Puffer

The copper mineralization of the Mesozoic Passaic Formation of New Jersey is typical of copper deposits in eastern North American Mesozoic sediments. Most such deposits are located at the base of the first of several basalt flows that are interbedded with continental, red-bed sediments. The copper mineralization is similar in most respects to that of the Keweenawan Basalts of the Lake Superior area. The first basaltic flow units of the eastern North American Mesozoic basins, and the Keweenawan Basalts, are continental quartz tholeiites of similar chemical composition and copper contents. The copper minerals and associated zeolite facies metamorphic mineral assemblages of these two rock units are also approximately the same. Stoiber and Davidson (1959) suggested that Keweenawan copper was mobilized and concentrated during metamorphism. The evidence pertaining to the Mesozoic copper deposits of New Jersey is consistent with such an interpretation and also with DeVore's (1955) suggestion that ore fluids commonly arise as a result of the mobility of metals under metamorphic conditions. There is additional evidence that final metamorphic concentration of Mesozoic copper was preceded by an initial stage of hydrothermal precipitation related to fluids emitted by basaltic magma.

Jan 1, 1987

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005

By F. A. Myzenkov

The technology developed by the authors uses new methods for raw material smelting in electric furnaces, a new autogenous method and apparatus for subliming smelting for antimony trioxide production and separation of antimony and gold. Concentrate produced from the ore deposits in Yakutia has the following average contents of main constituents, % by weight: 29.4 Sb, 1.2 Fe, 13.1 S, 40.0 SiO2, 0.2 As, 2.6 CaO and 45 g/t of Au. Unlike the technology used abroad a new autogenous method makes it possible to increase considerably specific capacity and reduce gold losses with antimony trioxide by several times. At the same time mineralogical composition of trioxide has improved considerably ? it has mainly a cubic base with prevalence of senarmontite. The content of a main component (Sb2O3) in the final product has increased from 99.0% up to 99.6% which means better quality and makes it suitable for use in special technologies. Despite a lower antimony content of the concentrate (29.4% as compared with over 33% as common in the world practice), an antimony recovery of 85.3% into a commercial-grade product has been achieved, as well as a gold recovery of 96.65% into a gold-antimony alloy. The technology for processing gold-antimony materials developed and introduced at the Ryaztsvetmet plant is unique in the world with respect to gold recoveries.

Jan 1, 2006

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By T. Johnson, B. Q. Li

"Electromagnetic stirring has found a wide application in metals processing for the benefit of obtaining refined solidification microstructures. This paper presents an experimental study on the melt flow and turbulent behavior in an electromagnetically stirred Woods metal pool. The experimental setup consists of metal bath unit equipped with temperature control to allow both cooling and heating, velocity probe positioning unit and data and signal acquisition and processing unit. The whole measuring system is under the control of an IBM personal computer. Velocity measurements are made using the incorporated magnet probes, which are calibrated using a turntable. The measured results showing the effect of the coil positions, coil arrangements and the applied currents on the melt flow are presented. Both mean flow and turbulence quantities are discussed.1. IntroductionElectromagnetic stirring is widely practiced in the metals industry for melt mixing and for casting microstructure refinement. Industrial examples are taken from induction furnaces where the electromagnetic forces are applied to generate desired melt mixing and also various types of electromagnetic stirrers used in various stages of steel and/or aluminum casting processes to produce fine grain solidification microstructure or to eliminate undesired defects such as TCG (twinned-columnar-grain) structure. For ultrahigh purity aluminum or high strength aluminum alloys containing zirconium or lithium, grain refinement can be difficult with the conventional technique, and electromagnetic stirring provides a particularly powerful means to obtain the refined solidification microstructure [1]. A fundamental understanding of the melt flow and the turbulence characteristics in these magnetically-driven flow systems is of significant engineering importance to both process design and product quality improvement.There exists extensive literature on the magnetically-driven melt flows in material processing systems. Nakanish. et al. [2] were perhaps among the early investigators to mathematically and physically model the magnetically-driven flow phenomena in molten metal systems. Subsequent theoretical and experimental work by Tarapore and Evans [3, 4], Szekely and Chang [5], Hunt and Moore [6] and Szekely and El-Kaddah [7] has contributed very significantly to our understanding of magnetically-driven flow in inductively stirred melts. They have developed mathematical models for the electromagnetic field and turbulent flow in induction furnace and validated the models by either laboratory experiments or direct measurements in the industrial-scale induction furnaces."

Jan 1, 1998

By Du Sichen, S. Seetharaman, A. Jakobsson

"In the Present paper, the principles of oxygen potential measurements have been discussed along with the design details for oxygen sensors that are used in copper industry. A description of some of commercial probes is presented along with their salient features. The application of these sensors in flash smelting, converter and casting sections of copper production are discussed along with their implications on process optimization.I. IntroductionThe high temperature galvanic cells have come into prominence on account of their numerous applications in both fundamental as well as applied measurements. Since the inception of the oxygen-ion conducting electrolytes like ZrOrCaO·by Kiukkola and Wagner [1], the oxygen concentration cells have been extensively used in laboratories as well as in industries. In metal-production technology, these cells have been used to monitor the oxygen potentials in metallic, slag as well as gas phases and also to control and styr metallurgical processes. The pioneer among the various industrial users of such cells is the copper industry. To-day, high temperature solid electrolyte cells involving oxygen ion conducting electrolytes have become an integral part of copper pyro-refining and continuous casting. In the present paper some of the applications according to the industrial processes are described including the developments that are going on in the European scene."

Jan 1, 1997

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By B. S. -J. Kang, M. A. Alvin, J. M. Tannenbaum

"A load-based micro-indentation technique has been developed for damage assessment and non-destructive spallation detection of TBCs at room temperature. This micro-indentation technology has been further extended to the development of a high temperature (HT) test methodology. Elastic modulus calibration tests performed on Hl 3 Tool Steel to 500°C and Haynes 230 at 1000°C displayed excellent agreement with reported values. Moreover, indentation creep tests of Haynes 230 at 1200°C were found to be in agreement with known creep exponents as well. Finally, a HT thermal flux indentation apparatus was assembled for conducting TBC turbine component testing under high temperature moisture-containing environments (= 50% steam with controlled gas content temperatures up to 1250°C). Description and design considerations of this test apparatus are discussed. Preliminary tests of ReneN5/MCrAlY/APS TBC coupons in steam/air environments with in-situ HT micro-indentation testing are conducted. Furthermore, the coupon is removed and examined for damage assessment at periodical intervals.IntroductionLoad and depth relationships acquired throughout the indentation process provide insight to material mechanical properties such as elastic modulus and hardness. Unloading segment analysis of these load displacement curves are utilized in the acquisition of a material's elastic properties. Yet, indentation tests are complex processes involving contact mechanics, material nonlinearity and even fracture mechanics. Thus exact analytical solutions for these processes are difficult to obtain. As a result, much of the current knowledge regarding the indentation process has been acquired through experimental methods and finite element simulations. Initial efforts by Tabor resulted in the application of spherical indentation to obtain post-yielding stress/strain relationships [1]. Soon thereafter, analytical load-depth relations for elastic indentation were developed [2], yet it was Lure who further derived the explicit relationships for both spherical and conical indenters [3]. Improving upon this, these interactions were later extended to indenters with various geometries by various researchers [ 4]. Additionally, by establishing the linearity of the initial unloading slope within the load-depth curve, a relationship between elastic indentation depth, maximum load, unloading slope and indenter geometry was established [5]. From this a theoretical method by which elastic modulus could be determined was established."

Jan 1, 2011

By Milton Blander

"A review of concepts and theories for predicting thermodynamic solution properties of multicomponent high temperature liquid solutions is reviewed. During the last 50 years the ability to predict such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.INTRODUCTIONA number of solution theories and concepts have been developed which reliably predict the properties of multicomponent solutions from those of the lower order systems (often only the binaries). Because there is available data for a large fraction of the important binaries, the capability for making predictions for many multicomponent systems used in metallurgical separation processes is broad and potentially very useful. At the very least, the theories greatly minimize the data necessary for predicting properties of complex multicomponent solutions of molten salts, silicates and metals. It is the purpose of this paper to discuss the concepts which are demonstrably useful. We will discuss simple forms of the theories to make the concepts clear but we will refer to the publications which contain the more complex equations needed to treat the large majority of systems.A simple framework for understanding what we need to know in order to make technologically useful predictions is based on well known thermodynamic principles. In technologies and sciences where molten salts, slags magmas or molten metals are used or studied, one must often calculate the extent of a chemical reaction (or separation) or of phase changes. To do this, one must first write an equilibrium constant, K, for the reaction in terms of the standard free energy change of the reaction, ?G°."

Jan 1, 1996

By Vadim J. Jabotinski

This paper describes several areas of application for electron beam processing of materials. The technology and use of electron beam systems in gas phase synthesis reactions are described. Gas phase reactions may be used to generate ultra- fine metal or ceramic powder that are very pure and crystalline. Among the examples presented are: the generation of nanometer sized metal powders and the gas phase synthesis of silicon carbide for silica and methane. The experimental system is described and future theoretical and experimental objectives are identified.

Jan 1, 1998

By David Dreisinger

The pressure oxidation of pyrite is an important hydrometallurgical technology, especially in the total oxidation of refractory gold ores and concentrates (gold is locked in the pyrite structure preventing direct cyanide recovery). It has been noticed in some commercial applications and benchscale studies that the leaching of pyrite may be slow and apparently can be inhibited by the presence of molten elemental sulfur in the leach pulp. The purpose of this study was to determine whether Ortho-Phenylene-Diamine (OPD) could be used as a surfactant or dispersant for sulfur in the pressure oxidation of pyrite. OPD has previously been shown to be useful for pressure leaching of zinc and copper sulfides at 150 C.In this work, the interfacial chemistry of sulfur was studied at temperatures of up to 190 C in the presence and absence of OPD and other surfactants. The contact angle between molten sulfur and pyrite was also measured. Finally, the impact of OPD on the kinetics of pyrite oxidation was measured in bench-scale pressure oxidation experiments. The essential finding of this study was that OPD lowers the interfacial tension between molten sulfur and acid solutions and increases the contact angle (reduces wetting) between molten sulfur and pyrite. The work of adhesion between sulfur and pyrite was reduced by more than an order of magnitude in the presence of OPD. In bench scale tests, addition of OPD was found to significantly accelerate the rate of oxidation of pyrite. Conveniently, it was found that OPD was also fully degraded during high temperature oxidation processes. No residual OPD was detected in solution or solid samples from the leach testing. OPD is recommended as a sulfur dispersant in the pressure oxidation of pyrite and/or elemental sulfur containing feeds.

Jan 1, 2003

By Teruo Tanabe

The hydrogen-absorbing materials are expected to have the following properties at moderate conditions, (a) a large capacity of hydrogen absorption, (b) the absorption rate of hydrogen is large and (c) hydrogen-absorbed materials can easily desorb hydrogen. Thus the three concepts of capacity, rate and reversibility seem to be indispensable to clarify the mechanism of hydrogen absorption by the materials. In this work, the amount of absorbed hydrogen, the absorption rate and the reversibility of hydrogen absorption- desorption reaction were measured for binary R-M systems (R = Y, La, Ce; M = Co, Ni). These experimental results were discussed by the following three physical properties that were calculated by the extended Hückel method, i.e. the density of states unoccupied by electrons, the cohesive energy and the energy fluctuation. The major results are as follows: (a) the amount of absorbed hydrogen increases with the density of states in the energy range between -9 and -4 eV, (b) the R-M compounds of which energy fluctuations are large show a large value of rate of hydrogen absorption, and (c) when the cohesive energy is large, the compound has a tendency not to easily desorb hydrogen, i.e. its reversibility is poor.

Jan 1, 2006

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By M. G. Basavaraj, S. Sarkar, G. S. Gupta, P. D. Patil

"Previous experimental study on raceway size hysteresis on two-dimensional cold model showed that the inter-particle and wall-particle friction had a very large effect on the raceway size. Existing literature correlations for raceway size ignore the frictional effects. It has also been shown in the present study that their applicability to the ironmaking blast furnace is questionable. To take into account the effect of friction on the raceway size a stress analysis has been done for the raceway region. Two-dimensional fluid flow equations under turbulent conditions have been developed and solved computationally in order to get the pressure forces. The frictional forces were obtained in terms of stresses. To predict the raceway size a force balance was done for the raceway zone considering the pressure force, the frictional force and the bed weight. The resulting equations from the force balance are able to describe the raceway hysteresis phenomena reasonably well along with the raceway size. A two dimensional experimental set up has been fabricated in order to validate the computer predictions. Predicted values agree well with the experimental values.IntroductionWhen a high velocity blast of air is introduced into a packed bed through a tuyere, a cavity is formed in front of the tuyere. This cavity, formed in the iron-making blast furnace, is called the raceway. Coke tumbles down and bums in this raceway, generating heat and reducing gases for the iron-making process. The raceway is responsible for producing most of the reducing gasses in the blast furnace. In addition, the size and shape of the raceway determines the movement of solids within the blast furnace, the distribution of gases and liquids (slag and metal), setting the location where the primary chemical reactions occur and the temperature profile in the lower part of the blast furnace.Due to the importance of the raceway, many investigators l - 6 have studied it and have predicted the raceway size using the empirical correlations based on experimental (hot & cold) and mathematical models. A number of correlations have been reported in the literature to predict the raceway size by various investigators3 - 6 which are different to each other. Each of the correlations shows a different dependence of raceway diameter (DR) on bed height, particle size, solid density, bed voidage and blast velocity. None of the correlations includes the effect of solid stresses on the raceway size and shape. The magnitude of these stresses will depend on the bulk solids properties (internal angle of friction, wall angle of friction) and the bed dimensions."

Jan 1, 2001

By Gabrielle Gaustad

For aluminum, substitution of primary with secondary resources decreases energy consumption; this energy advantage creates a strong economic incentive to recycle. Several authors have raised concerns that the current sinks for secondary materials may soon be saturated, impeding subsequent expansion of recycling. This work combines dynamic material flow analysis with optimal batch planning models to quantify the significance and drivers of these pending limits under several scenarios, and thereby explore potential opportunities to increase recycling. An aluminum recycling system case was developed that includes containers and packaging, automotive, and construction products and scraps. The impacts on aggregate scrap utilization and materials cost are explored in the context of changing alloy demand and lifetime. Insights drawn from this specific case study could be applied to multi-stakeholder, systemic models.

Jan 1, 2010

By Jesús Contreras

Within its programme for continuous improvement and cultural change, Atlantic Copper has installed the Six Sigma methodology as a basic tool for the improvement of management techniques in all its production centres. Following an implementation period, the methodology is widely used for analysis and improvement, not only in the fields of production and maintenance, but also in other areas of the business such as supplies or energy management. The present paper describes, phase-by-phase, the project that was developed to improve the quality of converter slag through the application of Six Sigma techniques, from the initial set up to the final results obtained.

Jan 1, 2005