Search Documents

By Michael E. Stout

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993

By J. M. Boxall

The electrolytic zinc plant at the Bartlesville division of Z.C.A. originally used lead anodes containing only 0.25% silver because only H.G. zinc and alloy was to be produced. In 1984, a small addition of strontium carbonate was made to control the surf ace morphology of the cathodes which reduced short circuits and increased current efficiency. Later a drastic reduction in colloid addition further reduced short circuits. Increased strontium additions allowed the production of some S.H.G. zinc. Increasing the silver content of the anodes reduced the lead in cathodes only slightly. More important, the anode scale that was not removed during anode cleaning, entered the electrolyte and contaminated the cathodes with lead. A piping system has been installed to purge the contaminated electrolyte directly back to the leaching section. This has allowed the plant to produce S.H.G. zinc consistently.

Jan 1, 1990

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world's asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

By K. Ono

A new process for extraction of titanium metal from its oxide is demonstrated. In this process, row material to be reduced is titanium oxide synthesized from ilmenite. The reducing agent is the Ca+CaCI2 two-phase mixture. TItanium is elaborated in the medium consisted of liquid Ca, Caq and solid TI02 at the temperature range 1200 to l300K by means of mixing mechanically the ingredients in the reactor into a smooth paste. Fluidity of the feed which enables continuous scheme depends on the CaCl2 content. The oxygen level of the reduced titanium is the range 500 to 1000 mass ppm varying with the operational conditions. The Ca+CaCI2 reducing agent is taken out from the electrolysis of CaC12 at 11401(, and this CaCl2 is produced by aqueous chemistry conversion using Cl2 gas recycled from the electrolysis.

Jan 1, 2001

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Yutaka Saito

"Effect of moisture content must be fully understood for controlling the granule compaction of ceramics. It changes the mechanical behavior of spray-dried granules applied for compaction process, and governs the structure and properties of .ceramics. To understand the time-dependent change in processing, the kinetics was examined for change of moisture content for granules placed in a die and the pressed compacts also. The results were explained in terms of apparent moisture diffusion coefficients. They varied non-linearly with the PVA content in the granules. The results were explained through the non-uniform PVA distribution in the granules.IntroductionMoisture must be controlled in compaction process to produce the green compacts having uniform structure. It affects glass transition temperature of binder and thus the deformation behavior of powder granules under an applied stress. Several studies [1-7] have clarified the effect of moisture content on the compaction behavior of granules and the structure of resultant compacts for both die pressing and cold isostatic pressing (CIP) of pre-formed compacts. In these studies, the moisture contents in the system were equilibrated with the humidity in the atmosphere before compaction. In practice, however, the moisture content in the system may vary with time if the relative humidity of surrounding atmosphere is different from what the granules were equilibrated previously. This is very likely case in real production processes. However, the kinetics of moisture change in the granules as well as in the pre-formed powder compacts have not been well studied. For controlling the microstructure in a system, it is necessary to fully understand the kinetics of moisture change and its relevance to packing structure of powders."

Jan 1, 2000

By Grant E. Casley

Since 1970 Mount Isa fines Limited has made a significant increase in blister copper production from approximately 100,000 to 155,000 mt per annum and in fact 161,040 mt were produced in the calendar year 1974. Flowsheet developments including fluidised bed roasting and converter slag flotation are discussed, particularly their contributions to minimising major equipment changes in smelting and converting. The use of model- ling and simulation techniques for such an exercise is mentioned. The paper reports the alterations made to both equipment and operating techniques in the reverberatory furnace and converter sections to achieve the regular production of 250 mt of blister per converter day from a 41% Cu matte grade. The effects of flux composition on converting performance are highlighted. The air quality control programme is discussed in relation to its restriction of blister copper production.

Jan 1, 1976

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By John Dasher

One of our War Plants processed Bolivian concentrates as low as 17% Sn by the Arnhem process (pressure leach with HCL) and sent the waste acid down a ditch to Galveston Bay where the chlorides, mostly iron, hydrolyzed. Oyster men, and Texas, demandedimpoundment until a disposal process could be developed. A recycle process found by lab work was recommended, piloted and a plant built. This involved cementation of As Sb, Cu, Bi and Ag on light moving scrap iron and of Sn & Pb on Al turnings (then not recyclable), evaporation and crystallization of hydrous FeCl2, roasting crystals in a muffle furnace and absorbing HCI for reuse. The residue from leaching the low grade concentrates was floated to remove undissolved sulfides, classified and passed over sand and slimes tables to get a smeltable concentrate, a discardable sand tail and a slimes tail worth treating After desliming at 2 micro meters cassiterite, oxide flotation gave good, lab results; but commercial equipment wasn't adequate then. Chloride volatilization, with or without smelting gave high recoveries of Sn as SnCl2, whose marketing was questionable. I have heard this was finally fluxed and smelted.

Jan 1, 1992

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016

By Baojun Zhao, Zhixiang Cui, Zhi Wang

"Bottom blown oxygen copper smelting process has been developed in Dongying, China by Dongying Fangyuan Nonferrous Metals Co., Ltd. in commercial scale. This is the first modem copper smelting technology developed in China with the advantages of high oxygen enrichment, low temperature and autothermal operation. Production capacity of more than 100,000 tonnes per year of copper has been achieved through a single bottom blown oxygen furnace with instantaneous feed rates reaching up to 90 t/h. The main features of the bottom blowing smelting process are that high grade matte (up to 72 wt% Cu) can be produced at relatively low temperatures with 2-3 wt% Cu remaining in the smelting slag. Analyses of quenched smelting slag show that significant amount of magnetite crystals are present in the slags at operating temperature which indicates that the operating temperature was much lower than the liquidus temperature of the slag. After four years operation this new technology has shown great potential for expanding production capability and energy saving. Process development continues on the first commercial scale bottom blown furnace at Dongying Fangyuan Nonferrous Metals and a larger bottom blown smelting furnace is under construction.IntroductionFlash and bath smelting technologies are the major processes used in modem copper making industry [l]. Ausmelt/Isasmelt using top blown and Noranda/Teniente using side blown are typical and common bath smelting technologies. In 1980s-1990s Hunan Shuikoshan Mineral Bureau, jointly with China Nonferrous Engineering and Research Institute (now China Enfi Engineering Corp.), developed the concepts of the bottom blown oxygen processes for both lead and copper smelting [2]. After the pilot test on 3000 ton copper per year scale in 1991, it was not progressed to industrial scope."

Jan 1, 2013

By A. S. Block-Bolten

Two innovations in nickel-arsenic separation have been studied on a laboratory scale. The first requires only a nitric acid atmospheric leach without preliminary roasting and leads to favorable final conditions for precipitation of arsenic as highly stable FeAsO4, The second is an NaOH-H2O2 pressure leach which is an alternative to the known NaOH-O2 pressure leach. Either method offers the possibility of rapid and efficient separation of nickel from arsenic and is applicable, for example to the high grade niccolite deposits in the Great Slave Lake area of northern Canada.

Jan 1, 1982

By Xiaowen Liu

The DSC/TG, IR and XRD analysis were used to characterize the heating phase transformation of illite, which came from Ouhai deposit, China. It was discovered that the dehydration and de-hydroxylation of illite carried out stage by stage during heating. The adsorptive water and layer-inter water were dehydrated from room temperature to 500°C; and dehydroxylated in the range 500°C~800°C. In these stages of process, illite?s layer structure kept almost unchanged. After 800°Cillite began to change into disorder structure. At about 1100°C, the layer structure of illite had been destroyed, and amorphous SiO2 and mullite crystallite appeared. At about 1200°C the structure of illite completely destroyed and mullite crystal phase had become perfect..

Jan 1, 2006

By J. Pesl, U. Kemey, F. Sauert

"The CONTOP® smelting cyclone is a water-cooled, upright, high-intensity smelting reactor. The technology for the reactor was initially developed and brought into industrial-scale operation in the area of non-ferrous metallurgy. The two largest smelting cyclones were built with a capacity of 32 tons per hour of copper concentrate mix.The newest industrial CONTOP® plant treats up to five tons per hour of zinc-bearing residues including EAF dust. The highly concentrated zinc-lead oxide produced is sold to the zinc industry. The slag fulfills the leaching criteria and is used in waterway construction. The heat transferred to the cyclone cooling system and the off-gas boiler produces steam from which power is generated in a turbine.V AI has erected a new CONTOP® demonstration plant at MEFOS, Lulea, Sweden. A zinc volatilization rate of 90% was achieved during hot commissioning with Swedish EAF dust.Treatment costs in the range of 85 to 100 EUR per ton were estimated in a feasibility study on the treatment of 73,000 and 57 ,000 tons EAF dust for a group of steelmaking mills in Southern Europe."

Jan 1, 2000