Search Documents

By M. R. Dahm

The demand for low sulfur steel by steel manufacturers and their customers has been steadily increasing for 25 years. Historically sulfur has been controlled by various means and with various additives but lime-magnesium external desulfurization of hot metal has become established as the dominant method in North America today. Magnesium powder produced from primary magnesium ingot has been the major source or raw material. However, periodic increases in the price of this commodity have encouraged producers to look to secondary magnesium for an alternate source of magnesium. Secondary magnesium from post-consumer scrap can be cleaned, sized, and prepared to produce a high quality magnesium reagent for use in hot metal desulfurization at a lower cost than material processed from primary ingot.

Jan 1, 2000

By O. Kitamura, H. Kubota

The Harima Works started its ISP operation in 1966 and been expanding its production capacity from 3,000 tonne Zn/month and 1,500 tonne Pb/month to 7,500 tonne Zn/month and 2,500 tonne Pb/month. It is not only treating zinc, lead and bulk concentrates but also secondary materials like Waelz kiln oxide from the Shisaka Works of Sumitomo Metal Mining, waste treatment sludges, industrial wastes and others. Its final products cover Prime Western Grade (PWG) zinc, Special High Grade (SHG) zinc, continuous galvanizing grade zinc, electrolytic lead, cadmium, indium, thallium and sulfuric acid. This paper briefly describes the smelter's historical and present operations. The key data for the current impurity control management and for the distribution of impurities such as copper, iron and arsenic are presented.

Jan 1, 2000

By Kazuki Morita

A new route to produce solar grade silicon (SOG-Si 6N) from metallurgical grade (MG-Si 98%) has been developed in Japan, which may satisfy the increasing demand for solar cells in the near future. Since some elements such as P and B have very large segregation coefficients, solidification refining is not effective for their removal and costly processes, such as electron beam vacuum melting and oxidation plasma refining, are required. According to our previous results which showed the effectiveness of leaching procedure with Ca addition for Fe and Ti removal, possibility of P and B removal by acid leaching was focused expecting that their affinities for Ca in molten silicon might be considerable. Hence, the effects of Ca addition on the thennodynamic properties of P and B in molten silicon alloys have been investigated for overall control and optimization of the SOG-Si production process in the present study. The interaction parameters between Ca and P, and Ca and B were determined by chemical equilibration techniques at 1723 K. Although the interaction parameter between Ca and B was slightly negative, that between Ca and P showed a large negative value. Also, the results for the leaching test with various amount of Ca addition revealed that the removal fractions of both elements, especially P, drastically increased with increase in the Ca content, which showed very good agreement with the prediction from the interaction parameters derived in the present work. The present results suggest that the preliminary leaching procedure can reduce the processing time and energy for SOG-Si refining. Keywords: Silicon, Solar Cell, Refining, Acid Leaching, Thennodynamics. Interaction, Phosphorus, Boron, Calcium

Jan 1, 2003

By Stanko Nikolic

Ferrous calcium silicate slags are potentially important for future practice in copper converting operations and processes and can be described by the ?Cu2O?-FeO-Fe2O3-CaO-SiO2 system. Despite its industrial importance the phase equilibria in this system have not been fully investigated. Characterization of this slag system is necessary to improve the design and optimization parameters of new processes, including fluxing and operating temperatures. Experimental methods have been developed to investigate the phase equilibria of these slags at copper saturation and without copper. This technique involved equilibration of samples at a fixed oxygen partial pressure, rapid quenching, and analysis of the compositions of phases using electron probe x-ray microanalysis (EPMA). Liquidus and solidus data are reported for the primary phase fields of spinel, wollastonite and tridymite at 1250oC and an oxygen partial pressure of 10-6atm. The resulting data has been used to construct liquidus isotherms in the ?FeO?-CaO-SiO2 system both in equilibrium with and without molten copper. The experimental results were compared with the predictions of a thermodynamic computer package utilizing a self consistent thermodynamic database. The predictions of the model were in good agreement with the experimental isotherms when projected onto the FeO-CaO-SiO2 section, however the copper concentrations in the liquid phase at copper saturation were lower than predicted using the current database of the model.

Jan 1, 2006

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By A. McLean, Y. Uchida, M. Iwase, M. Myochin, K. Wiikimoto

"Phase diagrams of FeO-containing ternary systems could be derived from experimental data for the activities of FeO. The systems investigated are CaO-CaF2-FeO, SrO-SrF2-FeO; BaO-BaF2-FeO, CaO-CaCl2-FeO, SrO-SrC12-FeO, BaO-BaC12-FeO, CaO-A12O3-FeO and BaO-SiO2-FeO.IntroductionThe importance of phase diagram cannot be overemphasized. In a book, ""Alloy Phase Equilibria""[l], the author, Professor A Prince, states, ""A metallurgist has been defined as a person who thinks in terms of phase diagram"". Whether one accepts this statement or not, it is self-evident that an ability to interpret phase equilibria is essential to the professional metallurgists.The physical chemistry studies of iron and steelmaking process often require phase diagrams of FeO-containing slags. Iso-thermal section of the phase· diagrams of such systems can be derived from experimental data for chemical potentials of FeO. Due to the recent developments in the area of solid state electrochemistry, rapid determinations of the FeO activities have become possible. The present paper is aimed at documenting the derivation of the phase diagrams of FeO containing slags.Experimental AspectsAn electrochemical method incorporating stabilized zirconia can be used for the measurements of the activities of FeO in various slags and fluxes[2]. For the details of the experimental technique, reference should be made to reference 2"

Jan 1, 2000

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By Rauf Hurman Eric

The high temperature liquid miscibility gap in the Ag-Ag2S pseudobinary portion of the Ag-S system has been redetermined by very carefully conducted equilibration-quenching experiments. Samples were contained in evacuated and sealed silica capsules. The stratified liquid phase compositions were obtained by chemical analysis. The miscibility gap extends from 14 to 32.3 atomic percent at the monotectic temperature of 906°C and closes at around 1320°C.Thermodynamic properties of the liquid solutions, including the limiting activity coefficient of sulfur in molten silver were expressed analytically by using the sub-regular solution model which proved to be in excellent agreement with the experimental findings.

Jan 1, 2006

By P. Barrios

The copper refinery of Atlantic Copper was modernised and converted to the Isa permanent cathode system in 1995. The technology installed has proved to be an excellent platform for the development of operational improvements. During the years it has been working, the progressive assimilation of the new technology has been achieved and the level of operator knowledge has allowed design production to be reached and surpassed by more than 10%. At the same time, modifications to the work programmes, using existing equipment, have permitted the incorporation of new cells and the achievement of annual production levels of 250,000 tonnes and a productivity of 0.43 t/man-hour.

Jan 1, 1999

By Tianzu Yang, Weifeng Liu, Lin Chen, Qingkai Xiao, DUCHAO ZHANG

To solve the problem of low leaching ratio of direct gold cyanide leaching from arsenical refractory gold concentrate, this paper proposed a matte smelting process for gold enrichment in low grade copper matte. The effects of copper content in the mixed material, ratio change in slag type, smelting temperature and reaction time on recovery rate of gold and copper were investigated. The experimental results indicated that the recovery rate of gold increased with the increase of copper content in the mixed materials, temperature and reaction time. It was also noted that the recovery rate of gold and copper were respectively 98.16% and 96.39% when the addition of copper content in the mixed material was 3%, slag type of CaO/SiO2 and FeO/SiO2 were 0.6 and 0.9 in 1250°C and the time of reaction was 40min. Most of the arsenic was oxidized into As2O3 existed in the dust. The results showed that the matte smelting method can achieve efficient recovery of gold from arsenical refractory gold concentrate.

Jan 1, 2016

By Simon Lekakh

Direct reduction of Cu,Ni,W,VandMo oxides from various industrial wastes the melting of iron and steel in different furnaces was studied by thermodynamic computation and experimental methods. Thermodynamics was used to compute the final partition of the alloying additions between iron-carbon melts and oxides contained in the slag. It was shown that the sequence of the reduction reactions depended on the melt composition as well as temperature. Kinetic factors limited recovery in induction melting, while experimentally measured final partition coefficients were close to equilibrium during EAF melting. The possibility of the partial substitution of expensive ferroalloys, by different industrial wastes containing nonferrous oxides, was evaluated in foundry and mini-mill conditions.

Jan 1, 2006

By Yuhua Pan

Generic mathematical models have been developed for simulating heat transfer in two types of slag resistance heating electric furnaces for sulphide smelting: i) six-electrode-in-line rectangular furnaces and ii) three-electrode circular furnaces. The models are based on three-dimensional steady-state heat transfer of conduction, convection and radiation. Solidification of liquid slag into solid slag by water-cooling units, for use as freeze lining of furnace walls, is also considered in the models. The developed models are capable of providing predictions with reasonable accuracy for electric furnaces on 1) temperatures in slag, matte, cooling water, freeze lining and other solid regions as well as temperatures at various fluid/solid interfaces, 2) freeze lining thickness, 3) furnace smelting rate and 4) furnace heat loss rate. These computer models are built into executable application programs that are very efficient, with execution time less than one second, and can be easily portable to most computing platforms. This paper describes, as an example, the modelling results on heat transfer in six-electrode furnaces. The major modelling results show that in six-electrode furnaces uniform electric power inputs to the electrodes likely lead to low temperature regions close to slag and matte tapping ends of the furnaces, and the power input and the formation of air gaps between freeze lining and cooling units have significant influences on the thickness of freeze lining maintained by the cooling units.

Jan 1, 2006

By F. M. Nakla

Various methods of Applied Mineralogy were used for determining the nature and composition of products yielded by flotation tests for Maghara coal beneficiation. Coal samples obtained from the Sa fa mine in Northern Sinai, Egypt, were crushed, sieved, &apos;and <32 mesh size fraction was cleaned by froth flotation. Experiments were conducted to determine the effect of certain parameters on beneficiation of Maghara coal by flotation. The investigated factors included nature of frothing and/or collecting reagents, pH value of the medium, particle size distribution in the head sample, and pulp density of the coal slurry. The quality of head samples, coal concentrates, and tailing products were determined by chemical analysis, microscopic study, x-ray diffraction analysis, and occasionally by infrared (IR) absorption spectroscopy.

Jan 1, 1989

By Shengli Wu, Jinming Zhu, Wei Huang, Xinliang Liu

The sinter of high basicity would interact with lump ores or acid pellets in the cohesive zone of blast furnace due to the difference of chemical composition and micro structures. The results of this work showed that the softening-melting properties of lump ores and acid pellet would be obviously improved by the high temperature interaction. However, the high temperature interaction index (INI) would be influenced by many factors, such as chemical composition, porosity, interaction interface and so on. The INI between sinter and porous limonite lump ore (L-2) was much higher than that of dense hematite lump ore (L-1) and acid pellet (P-1). In addition, though the softening and melting properties of L-2 were poorest in respective iron ores, the softening and melting properties of integrated burden B (consist of sinter and L-2) were not worse than other integrated burdens due to the strong high temperature interaction.

Jan 1, 2015

By Taner Kavas

In the present study the utilization of coal ashes that appear at the end of firing process of brick production in cement pastes was examined. Ashes with three different particle sizes of 75 µm, 106 µm and 150 µm were used to replace ordinary Portland cement (PC) as 5 % and 15 % by weight. Seven samples were prepared and physical, mechanical, chemical and microstructural analyses were carried out. The compressive and bending strength values of samples were determined at the ages of 2, 7 and 28 days. It was found that cementitious pastes with finer particle sizes possessed the highest compressive and bending strength values at all curing ages. Both values after 2 and 7 days cure increased with an increase in ash content, no matter what the particle sizes of ashes were. However, strength decreased after 28 days cure as a result of ash addition of 15 %, although it was still above that of the PC.

Jan 1, 2006