Search Documents

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By Dao Su, Ganghua Fu, Xuling Chen, Yufeng Guo, Min Gan, Tao Jiang, Xiaohui Fan

"The sinter quantity and quality of limonite in the magnetite and hematite sintering models were studied and compared. For the sintering of magnetite, the results showed that the increase of limonite improved the permeability of sinter mixture, increased the sinter quantity and quality. The sinter strength and productivity were decreased when the proportion of limonite exceeded 50%. The appropriate proportion of limonite was 40%-50%. For the sintering of hematite, the sinter quantity and quality were first maintained at the same level thereafter declined, more obviously when the proportion of limonite exceeded 40%. The amount of calcium ferrite increased whose shape changed from acicular to leaflike and block gradually with the proportion of limonite increased from 0% to 80%.IntroductionWith the fierce competition of domestic and overseas iron markets in the twenty-first century, cheap ores such as limonite are used to be sintering raw materials to cut the costs of sinter and pig iron for steel making, and boosts the competitiveness of steel companies [1, 2]. In addition, as the reserve volume of hematite of high grade is reducing year by year, the usage amount of limonite in sintering are expanding in major domestic and international sintering plant [3, 4]. Sintering can be divided into two types, majoring in concentrates and fine ores, according to the different types of raw materials. The sintering characteristics of limonite in the two types above have been studied and compared in this paper, which makes a significant sense for the research of limonite sintering properties and guidance of ore proportioning in sintering plants."

Jan 1, 2012

By Daniel A. Norrgran

Grinding ball fragments discharging from SAG mills and ball mills causes extreme wear to downstream processing equipment. These ball fragments, recirculating in a milling circuit, will cause excessive wear to sumps, pumps, hydrocyclones, and interconnecting piping. A magnetic separation system to remove grinding ball fragments from the mill discharge has been developed and successfully applied in the milling circuit. This magnetic separation system - termed Trammel Magnet - was first applied at the Escondida copper concentrator in Chile. The Trommel Magnet consists of an arc of permanent magnets mounted at the discharge end' of the tommel screen. The magnetic arc attracts the ball fragments and removes them from the process stream. This retrofitted magnetic separation system removed 126 metric tons of ball fragments from the circulating load of a. single ball mill in the initial 24 hour period. The mill has since stabilized and the magnetic separator is currently removing 7 metric tons per day of ball fragments. The retrofit of the Trommel Magnet has: 1. Extended the pumpp life and the hydrocyclone life approximately 300 percent. 2. Provided a 5 percent increase in the throughput of the mills by removing grinding ball fragments that contribute very little to the grinding process. Variations of the Trommel Magnet have also been developed for removing grinding ball fragments directly from the mill discharge without the use of a trommel screen. In each case, permanent magnets are used to collect the ball fragments from the mill discharge stream prior to reporting to the sump. These other systems have been designed and fabricated for in-plant test work.

Jan 1, 1999

By A. Slotwinski, R. E. Barry, M. M. Menon, P. T. Spampinato

"A coherent FM laser radar based sensor for remote metrology of plasma facing material surfaces in a fusion reactor is described. The sensor is capable of 3-D mapping of surfaces, based on a series of precise range measurements from large distances (up to 20 m). Other features include the ability to operate under adverse environmental conditions involving very high gamma radiation (3xI04 Gy/hr), ultra-high-vacuum (<I0-5 Pa), and high temperature (200°C). The paper describes the basic principles of the sensor, together with experimental results obtained with the sensor. The ability of the sensor for remote rendering of ""visual quality"" images without the need for any external illumination is also illustrated.IntroductionMeasurement of the features of large area surfaces (-1500 m2) to sub-millimeter accuracy, from relatively large distances (20 m), is necessary in the case of the International Thermonuclear Experimental Reactor (ITER -a 1500 MW fusion reactor that is currently in the design phase). Furthermore, the measurements may have to be performed after the reactor is temporarily shut down. During such shut-downs, the ITER in-vessel environment will be highly radioactive due to neutron activation of the reactor wall (gamma radiation field of 3xl04 Gy/hr), the vessel will be maintained under ultra-clean vacuum conditions (<10-5 Pa), and the plasma facing surfaces will be maintained at elevated temperature (200°C). Therefore, the precision measurements must be conducted remotely, and because of the large dimensions of the fusion reactor and the limited number of access ports, the measurements must be done from large distances. The reactor vessel is a large toroid. Fig. 1 shows the cross section of the toroidal vacuum vessel, and the location of the metrology probe. Because of the very large surface area involved, fast scanning capability is also needed to reduce the reactor down-time."

Jan 1, 1997

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011

By Laurentiu Nastac, Ruslan Mudryy

"This paper investigates the solidification of cast energetic materials. An active cooling and heating (ACH) technology and a mechanical vibration (MV) technology were applied to achieve unidirectional solidification during casting and to reduce cracks, gas pores, and shrinkage defects. The design parameters of these technologies were developed via Computational Fluid Dynamics (CFD) modeling and thermal stress analysis. Concerning the ACH technology, the number of cooling/heating sections and their temperature profiles and time sequences were optimized based on the thermo-physical properties of the energetic material as well as the riser and mold diameter, thickness and type. The ACH technology will also decrease the thermal stresses during casting of energetic materials and therefore minimize the formation of potential cracks that may form during the casting process. The MV technology will help to remove air entrapped during pouring process and decrease the detrimental gap size between the projectile and the solidified energetic material.IntroductionCasting processes are widely employed in the manufacture of products with intricate shapes and, in particular, in applications where the material of the final product is sensitive to machining. It is especially useful in processing of energetic materials. The cooling conditions applied in the casting process can affect the quality of the final cast in terms of void formation, residual stress distributions, and mold separation. Substantial shrinkage is also observed due to the density change upon solidification [1-3]. Residual stresses are known to be closely related to the formation of cold cracks and hot tears during casting. The formation of a gap between the mold and the cast material is of critical importance due to its deleterious effect on heat removal and on crack formation. In the casting of energetic materials all these defects can significantly impair the detonation velocity, Gurney energy, and insensitive munitions characteristics of the formulation, and lead to catastrophic accidents in explosives handling [ 4-5]. Imposition of carefully controlled cooling condition is thus critical in optimizing the cast quality that could help avoid such destructive effects."

Jan 1, 2013

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By P. S. Dunn, A. D. Rollett, H. D. Lewis

"The results of preliminary work on the modeling and measurement of the heat transfer coefficients of metal/mold interfaces is reported. The system investigated is the casting of uranium in graphite molds. The motivation for the work is primarily to improve the accuracy of process modeling of prototype mold designs at the Los Alamos Foundry. The evolution in design of a suitable mold for unidirectional solidification is described, illustrating the value of simulating mold designs prior to use. Experiment indicated a heat transfer coefficient of 2 kW/m /K both with and without superheat. It was possible to distinguish between solidification due to the mold and that due to radiative heat loss. This permitted an experimental estimate of the emissivity, ~ = 0.2, of the solidified metal.IntroductionA feature that distinguishes casting processes from welding processes is the presence of an interface with a low heat transfer coefficient between the mold and the casting. Especially when chill casting, the interface delays the start of solidification and increases freezing times significantly. By comparison welds can be assumed to have a very high heat transfer coefficient. The heat transfer coefficient controls such phenomena as folds and laps on the surface of castings which can be crucial to the acceptability of a casting. The time delay for the start of solidification influences the occurrence of cold shut defects. The standard mold material for uranium casting is high quality graphite which is an excellent refractory when used in vacuum and coated with a refractory wash. Graphite is an effective chill material and has a thermal diffusivity approximately twice that of uranium. Experience has shown that practicable superheat without mold pre-heat is not sufficient for avoiding cold shut defects when casting in graphite molds.TheoryIt is possible to calculate the position of the freeze front s, as a function of time, t, the superheat and interface heat transfer coefficient, h, [1]. However, the value of h cannot be obtained explicitly. The Virtual Adjunct Method (VAM) [2] offers a method for extending the standard equation for an insulating mold where s is proportional to the square root of time. By considering the effect of the interface to be equivalent to finite thicknesses of mold and metal, the following quadratic equation is obtained,"

Jan 1, 1986

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from Copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu10), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, Cu2O bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties of the CaO-FeOX-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation. -

Jan 1, 2003

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By Yong J. Kim, J. M. Park

"Solid/melt interface shape during continuous casting process has a strong influence on the resulting microstructure of the ingot. The interface shape is primarily governed by the heat flow condition between the molten metal and mold (or container). The roll of the microstructural transition resulting from various solid/melt interface shapes is discussed using the Sn-22.6wt%Pb alloy. Three different types of mold such as cold mold, resistantly heated mold, and electromagnetically heated mold were used to generate those interfaces having different curvatures. Experimental measurements of complete temperature profile along the axis and surface of the ingot during downward continuous casting are presented to determine the solid/melt interface geometry. The results provide an explanation of the ingot property with emphasis on microstructure.IntroductionA large scale of continuous casting process of alloys often has a rather deep V channel type of solid/melt interface resulting from a limited heat flow condition. As a result, the deep V type solid/melt interface shape entraps defects such as pores and inclusions and also creates canter segregation. In order to reduce the defects concentration, electromagnetic stirring(EMS) mechanism has been applied to the melt in the channel[l]. Speith and Bungeroth introduced first experimental EMS device to the continuous caster in 1952.[2] Today, with wide ranges of benefit, a large variety of such technique is available. Electromagnetic field on the melt can be divided into three aspects. First, eddy current is induced on the metal surface by alternating magnetic field with high frequency, which results in heating the metal. Second, electromagnetic body force which is generated by the magnetic field and the eddy current reduces the melt pressure on mold or support the melt not to contact with the mold[3,4,5]. This force is used for electromagnetic casting process(EMC). Finally, it causes stirring in the melt. Many research efforts have been done on the EMC process to improve surface quality of slab[6] and control meniscus shape where three phases such as melt, solidified metal, and mold powder coexist[7,8]. However, the eddy current heating effect on the surface of the ingot was less considered. It is worth noting that induced eddy current on the surface of slab melts the solidified shell and thus changes the heat flow condition between the mold and melt. Mold heating effect was first proposed by A. Ohno[9] and its processing conditions were identified in details[ 10, 11]. The so-called Ohno process is based on the fact that by keeping the mold temperature slightly above the melting temperature of the liquid, no grain can be nucleated on the mold wall[12]."

Jan 1, 1998

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from &apos;the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Peter K. Liaw, Charlie R. Brooks, David C. Joy, Wei Zhao

In this paper, effects of oxidation, porosity and fiber-fabric stacking sequence on flexural strength of a continuous silicon carbide fiber (SiCr) fabric-reinforced SiC ceramic-matrix composite (CFCC) were studied. The failure mechanisms were correlated with flexural strengths of CFCC samples, both before and after oxidation. Microstructures and fractography were investigated using scanning electron microscopy (SEM). The chemical change after oxidation, such as Si, C, and 0, and their distributions, were detected by the SEM energy-dispersive X-ray spectroscopy (EDXS) line-scan chemical analysis technique. These effects on the strength of the CFCC can be attributed to following reasons: (i) The decrease in the flexural strength after oxidation is mainly due to degradation of the strength of Nicalon fibers and the damage of fiber/matrix interface both caused by high-temperature chemical reactions, (ii) Porosity is not too important in affecting the strength of the CFCC, when the bonding of the forced flow chemical vapor infiltration (FCVI)-SiC matrix is stronger than that of the fiber/matrix interface. However, a higher porosity content will be harmful, because higher porosity will both decrease the effective elastic modulus of the FCVI-SiC and make pore-linkage easier to occur, which is more likely to cause premature failure, (iii) The variation in the lamina stacking sequence of the CFCC changes the elastic stress distributions along the thickness direction of specimens, the magnitude of ceramic matrix-cracking stress, the effective elastic moduli of the laminate, and different crack initiation sites as well as different failure modes, and thus, leading to the scatter in the flexural strength of the CFCC.

Jan 1, 1998

By Noriaki Kurita, Norihiko Fulcatsu, Teruo Ohashi

"An electrochemical sensing device for hydrogen in molten metal has now been available owing to the development of the proton conducting solid electrolyte made of ceramics of metal oxide. The structure of the sensor and the theoretical limitations of its applications are discussed based on the electrochemical properties of the electrolyte used. The practical performance of the sensor is reviewed from the results of test measurements at the plants of aluminum and copper melting industries. The effectiveness of the sensor to the process control of continuous casting of copper is also discussed.IntroductionSince the in-line monitoring of the amount of oxygen dissolved in molten metal was realized by using the oxygen concentration cell based on zirconia solid electrolyte a similar method has been expected to be developed for sensing of hydrogen, which is a very important element of gas species in liquid metals, especially, in aluminum and copper. In 1981; Iwahara and coworkers found the dominant proton conduction at a high temperature in some perovskite-type oxide (1). Since then, the effort has been made to apply this proton conducting material as the electrolyte of the hydrogen concentration cell for high temperature use. The hydrogen sensor for liquid aluminum of this kind was first produced in 1991 (2) and released commercially from TYK Co., Ltd. Recently, we have developed the mother one usable at higher temperature such as copper and silver melting processes (3). In this note we discuss their structure, design and applicable limitations based on the electrochemical properties of this new type electrolyte. The performance of the sensor and benefit to use it to control the melting process is also discussed"

Jan 1, 2000

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By H. Conrad, K. Jung

"The effect of an external electric field E=5(+) kV/cm applied during the solution heat treatment at 500°-550°C of three commercial Al-Mg-Si alloys (AA6061, AA6022 and AA61l1) on the asquenched resistivity Pw and hardness H.,NULL, w was investigated. It was found that the field gave a significant increase in Pw and in Hv,w, for AA6022 and AA6111, but had no clear effect on AA6061. Thermodynamic analysis gave that the effect of the field on AA6022 and AA6111 was to reduce both the enthalpy ?H, and entropy ?H, of solution. Considering the chemical composition of the three alloys it appears that the influence of the field may depend on the amount of Cu plus excess Si present in the alloy.IntroductionKlypin and Soloviev [1, 2] were the first to report that the application of an external electric field during solution heat treatment (SHT) of Al alloys gave an increase in the as-quenched resistivity and hardness. They attributed these effects of the field to an increase in solubility of the alloying constituents during the SHT. More recently Liu and coworkers [3, 4] also reported an increase in the as-quenched resistivity of Al-Li alloys with application of an electric field during SHT. Further, the present authors [5] found that the application of an electric field during the SHT of the commercial Al-Mg-Si alloys AA6022 and AA61i1 increased their as-quenched resistivity and hardness. Their thermodynamic analysis of the results indicated that the field decreased both the enthalpy ?H, and entropy ?S, of solution."

Jan 1, 2004

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005