Search Documents

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Susumu Okabe

Top blowing lances are employed by the Mitsubishi Continuous Copper Converter for the continuous supply Of reaction gases into moken bath. In order to minimize the refractory wear caused by the interaction between the furnace lining and the melt splash. optimum furnace design and blowing condition are? required. An empirical equation obtained by the physical model study enables the estimation of the splashing rate on a vel1ical plane at a certain distance from the lance.

Jan 1, 1996

By R. G. Reddy

Nickel solubilities in spent pickling solutions (i.e. HF-HNO3-H2O solutions ) were measured as a function of HF and HNO3 acid concentrations. The chemical analysis of the industrial pickling solutions and sludges were made. The stable phases observed in the sludges are FeF3?3H2O, and ( FeCr ) F3?3H2O. Pure Ni, and stainless steel type 316 were used in this study. The results showed that the solubility of Ni increased with increase in concentrations of HF in pickling solution at a fixed concentration of HNO3: An excellent agreement between the experimental solubility data and the theoretical data was obtained. X-ray diffraction analysis showed that the solid solubility product formed is mainly NiF2?4H2O compound.

Jan 1, 1992

By Mikko Loponen

Outotec has developed an operator training simulator (OTS) platformsuitable for various hydrometallurgical processes. The complete solution is run in the cloud, where virtual client instances can be managed on-demand. The aim is to build a generalizable model that produces coherent results even when operating outside of ideal parameters, allowing the operator to train in unsteady state conditions such as start-up and shutdown. Complex software products are commonly associated with significant development time and cost. Utilizing modular software architecture, only the control system and processmodel are tailored for theOTS,whereas modules such as user administration and cloud-based client machine spawning can be imported, shortening development time. A generic acidic pressure oxidation process (POX) operator training simulation consisting of feed preparation, autoclave, dual-stage flash evaporation and off-gas scrubbing is described. Process is simulated using Outotec HSC Sim 9 process simulator and controlled by Siemens Simatic PCS7 control system.

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By R. G. Reddy

Viscosities of alkaline metal oxide-silicate melts were estimated using our previously developed mathematical model. The structural based model considers depolymerization effects and related breakdown of the silicate network structure, on the addition of metal oxides to the melt. The developed expression: n =4.9x10 9 NO 0 T ½ exp(E/RT) poise was used to calculate the viscosities of various binary silicate systems such as, CaO-SiO,, MgO-SiO, and MnO-SiO,, as a function of temperature and composition. Excellent agreement was obtained between the calculated and experimentally determined viscosities.

Jan 1, 1991

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By I. A. Ibrahim, A. K. Ismail, A. A. I. Afifi

"Synthetic rutile for paints industry is conventionally produced by a combined smelting and leaching process. Smelting process is an energy intensive step and represents economic burden in view of the increasing energy costs. Egyptian ilmenite ore containing 40% TiO2 and 38% total Fe was thus directly leached with sulphuric acid to produce eventually synthetic rutile. The process-involves digestion of the ore with sulphuric acid whereby both TiO2 and Fe are dissolved. The solution was then treated with iron powder to convert Fe3+ to Fe2+ to avoid co-precipitation of iron during the hydrolysis step. After solid/liquid separation and clarification, Fe was crystallized as ferrous sulphate hydrate by chilling. The titanium pregnant liquor was concentrated by evaporation and then hydrolyzed to precipitate hydrated titanium dioxide which was then calcined to produce synthetic rutile containing 98.6 TiO2 and 0.58% Fe2O 3. The optimum conditions of all the processing stages were determined.IntroductionSynthetic rutile for paints, welding rods and other industries could be produced from ilmenite ore by sulfuric acid leaching process. This process is a batch process and nearly 80% of all TiO2 produced in the world is made by this process [1]. Figure l shows simple block flowsheet of the process. The process involves the following stages.Digestion: In this stage, ilmenite ore is treated with concentrated sulfuric acid where both iron and titanium are converted to their respective sulfates according to the following equations:"

Jan 1, 2000

By J. Rajek

The novel multi-component, multi-particle, multi-phase precipitation model developed recently is used to predict the precipitation kinetics in complex 9-12% Cr steels investigated within the European COST 522 project. These steels are used for tubes, pipes, casings and rotors in USC (ultra super critical) steam power plants for the 21st century. In the computer simulations, the evolution of the precipitate microstructure is monitored over the entire production heat treatment starting with the casting process, including austenizing, several annealing treatments and in-service conditions. The main interest lies on the concurrent growth and coarsening interaction of different types of precipitates. Keywords: Precipitation kinetics, heat treatment, power plant steels, simulation

Jan 1, 2003

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By Billy W. Osborne

The use or primary dross as a source for aluminum ion in the manufacture of aluminum sulfate offers opportunities for an inexpensive raw material. The aluminum sulfate industry in the US is a mature market with numerous small plants operating close to major users. The majority of manufacturers use either bauxite or aluminum oxide trihydrate as a source for the alum¬inum ion.. However, using process technology developed and patented by IWC, the oxides are removed from primary dross for use in manufacturing aluminum sulfate prior to metal recovery. This process offers the benefit of reducing costs for metal recovery. This paper discusses some of the methodology used in this process.

Jan 1, 1995

By Liangju He, Peixuan Ouyang, Peijie Li

Single-pulse laser ablation of aluminum and titanium alloys under glass confinement is investigated. Processing parameters such as laser intensity and gap width between targets and glass are varied. Surface morphologies and crater profiles of the alloys after laser ablation are studied by SEM and white-light interferometric microscope, respectively. The effects of gap width and laser intensity on surface morphologies and crater profiles of targets are systematically analyzed. In addition, the generation of porous surface structures in Ti target is regarded as the result of phase explosion in the molten surface layer of targets and the thermodynamic condition in our experiment for phase explosion is evaluated.

Jan 1, 2016

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Jorge D. Vier, Raúl B. Rebak, Alicia E. Ares, Natalia S. Zadorozne

Recent worldwide demand has driven nickel and molybdenum prices to record high values. Alloys containing significant amounts of nickel and molybde- num, such as the austenitic and duplex grades, have experienced significant price increases and some spot shortages have resulted in some regions. With low or no nickel content and reasonable molybdenum content, super-ferritic stainless steels are now proving to be the most cost effective corrosion resistant materials. The electrochemical behavior APMT® (Fe–21Cr–5Al–3Mo–0.04C) and 4C54® (Fe–26.5Cr–0.8Mn–0.5Si) super-ferritic stainless steel in NaCl solutions has been studied using open circuit potential measurements, potentiodynamic polarization curves, and electrochemical impedance spectroscopy. The aim is to compare the behavior of these materials with austenitic stainless steel alloy 316 (Fe–18Cr–10Ni– 2.5Mo). The results indicate that the APMT alloy presents a better performance than the AISI 316 stainless steel, while 4C54® does not, especially at anodic potentials. The good behavior of APMT® may be attributed to Al and Mo content in its composition.

Mar 1, 2017

By M. J. Adam

The U.S. Bureau of Mines is investigating the partitioning of selected complex minerals into simple phases using sulfidation reactions. Successful partitioning of complex mineralogy to simple phases may afford an opportunity to improve selective extraction of mineral constituents of economic value. The research has shown that complex minerals, such as chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9Se]' may be partitioned to the simpler phases covellite (CuS) plus pyrite (FeS2) and vaesite (NiS2) plus pyrite (FeS2), respectively. Demonstrations of these reactions were verified through long-react ion-time (24 h or more) experiments, but basic rate investigations and modeling were not included in the previous research. This report describes research aimed at determining the rate at which the complex mineral CuFeS2 converts to the simple sulfides CuS plus FeS2. Small samples of CuFeS2 were blended with elemental S prior to thermal treating under an He atmosphere for time periods up to 4 h. Products from each treatment period were characterized using metallography, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of the investigation revealed a rapid conversion of CuFeS2 to CuS plus FeS2 early in thermal treatment periods. As the reaction occurred, a CuS rimming of particles was observed which separated the reacting species (CuFeS2 and S) and caused a considerable decrease in transformation rate.

Jan 1, 1991

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991