Search Documents

By Jean Goldschmidt

Recycling of fine oxidized particles of non-ferrous metals usually cannot be carried out by pyrometallurgical methods. 'Hydrometallurgy provides an alternative technology to reintroduce? the resulting products as secondary raw materials into the industrial cycle, thereby saving resources and energy while keeping the environment a little cleaner. The paper summarizes the methods employed by Hydrometal to achieve these objectives and? stigmatizes the latest counterproductive international regulations which create ever more obstacles to environmentally sound recycling.

Jan 1, 1995

By Heimo Thalhammer

During the refining of lead, copper or other metals the furnaces used in the process · often produce waste gases. This paper illustrates how these waste gases can be successfully treated and destroyed by CTP 2-bed or multi-bed compact systems, modified for the additional reduction of dioxins and furans. The CTP regenerative thermal oxidizer also destroys voes (organic compounds and odours) using ceramic blocks as a heat exchanging media. The raw gas is forced through the ceramic beds where it is heated up to the oxidation temperature level. The voes, dioxins and furans are destroyed in the combustion chamber, subsequently generating water, eo2 and heat. The hot purified gas heats up a second ceramic bed, which is used to preheat the raw gas after the valves have been switched. This process does not produce any secondary waste such as contaminated water, polluted air or any other products that have to be disposed of.

Jan 1, 2000

By Muhammad A. Imam, Ramana G. Reddy

This study provides a reasonable evaluation of the Mg-B binary system. Magnesium and Boron (Mg-B) alloys were investigated to determine their thermodynamic properties employing solid state electrochemical cells based on CaF2 electrolyte represented as –Pt; Ar= MgþCaMgF4 f gCaF2 k kf½Mg B alloy þ CaMgF4 g=Ar; Pt+ Investigations were performed over the temperature range of 773–873 K to measure the electromotive force (EMF), which was used to derive the partial Gibbs Free energies of the alloys in the composition range of XB = 0.07 to 0.95. The activities of Mg were also calculated from partial Gibbs Free energies. The activities of Mg in MgB2, MgB4, and MgB7 were expressed as a function of temperature respectively, ln aMg = 4.27–9.32 × 103/T, ln aMg = −7.54 + 6.67×103/T, and ln aMg = 4.93–19.57 × 103/T, where T is the temperature in K. From this expression, the activity of Mg for these intermediate phases can be extrapolated at a higher temperature to get the accurate phase boundaries for the Mg-B system.

Mar 1, 2017

By Markus A. Reuter

In this paper various hybrid modelling architectures are proposed for the modelling and metallurgical control of pyrometallurgical reactors. Discussed are architectures in which data reconciliation is combined by thermochemical, neural net and dynamic modelling to improve the models. At the same time the data reconciliation models can act as soft-sensors for estimating unmeasurable data. Cases that are discussed are (i) the modelling of a submerged arc furnace for the production of thermal phosphorous, (ii) the processing of Sn-Pb-Zn flue dust (originating from secondary copper) in a hearth furnace, (iii) modelling of a steel converter, and (iv) dynamic modelling of a flash smelter.

Jan 1, 2001

Rapidly solidified TiAl-Cr-xNb-Y(x=2,4,6, at.%) alloys have been produced using a single roller melt spinning method. The microstructure of alloy ribbon was refined and component became more homogeneously by rapid solidification technology. There were two phases in alloy ribbons, including -TiAl and 2-Ti3Al phases, yet the amount of 2-Ti3Al phase in matrix obviously increased by rapid solidification than cast alloys. The micro-hardness testing also carried out. Compared to the cast alloys, the alloy ribbons have much higher hardness.

Jan 1, 2009

By Ping Long, Bin Yang, Jian Wu, Xiumin Chen, Wenli Zhang

In this study, the analysis method of trace element in pure indium using glow discharge mass spectrometry (GD-MS) has been established by correcting the analysis result, which was obtained from non-standard quantitative method of GD-MS. The effect of instrument operating parameters, the resolution and isotopes and the pre-sputtering time on the determination results were investigated respectively. The optimized operating parameters of the instrument were obtained as follows: the discharge current was 37.5mA and discharge airflow was 475ml/min. Mass spectral interferences have been eliminated using selected resolution and isotope. The pre-sputtering time was 30 min. 4 trace elements in two pure samples were determined for 6 times. The RSD were less than 20%. The content of trace elements in indium samples was determined by GD-MS and Chemical Analysis Method of Indium which is tested by inductively coupled plasma atomic emission spectrometry, respectively. The results were consistent with each other.

Jan 1, 2016

By Manis Kumar Jha, D. D. Pathak, Archana Kumari

Treatment of secondary/waste to recover rare earth metals (REMs) is gaining importance due to its increasing global demand, lack of availability of high grade natural resources and huge generation of secondaries. Present paper reports the critical review on available processes for recovery of REMs from secondaries viz. manufacturing scraps, e-waste, industrial residues such as red mud, fly ash, waste water, etc. Hydrometallurgical processes with combination of Beneficiation/ Pyro-/Electro techniques are discussed to recover REMs effectively. The recommended processes require less energy to deliver high purity yield which is one step towards green environment. Salient findings on various methods are reported with recommendations which will be helpful to researchers working in the area of REMs extraction.

Mar 1, 2018

By R. M. Moon

Neutron scattering has played a crucial role in advancing our understanding of rare-earth materials. It has provided a detailed description of the rich array of exotic magnetic structures; it has confirmed the accuracy of theoretical wave functions for the 4f electrons; and it has provided fundamental data on the collective magnetic excitations in these materials. The fundamental property of the neutron which has been exploited in this work is the magnetic interaction which exists between the magnetic moment of the neutron and atomic magnetic moments on individual rare-earth atoms. This interaction produces scattering of neutrons in a manner closely analogous to the scattering of X rays by atomic charge distributions. In a material exhibiting long-range magnetic order, Bragg diffraction peaks will appear at scattering angles determined by the periodicity of the magnetic structure. The Bragg intensities are determined by the magnitude and relative directions of the atomic moments. The rare-earth metals and alloys are characterized by sinusoidal modulation of magnetic moment components which can be combined in various ways to produce a variety of magnetic structures. The periodicity of these modulations is frequently not related simply to the underlying periodicity of the chemical structure. The major features of these structures are explained by the combined, and sometimes competing, exchange and crystal-field interactions. At a more fundamental level, neutron diffraction also gives information on the spatial distribution of a magnetic moment in a rare-earth atom. This moment comes from the 4f electron shell, and accurate measurements of the neutron scattering amplitudes have been used to check the accuracy of atomic wave function calculations for the 4f electrons. It was found that relativistic Dirac-Fock calculations are in excellent agreement with the experimental results. Collective excitations of ordered magnetic systems are described in terms of spin waves, which are sinusoidal modulations in space and time of the direction of the ordered moments. Inelastic neutron scattering is used to measure the energy and wave length of these collective excitations. Analysis of these data gives direct information on the interatomic interactions responsible for the magnetib properties of these materials.

Jan 1, 1992

By He De-wen

The influence of wastewater containing benzene from chemical industry by technology combined blow-off with Fenton reagent oxidation was experimentally studied. The present results suggest that the technology combined blow-off with Fenton reagent oxidation can effectively remove benzene pollutant in wastewater. The main factors that influence the removal benzene such as temperature and blowing time and volume, pH and reagent dosage of H2O2 and Fe2+ are studied and the optimal experimental conditions are as follows: time 20min, temperature 40i, air-blowing volume 0.4L/min, pH value 5, and H2O2 and Fe2+ dosage 2mL/L and 200mg/L respectively. Under the above conditions, benzene pollutant can be removed up to 97%. Compared to other removal ways of wastewater containing benzene, the technology combined blow-off with Fenton reagent oxidation is more effective and has the advantage of high speed.

Jan 1, 2009

By Yuanbo Zhang, Guihong Han, Guanghui Li, Tao Jiang, Zengqing Sun, Yanfang Huang

"Because of small specific surface area and poor ballability, vanadium/titanium-bearing magnetite is difficult for production of oxidized pellet. A novel organic copolymer binder, modified humic acid (MHA), has been authorized recently in China. Effects of the novel MHA binder on the quality of V/Ti-bearing magnetite pellets are studied in this paper. Experimental results show the MHA binder can obviously improve the strength of green pellet. Because of better heat endurance, the MHA binder pellet has a higher strength than Peridur pellet under the same preheating conditions. Moreover, TFe grade of pellet with the MHA binder is much higher than that of the bentonite pellet. The strength of preheated pellet containing MHA binder of 0.25%~1.0% meets the requirements of oxidized pellet production by grate-kiln process. Comparatively, MHA is a promising orgainc binder for iron ore pellets. Its price is only one tenth of Peridur price and about 3 times of bentonite price.IntroductionThe iron-making practices show that the use of pellet is beneficial to blast furnace life, productivity and fuel savings. Therefore, many iron-making plants have expanded the production of oxidized pellets in order to meet the needs of modern large-scale blast furnaces [1]. Presently, bentonite is widely used to improve the quality of iron ore pellets. The negative effects of using bentonite include decreasing total iron (TFe) grade and degrading the metallurgical properties of the final products [2, 3]. Many studies, therefore, have been conducted on the application of organic binders to overcome the weakness of the inorganic bentonite. In comparison with inorganic binders, one of the biggest strengths of organic binders is low residual silica content [4]. However, those studies showed that the economics of foreign organic binder addition into pellets was not attractive. For example, the compression strength of preheated pellets and roasted pellets are both too low, resulting in powder generation and ring formation in the industrial rotary kiln [3, 4]."

Jan 1, 2011

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Melvin H. Miles

"Considerable research has been conducted on the anodic oxidation of methanol in fuel cells. The electrochemical reduction of carbon dioxide in aqueous solutions to form methanol is the same reaction in reverse, i.e. CO2 + 6 H+ + 6 e- ? CH3OH + H2O. The same catalysts and conditions may operate for both reaction directions. This carbon dioxide reduction reaction, however, must be able to compete with the electrochemical reduction of water to form hydrogen gas. Thermodynamically, the reduction of CO2 to form CH3OH is slightly more favorable than the reduction of water. The use of nearly neutral electrolytes rather than acidic electrolytes makes the reduction of CO2 kinetically more favorable. The thermodynamics of various reaction steps are presented. Similarities exist with the electrochemical reduction of CO2 and the green-plant photosynthesis process that converts CO2 to carbohydrates.IntroductionVirtually all of the oxygen in the earth’s atmosphere is of biological origin having been generated by green-plant photosynthesis from water and carbon dioxide [1]. The net reaction can be represented byCO2 + H2O ? O2 + [CH2O] (carbohydrates, etc.) (1)Chlorophyll and enzymes promote this reaction, and the energy required comes from sunlight. The actual photosynthesis process is a complex multistage reaction and requires 469 kJ mol-1 of energy supplied by the sun. Isotope tracer experiments using 18O have shown that both the oxygen atoms in the O2 molecule originate from H2O, whereas oxygen atoms in the carbohydrates come from CO2 [1]. The total amount of water on the earth is split by photosynthesis and reconstituted by respiration and combustion once every 2 million years or so. The photosynthetically generated oxygen gas temporarily enters the atmosphere and is recycled about once every 2000 years [1]. The carbon dioxide is partly recycled in the atmosphere and oceans after an average residence time of 300 years and is partly fixed by precipitation of CaCO3 and other carbonate minerals [1]."

Jan 1, 2008

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By Onuralp Yucel, Ahmet Turan, Murat Alkan, Hasan Ozer

SHS (Self-propagating High-temperature Synthesis) is one of the important methods to synthesize B4C powders. The process contains the reaction of boron oxide powders (B2O3) with magnesium reducing agent and carbon black carburizer. SHS products are leached in HCl media to purify synthesized B4C powders in the following step. In the present study, effects of various functional additives (KClO3, KHSO4, MgSO4.7H2O, NaCl, MgO and Na2SO4) in the SHS stage were carried out. Various proportions of the additives were mixed with the initial SHS charge mixtures. Two different molar ratios were employed in the initial SHS mixtures as 1:3:0.8 B2O3:Mg:C and 1:2.5:0.8 B2O3:Mg:C. After the SHS step, HCl leaching process was applied to the SHS products. Filter cakes were dried and characterized by using X-Ray Diffraction Spectroscopy, BET and chemical analysis techniques.

Jan 1, 2015

By Jianhang Hu, Li Yang, Yonggang Wei, Kongzhai Li

"In this paper, the pyrolysis of biomasses including bamboo, sawdust and walnut shell were performed in a tube furnace under temperatures between 400? and 600? to obtain biomass carbon, gas, and tar. Textural parameters analysis revealed the caloric value of biomass carbons between 32 MJ/kg and 34 MJ/kg. It also indicated that the surface of biomass carbon consists of mesopore and macropore structures. By using GC analysis, it was determined the main ingredients of pyrolysis gas are CO, H2, CO2, CH4, C2H4 and C2H6. Calculation states that the density of pyrolysis gas is roughly between 1.0 kg/m3 and 1.7 kg/m3, while the calorific value of pyrolysis gas is between 12000 kJ/m3 and 16500 kJ/m3, illustrating that pyrolysis gas is a median gas. The calorific value of biomass tar was found to be between 32 MJ/kg and 34 MJ/kg, with more than 80 compounds in the biomass tar identified by GC-MS method.IntroductionBiomass as a renewable source is the world's largest and most sustainable energy resource [1].The conversion of biomass has the potential to be a renewable and carbon neutral method of producing fuels and chemicals [2-4]. Pyrolysis is a thermo-chemical process defined as applying heat to degrade biomass in an inert atmosphere. It transforms unstable biomass and other organic materials into biomass carbon, gas, and tar [5]. Biomass carbon can be stored or transported much easier as compared to parent biomass or be converted to value added products such as activated carbons[6]; gas is a relatively low-energy-density fuel; tar can be considered as a source of useful chemicals[7].The characterization of biomass pyrolysis will lead to its increased understanding and utilization as a source of solid, liquid and gaseous products which can be used as fuels and petrochemical feedstock[8,9].In recent years, many researchers studied the effect of temperature on biomass pyrolysis product distribution characteristics in a variety of pyrolysis reactor[10]. Ramin Azargohar's paper [11] presents the results of characterization for biomass and investigates the effects of pyrolysis temperature on the pyrolysis products obtained by fast pyrolysis of four different types of biomass."

Jan 1, 2014

By Z. Jing, C. Jun

High-purity Bi2O3 was prepared via extraction-preparation stripping method use BiCl3 leaching solution. Parameters such as oxalic acid concentration, phase ration, aging duration, feeding duration, were examined for their effect on the size and morphology of precipitate. The precipitate was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), particle size analysis, differential scanning calorimetry and thermal gravity analysis (DSC-TGA) and infrared spectroscopy analysis (FT-IR). Bi2O3 was characterized by elements analysis, particle size analysis and scanning electron microscopy (SEM). Bi2O3 product of 680 nm was obtained using 15 g/L oxalic acid, 1/1 phase ration, 0 min aging duration, 0 min feeding duration and calcinating at 500 °C for 2 h.

Mar 1, 2018

By T. J. White

Xtaltite is the trade name for a generic technology which exploits the well known insolubility of some minerals, which naturally incorporate toxic waste elements, to consolidate and immobilise a range of inorganic waste products. It is a specific case of synthetic mineral immobilisation technology (SMITE) which is already used to immobilise high level nuclear wastes (HLW. Although HLW is highly toxic, it exists in relatively small volumes, occurs in central facilities and may be stabilised at low waste loading (< 10 wt%). In contrast, heavy metal wastes are of considerable volume, therefore Xtalitite waste forms must routinely accommodate high waste loadings (usually in excess of 30 wt% for a particular toxic oxide or combination of oxides) and be suitable for fabrication in remote locations using relatively simple technology. This paper details the methodology underlying Xtaltite, with particular emphasis given to the interplay between solid state chemistry, durability and economic considerations. Specific reference is made to the treatment of arsenious and mercurial wastes.

Jan 1, 1994

By Robert De Saro, Willis Bateman, Ramesh Jain

A Vertical Floatation Melter (VFM) has been developed (sponsored by DOE) which simultaneously decoats and melts organic laden scrap in a single unit. Scrap aluminum is fed into the top of the VFM where it falls through a cone. Hot gases flow upwards through the cone, imposing a variable drag force on the scrap. Equilibrium is reached in which the scrap weight equals the drag force and the scrap becomes suspended. The gases strip off and vaporize the organics. Next, the scrap reaches a liquid state, taking on a more aerodynamic teardrop shape, allowing it to fall into a holding furnace. Heat transfer coefficients are 10 times higher than that of a conventional furnace, allowing rapid melting at a low gas temperature. Typical energy use is well under 2,324 joules/g (1,000 Btu/lbm) with a metal yield from 92 to 98%. This paper reports on the operation and data of a 453 kg/hr (1,000 pph) pilot-scale VFM.

Jan 1, 2000

By R. Parada

In January 1995, Disputada Mining Company Ltd. (Compañia Minera Disputada de Las Condes) started up the Expansion Project for the Chagres Smelter, following an investment of US$M 2 15. The new smelter replaced the 44,000 tomes per year revervatory furnace with an Outokumpu Flash Smelting Furnace (FSF) designed to produce 118,000 tonnes per year of copper. Nowadays, this smelting unit has achieved a 40% over design performance. The landmarks of this modernization project are described. The start up period in 1995-1996 was characterized by the impacts of several restrictions that prevented the smelter from reach design production. The design performance was reached in 1997-1998 through the implementation of solutions designed to eliminate, or at least mitigate, the restrictions found early on. The smelter has been further optimized in the 1999-2000 period, leading to a new record anode copper production rate of 148,000 tonnes in 2000 while obtaining 98% approval for our different anode shapes. The objective of this paper is to discuss the consecutive processes of start-up, achievement of design capacity, and operational improvements to go well beyond the design capacity. These processes took place between early 1995 and late 2000, under the principles of Continuous Improvement that promotes the effective participation of the workers in the technology innovation and Enterprise Management.

Jan 1, 2002

By I. A. H. Schneiderl

Eichhornia crassipes approaches being a scourge in many parts of the world, .choking waterways and hindering transport upon them. At the same time it is known to readily abstract heavy metal ions from water and, thus, aids in the removal of heavy metals found in such waters. This paper considers the possibility of using specific parts of the plant as an inexpensive adsorbent for the removal of heavy metals from contaminated chemical and mining industry waste waters. In particular the root of the plant was found to be an excellent accumulator of &apos;heavy metal ions including uranium from solution. It is. also suggested that dried roots of the plant ?might be placed in simple bags and used in a very low cost metal ion removal system.

Jan 1, 1995