Search Documents

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Marco V. Ginatta

Current world production, 60'000 ton/y, is exceedingly too small for titanium's extraordinary combination of favorable properties; it should be 1,000,000 ton/y (7% of stainless-steel). Prices that competitively sustain that sales volume are achievable only with electrolytic production, as it is for all other commercial nonferrous metals. But titanium does not have its commercial electrolytic plants yet, because of producers decisions and strategies, scientists works, industrial problems with chloride process, lack of consumers sponsors. Fluoride high temperature process has the advantages of aluminum electrolysis, plus other favorable characteristics specific to titanium and its feed material. One electrolytic titanium potroom replaces several different plants used for sponge production. Production of titanium ingots with zero defect is achieved. The solidified cathode rectangular slabs are suitable for direct rolling.

Jan 1, 2001

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By E. Salinas R.

This work is related with a whole characterization of cantera stone, to establish its characteristics that can give it an additional value for the reuse and reutilization of dust, slurries and small pieces of stone which can be treated as wastes. The obtained results reflects that the residues studied can be used as substitutes of feldspars in the production of pieces of ceramic, and also in the elaboration of paints for the same pieces according to the mixes that can be made with the variation of Na2O, CaO and K2O. According to the humidity proofs and specific gravity done, this material can be proposed as a soil improver into hydroponics systems, leading so an important alternative for food production in zones leaking of water. In the same way, it was found the possibility of use this material as a seal 3A in processes of asphalting of roads, highways and streets.

Jan 1, 2009

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Lauri E. K. Holappa

The aim of the metallurgical process development is, nowadays, to search for the shortest, most economical, more environmentally friendly and sustainable route to convert raw materials to finished products. Recent progress in steelmaking processes ? BOF and EAF - has also motivated to search for more advanced casting technologies to shorten process route. Continuous casting, which became industrially feasible in the 1960s, is now a mainstream technology with over 90% share of the world steel casting. After the 1980s, the increase in steel production and consumption, particularly from automobile, construction and home appliances industries, required steel manufacturers to accelerate production with more concise procedures, so that near-net-shape casting took the trend of development in order to bypass and simplify the downstream processes, e.g. cold/hot rolling mill or extrusion mill, to directly obtain finished products with required geometries. Progress in flat and long products changed the industrial operation pattern, strengthened steel production efficiency, and formed the operation concepts of the integrated steelworks and mini-mills, respectively. Thin slab casting and strip casting have represented the most important progress and promise, in the recent years, of such innovations furthermore strengthening the production efficiency and, concurrently, coinciding with the demands of environmental protection and sustainability. This paper reviews the most recent progresses in near-net-shape casting and prospects the impacts to steel industries as well as the development trends of steel production, in general.

Jan 1, 2006

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By N. Tsuneyama

Sumitomo Metal Mining Company has been operating Waelz Kiln at the Shisaka Works for 12 years to recover zinc and lead from electric arc furnace (EAF) dust. To increase the capacity and cut down the operating cost, some improvements have been carried out resulting in the capacity of 60,000 t/ y of EAF dust as compared with 32,000 t/ y in 1977. The current capacity is equivalent to 20% or EAF dust generated in Japan. The number of workers has been decreased by the introduction of an automatic control system, and the productivity per worker is now twice as much as 10 years ago. This paper will describe the progress of the operation at the Shisaka Works after the previous? paper reported in "Zinc&apos; 8 5? and summarize the status or EAF dust recycle in Japan.

Jan 1, 1990

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental&apos;s Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960&apos;s. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By R. C. Hubli

A chemical model has been developed to investigate the dissolution of sulphide minerals in brine solutions containing copper and iron chlorides. The model has been employed to study the dissolution .of synthetic NiS using different initial concentrations of Cu(II), Cu(I), Fe(III) and temperature. The speciation of copper with particular reference to the formation of hydroxy-chlorides as a function of total chloride and H+ has been computed. The model predictions are in agreement with experimental results. It has been found that addition of Fe(III) results in the maintenance of a high Cu(II)/Cu(I) ratio leading to enhanced rates of dissolution and suppresses the loss of Cu(II) due to the formation of hydroxyl-complexes.

Jan 1, 1997

By Zhang Hanbo, Niu Liping, Zhang Zhiqi, He Jicheng, Dou Zhihe

"Rutile, ilmenite and Al-Ca complex reducer were used to prepare high titanium ferrous alloy by enhanced reduction-SHS method. The effects of the complex reducer compositions and slag types on the enhanced reduction-SHS process were investigated. The high titanium ferrous alloys were characterized by XRD and SEM. The results indicate that the high titanium ferrous alloys consist mainly of TiFe2, AlTi3 and Al2O3. The oxide inclusions exist resulting in directly the high oxygen content and micro-structural defects in the alloys. The titanium and oxygen contents decrease, but the aluminum content in the alloy increases while the mass ratio of calcium in the Al-Ca complex reducers increases. When the mass ratio of Al/Ca in the Al-Ca complex reducer is 6:1, titanium, oxygen and aluminum contents are 63.75%, 3.01% and 10.72% respectively. When the mass ratio of Al/Ca is 5:1 titanium content is 55.00% nearly and aluminum content is higher than 14.00%, but oxygen content is lower than 2.0%.1. IntroductionThe high titanium ferroalloys with 65%~75% titanium have the advantages of low melting point and high titanium content. They are widely used in special steel refining, while they are also a kind of very important quality orientation alloys in the rage of aviation and aerospace. At present, the methods of preparing high titanium ferroalloy include vacuum remelting and thermit reduction. The alloys prepared by the vacuum remelting method have good qualities and low oxygen content, so it is widely used in Russia, Western Europe and other developed countries. In China, there are abundant rutile resources, but waste titanium is lack, therefore, the preparation method is the thermit reduction. But there are many quality defects in the high ferrotitanium alloy, including high oxygen content, unstable quality and so on. In order to improve the qualities of the high titanium ferroalloy, especially to reduce oxygen content, the domestic and overseas have done a lot of further researches. For example, Sichuan E-mei ferroalloy plant and Beijing Nonferrous Metal Research Institute have prepared high titanium ferrous with 73.77% titanium with natural rutile, but the oxygen content is high. Through controlling the quality of raw material, they obtained the better qualities, but the oxygen content is still very high. South Africa Mintek company have prepared high titanium ferrous alloy with low nitrate by plasma heating under the isolation air conditions, but they couldn’t also remove effectively oxygen in the alloy. The oxygen exists in the form of Al2O3 and titanium protoxide. So it can be speculated that except TiO2 not being fully reduced, the no-sufficient alloy-slag separation is the direct reason resulting in high oxygen and poor microstructure. In view of present technical difficulties during preparing high titanium ferroalloy by thermit reduction, this paper proposed a new method of preparing high titanium ferrous with low oxygen by enhanced reduction-SHS with Al-Ca complex reducer. Ca in Al-Ca complex reducer has stronger reductive ability, it can effectively strengthen the reductive degree of TiO2. The slagging agent CaO CaF2 and MgO can effectively reduce the viscosity of Al2O3 slag to improve its liquidities to strengthen alloy-slag separation effects so that to remove inclusions and oxygen. In this paper, effects of slagging agent type on the reduction and the qualities of high-titanium ferroalloy were studied."

Jan 1, 2012

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By Cesar Garban

The samples of the washings are characterized of the ore for physical, chemical and metalurgical properties for representivity. the optimum values are determined for the recuperation of gold of the washings of the gold ore from the zone El Callao, Venezuela by acidic solutions of thiourea of the following parameters: Ph , contact time, composition of the liquid mixture, ratio of solid to liquid, grade of liberation, in an apparatus designed for contacting solid powder of the mineral with liquid solution of thiourea mantained in suspension by bubles of compressed air. The experimental results showed that the velocity of lixivation in primier time of (20) minutes is rapid and practically 2/3 part of the reaction is completed. For experimental design of parameters, the optimum conditions of recuperation of gold determind in this experimental investigation are:

Jan 1, 1999

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By Jason Eric Sallee

Ongoing operations at the Cyprus Miami Smelter involve the use of an electric furnace for settling of copper matte from discard slag. Proper operation of the electric settling furnace is a major factor in minimizing losses of copper to the discard slag. Recent test work at the smelter has shown improvement in the operation of the electric furnace with a subsequent improvement with regard to the copper losses. This paper presents a general discussion of the Cyprus Miami Smelter operation, past results with respect to copper losses, recent operational changes and test work, and the subsequent results.

Jan 1, 1999

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011