Search Documents

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Alexander A. Knminskii

Polymorphism of BaR2F8 compounds is analyzed, and some peculiarities of obtaining monoclinic low-temperature (3-BaR2F8 crystals (R=Y, Ho-Yb) and orthorhombic high¬temperature a-ßaR2F8 crystals (R=Yb, Lu) by the Bridgman-Stockbarger growth technique are discussed. We pay a special attention to BaYb2F8:Er3+ crystals, which are able to generate both 2:µm SE using the new four-level operating scheme (4F9/2?4I11/2 laser channel) and 2- and 3-µm SE by means of the cascade scheme (4F92?+4I11/2?+4I31/2). This 2-µm generation of Er3+ ions has an advantage over similar SE of Ho3+ and Tm3+ ions (especially under diode laser pumping), that is important in designing the medicine and ecology laser. We report on orthorhombic BaR2F8 crystals with the ordered structure, a new crystalline materials for generating Ln3+ ions. The growth conditions are determined and orthorhombic BaLu2F8 crystals of several cm3 in volume doped with Ce3+, Nd3+, Ho3+, Er3+, and Tm3+ ions are obtained for the first time. Spectroscopic and laser characteristics of these crystals are discussed for Nd3+-and Era+-doped samples serving as representative examples. In particular, low-threshold stimulated emission was excited in 4F3/2?+4I11/2 channel of Nd3+ ions in the BaLu2F8. Room-temperature generation was obtained also at -1.317 µm wavelength for Nd3+ and at ~2.8 µm (several lines) for Era+ ions in this new laser crystalline host with a threshold of about 20 J.

Jan 1, 1997

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983

By Qingyun Huang, Junyi Xiang, Xuewei Lv, Chenguang Bai

The extraction of vanadium from mechanically activated converter slag was studied in dilute sulfuric acid solution. The effects of roasting and leaching parameters were investigated. The results show that Ca/V mole ratio, roasting temperature, leaching temperature, liquid-solid ratio, and particle size all have significant effects on vanadium leaching efficiency from calcification-roasted converter slag.

Mar 1, 2017

By Luiz A. Teixeira

A process is described whereby worn, deffective or crystallized photoconductive Se-As layers can be stripped off from aluminium photocopier drums, using hydrogen peroxide solutions in conditions such that the aluminium substrate is preserved from chemical attack. The process allows the stripped drum to be recoated with a new photoconductive layer, and to be put again in use.

Jan 1, 1990

By Cz. Mazanek

Specific biostimulating and anticancerous properties have been observed in peat, Ash Vacanta, and in an amorpous silica that is obtained as a by-product of alumina production from Turow clay in Poland. The anmphous silica was characterized and found to have a large specific surface area. This property may account for the beneficial characteristics of the material.

Jan 1, 1989

By Muammer Kaya

This paper reviews the existing and state of art knowledge for electronic waste (e-waste) recycling. Electrical/electronic equipments (EEEs) which are unwanted, broken or discarded by their original users are known as e-waste. The main purpose of this study is to provide a review of e-waste problem, give e-waste management strategies and introduce various physical e-waste recycling processes with special attention towards extraction of both metallic values and nonmetallic substances. The hazards arise from the presence of heavy metals (e.g. Hg, Cd, Pb etc.), brominated flame retardants (BFRs) and other potentially harmful substances in e-waste. Due to the presence of these substances, e-waste is generally considered as hazardous waste and may pose significant human and environmental health risks if improperly managed. This review paper describes the potential hazards and economic opportunities of e-waste. First of all, an overview of e-waste/printed circuit board (PCB) components and substances are given. Current status and future perspectives of e-waste and waste PCB recycling techniques are described. E-waste characterization, dismantling, liberation, classification and separation processes, are also covered. Manual selective dismantling after desoldering and metal-nonmetal liberation at −150 μm with two step crushing are seen to be the best techniques. After size reduction, mainly physical separation processes employing gravity, electrostatic, magnetic separators etc., which are commonly used in mineral processing, have been critically reviewed here for separation of metals and nonmetals. The recovery of pure metals from e-waste after physical separation can be performed by pyrometallurgical, hydrometallurgical or biohydro metallurgical routes, which are not covered here. Suitable PCB recycling flowsheets for industrial applications are also given. E-waste recycling will be a very important sector in the near future from economic and environmental perspectives for both developing and developed countries. Recycling technology aims to take today’s waste and turn it into conflict-free, sustainable polymetallic secondary resources (i.e. Urban Mining) for tomorrow. Recycling technology must ensure that e-waste is processed in an environmentally friendly manner, with high metal/nonmetal recovery efficiency a lowered carbon footprint. Taking into consideration our depleting natural resources, this Urban Mining approach offers quite a few benefits; it provides a substantial secondary resource, while also ensuring that the environment is kept free from harmful toxins in e-waste. This results in increased energy efficiency and lowers demand for mining of new raw materials.

Mar 1, 2017

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By Kimio Itagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte / FeOx SiO2, FeOx-SiO2-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523~1573K under controlled partial pressures of S2 and O2 at given PSO2 of 10.1, 50.7 and 101.3 kPa (0.1, 0.5 and 1 atm) and be observed dependency of distribution ratio on the matte grade, SO2 pressure and slag basicity were analyzed on the basis of thermodynamics,

Jan 1, 2003

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By M. J. Adam

The Bureau of Mines is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide phases by sulfidation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes research involving sulfidation partitioning of byproduct chalcopyrite concentrates from Missouri lead ore processing, and a Utah chalcopyrite concentrate from Cu ore processing. Small chalcopyrite samples were sulfidized with elemental S in glass capsules sealed after evacuating and backfilling with He, by heating for 1 to 24 h at specific temperatures in the range of 250? to 500? C, extending from below to above the boiling point of S (-4450 C).

Jan 1, 1987

By G. S. Gupta

To predict the iron oxide concentration a mass transfer model has been developed for an Induction Smelting Process (ISP) in which self-fluxed composite pellets (made of iron ore, brown coal and lime) are melted in a single phase induction furnace in conjunction with top blown oxygen. Transient mass balance equation with complex boundary conditions has been worked out by adopting a relatively new approach known as the cell model approach. These equations have been solved numerically using finite difference technique to obtain the iron oxide concentration profile in the ISP. Numerical and experimental results obtained for iron oxide concentration show a reasonable agreement with each other.

Jan 1, 1991

By Patrick R. Taylor

Thermal plasma technology has a wide range of applications in extractive and process metallurgy. Beneficiation of complex ores, oxide reduction, melting/remelting of refractory metals and scrap, and the recovery of precious metals from waste products are some examples of potential uses for plasma technology. The highly concentrated enthalpy provided by plasma torches is a cleaner energy source and may give higher processing rates per reactor volume than conventional technologies. Some of the other advantages may be: controlled furnace atmosphere, ability to treat fine feed materials and rapid quenching. A review of some of the uses for plasma processing in non-ferrous process and extractive metallurgy is presented.

Jan 1, 1993

By I. H. Gundiler

Sandia National Laboratories (SNL) is tasked to support The Department of Energy in the dismantlement and disposal of SNL designed weapon components. These components are sealed in a potting compound, and contain heavy metals, explosive, radioactive, and toxic materials. SNL developed a process to identify and remove the hazardous sub-components utilizing real-time radiography and abrasive water-jet cutting. The components were then crushed, granulated, screened, and separated into an aluminum and a precious-and-base-metals fraction using air-tables. Plastics were further cleaned for disposal as non-hazardous waste. New Mexico Bureau of Mines & Mineral Resources assisted SNL in investigation of size- reduction and separation technologies.

Jan 1, 1995

By Heikki K. Jalkanen

Thermodynamic properties of copper-iron mattes and slag-matte distribution of copper and some minor matte constituents (Ni, Co, Mo, As, Sb and Bi) are discussed on? the basis of equilibrium measurements: a change from. oxidic to sulfidic solubility as the predominant form of dissolution of copper takes place as matte grade decreases. Distribution coefficients of minor matte constituents are complex functions of sulfur and/or oxygen potentials?. The distribution behaviour of different? metals can be qualitatively derived from their affinities to copper and stabilities. of their sulfides and oxides. The equilibrium results are compared with commercially observed values. from Outokumpu.Oy flash smelting furnace.

Jan 1, 1983

By T. Shibasaki

Purification of copper electrolyte at Naoshima is carried out by two stage liberation to completely depress copper and impurity ions followed by concentration of the solution to produce crude nikel sulfate as by-product. A new nickel recovering process has been developed and pilot tested recently. It consists of the following process steps.; neutralization of spent electrolyte from liberation section to remove free acid and most part of remaining impurity ions, refining and nickel concentration by solvent extraction, and crystallization of pure nickel sulfate from concentrated strip solution. This paper describes the results of laboratory and pilot plant tests, then briefly discusses feasibility of the proposed process.

Jan 1, 1987

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

In this study, Raman spectroscopy was utilized to investigate the evolution of char structure in pulverized coal (PC) during microwave irradiation. The results indicated that though microwave treatment was carried out at low powers of 132W or 264W, significant variation in char structure was still observed. Char structure turned out to be more irregular firstly under microwave irradiation. However, char structure of superior regularity was obtained with the extension of irradiation time. It can be conclude that short time microwave treatment may facilitate the chemical activity of coal, while long time microwave irradiation on PC may deteriorate its combustion or pyrolysis property.

Jan 1, 2016