Search Documents

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander model for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2, MgO-SiO2, FeO-CaO-SiO2, FeO-FeO1.5-CuOo.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-MgO and FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte (L s/m as), and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5-CaO-MgO slag and liquid copper (L s/Cu as) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte-metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for prediction in multi-component slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes.

Jan 1, 2003

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By Janene Barter

Telfer Gold Mine treats both gold/copper oxide and sulfide ores in a remote location in the Great Sandy Desert, Western Australia. Currently, the oxide gold ore is treated in a conventional CIL circuit by blending the low and high grade copper ores to minimise cyanide consumption and allow smooth operation. The sulfide ore is treated through a flotation circuit to produce pyrite and copper concentrates. The pyrite concentrate is treated in the CIL. Copper concentrate is stockpiled and sold to a smelter for further processing. In recent times, as the depth of the pit has increased the copper head grade has also increased, to the point where the ore was becoming uneconomical to treat. In addition, it was desirable to reduce the amount of cyanide reporting to the tails dam both from an environmental and economical viewpoint. Newcrest Mining Limited engaged GRD Minproc Limited to evaluated a process to reduce the amount of cyanide entering the tail dam with consideration given to copper recovery. From this investigation, the Sulfidisation, Acidification, Recycle and Thickening (SART) process was selected. A detailed testwork program for SART was undertaken with the objective to design and construct a SART plant at Telfer. This paper outlines how the SART process was chosen and summarises the testwork that led to the design of the SART plant. It also touches on some of the important issues for designing this type of process.

Jan 1, 1998

By K. J. Cathro

A hydrometallurgical process is described for the recovery of copper from chalcopyrite concentrates. The process is based on a cupric chloride leach, the concentrate having first been "activated" by heating it with sulphur at a temperature near 400°C. This activation process converts most of the iron of the chalcopyrite to pyrite, which is insoluble in the cupric chloride leachant. The copper is converted to the mineral idaite, which dissolves readily in hot cupric chloride: at 106°C, 98% of the copper is extracted in a three-stage countercurrent leach, the leaching tirqe being 1 hour per stage. The sulphur of the chalcopyrite appears as elemental sulphur, which is recycled for the activation of further concentrate, the final leach residue consisting of pyrite, plus the gangue present in the original concentrate. The copper extracted can be recovered by electrowinning, using a diaphragm cell. Current efficiency (one-electron basis) is about 70% but the cell voltage is only about 1 V, so that power consumption is three times lower than for the conventional sulphate electrowinning process. The leachant is simultaneously regenerated in the anode compartment. The behaviour of minor elements in the concentrate has also been studied.

Jan 1, 1976

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander moderl for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2,MgO-SiO2, FeO-CaO-SiO2, FeO1.5-CuO0.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-Mgo and FeO-FeO1.5-CuO0.5-CaO-Mgo-SiO2, slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte mn (Lx, )' and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5*-CaO-Mgo slag and liquid copper (Ls/cua) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte- metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for predication in multi-componet slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes,

Jan 1, 2003

By Li Chen

A new process, i.e. Ball milling--Neural leaching--Oxidation calcinations--Chloridizing distillation--Hydrolysis, was designed to recover germanium from the vacuum furnace slag produced in Shaoguan smelter. The suitable process and operational parameters were determined for the practical production.

Jan 1, 2005

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By Weng Fu

In this study, Resin-in-Pulp (RIP) technology is used to separate Pb from a chalcopyrite slurry. Solvent-impregnated resin, Lewatit® VP OC 1026, which contains di(2-ethylhexyl) phosphoric acid (D2EHPA) in a macroporous polystyrene matrix was used, as the functional group exhibits selectivity for Pb over Cu. Adsorption pH, kinetics, as well as resin and CuSO4 concentrations were investigated. The results show that the kinetics of Pb and Cu loading are fast, reaching the adsorption equilibrium within 30 min. The equilibrium pH of 2 was chosen as optimum for operation in order to achieve a high Pb extraction rate and extent as well as selectivity for Pb over Cu. High Cu(II) concentration in solution results in Pb(II) requiring a larger amount of resin for the same degree of extraction. Regeneration and reuse tests show that the loss of adsorption capacity happens in the 1st and 2nd cycles and then the adsorption capacity stabilises for the 3rd cycle.

By H. K. Lin

Thermodynamics of Cu-C1-H2O system and the kinetics of copper dissolution in cupric chloride solution were studied with emphasis on possible difficulties which may occur during copper electrowinning. E,-pC1 diagram of this system wasestablished. Equilibriumdistributionof various copper chloride complexes of different valent states at the presence of metallic copper was computed through the relations of the simultaneous equilibria. The mechanism-of copper dissolution in the cupric chloride solutions was proposed and the mechanism of copper electroposition was discussed. The researched results were used for guiding the investigation of copper electrowinning from cupric chloride solution.

Jan 1, 1991

By Chris T. Vild

"ABSTRACT NOT AVAILABLEPRESENTATION SUMMARYIntroductionToday, light gauge aluminum scrap is melted in sidewell furnaces using natural gas reverberatory burners. The scrap is introduced into the sidewell adjacent to the combustion chamber through a submerged archway. Super-heated metal is then pumped into the sidewell where it aids in melting the scrap. From the sidewell, the flow is returned to the combustion chamber through a second submerged archway at some lower temperature. Normally, the burners are set at a designed high fire level and the scrap is introduced at a rate to attempt to mat.ch the burner input. A thermocouple in the bath is programmed to throttle back the burners to low fire if a high temperature limit is exceeded.Jn many cases the thermal efficiencies of these furnaces can be very low. With inadequate circulation, air and natural gas furnaces run at a dismal 18% thermal efficiency. If a circulation system· is added, the efficiency can jump to 28%. For a $100 million lb/yr recycling facility, and natural gas prices reaching $4.50 per million Btu, fuel cost at 18% efficiency can reach $1 million per year. A 10% increase in thermal efficiency saves $350,000 a year in fuel costs.With an increase in thermal efficiency, furnace utilization also increases. A 10% increase in thermal efficiency would result in a 20 million Btu furnace producing 12,000 lb/hr up from 8,000 lb/hr or 35 million lb more produced per year. This is a 33% increase in output.Most current furnace development has focused on burner technology using oxy-fuel, regenerative burners, etc. However, thermal efficiency is also largely effected by the molten metal circulation rate and how well the scrap is mixed into the superheated metal. Therefore, the flow dynamics should be optimized first, before installing of more thermal power.Jn an effort to understand the effect of these variables, a series of computer models were made and the critical factors studied with the goal of demonstrating an increase in thermal efficiency and production. Large-scale graphical representations of these models will be presented."

Jan 1, 2000

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By Björn Hinzel, Joachim Rösler

"The most important characteristic of open-pored metals is porosity, since it enables all of their functional applications as filters or sound absorbers. Due to the notch effect of the pores, mechanical properties of porous metals are better than the ones of comparable structures made of polymers or ceramics. Consequently, only open-pored metals can be used in aircrafts to reduce flow noise or noise resulting from the core engine by acoustic absorption. Absorption properties depend highly on pore size and porosity of the material, which must be characterized as precisely as possible in order to analyze the correlation between morphology and noise reduction performance. Here, a line segmenting method is explained in order to characterize pore size and porosity of absorber materials using image processing based on two dimensional microscopy images, including sample preparation and specification of the set-up. Then, the influence of the pore structure on the measured absorption behavior is discussed. Finally, the correlation of acoustic behavior, pore morphology, and porosity is outlined.IntroductionSignificant noise loads affect everyone causing anxiety, depression, insomnia and other effects which impair health and productivity [1],[2]. Due to the rising number of flights and aircrafts, air traffic noise increases dramatically. To counter this development, various approaches have been developed to reduce the different noise sources resulting from airframe, jet or engine [3],[4],[5],[6]. One approach to reduce this noise is the application of noise reducing liners in the hot gas path [7]. This is especially important, since the engine is becoming the dominant noise source of modern airplanes during take-off [8]. Due to the elevated temperatures and high fatigue loading in this part of the aero-engine, conventional passive absorber materials cannot be used. Polymers would not be able to bear the heat and ceramic fibers would crack under the mechanical loading due to the notch effect. Consequently, this study focuses on metals with open pores, which can resist elevated temperatures and fatigue loading and additionally resemble geometrically conventional passive absorbers. Based on the production processes, e.g. sintering of metal fibers [7], powder processing using a foaming agent [9], coating of polymer foams [10], or using melt infiltration techniques [11], the characteristic dimension of the porosity is usually in the range of 0.01-10mm. In this work, sintered metals and metal sponges are analyzed after the theory of sound absorption is briefly outlined. Then, measurements of the acoustic absorption of metal sponges and sintered metals in an impedance tube are performed. To understand and predict the acoustic properties of metals with open porosity, it is necessary to characterize the materials as precisely as possible. This is explained in detail using a line segmenting technique, followed by a discussion of the connection of pore characteristics and acoustic absorption. Finally, a conclusion is given."

Jan 1, 2012

By Tiruttani Munikamal, Suresh Sundarraj

"A numerical model of the induction hardening process of steel cranks has been developed and the predicted results of temperature and phase distribution during this solid state phase transformation process are verified with experimental data from the literature. This heat treatment process involves heating the crank to the austenitic temperature range followed by rapid quenching in water to harden the surface of the crank. The model has been developed using ABAQUS, commercial FEA software. The formation of martensite, pearlite, and retained austenite phases are modeled and implemented through a user defined function in ABAQUS. A sensitivity study on the various process parameters affecting the amount of phase distribution has been carried out.IntroductionThe type of surface and sub-surface microstructure as well as the residual stresses that are present in a component after manufacturing, significantly affects it fatigue performance. The wear resistance of the automotive components such as crankshaft, gears, camshaft and bearings depends on the surface hardness. In order to achieve the surface hardness, these steel components are subjected to a type of quench hardening heat treatment process. There are several heat treatment processes available for the industrial application to improve the mechanical properties of the final part. Case hardening using induction heating is one of the widely used industrial techniques for improving the surface microstructure of a steel component. It consists of two stages i.e. induction heating cycle, followed by quenching in a fluid medium (usually water or oil)"

Jan 1, 2012

By S. N. Lekakh

Phosphorous segregated at grain boundaries during solidification and heat treatment dramatically decreases low temperature toughness of precipitation hardened Fe-Mn-Al-C austenitic steel. A thermodynamic analysis was performed to evaluate the possibility of decreasing P and subsequent segregation by Ca- and Ce-additives in the melt. It was shown that the predicted probability of forming a P containing compounds depends on melt composition and treatment sequence. Experimental heats were performed and several micro- and macro-structural effects of Ca- and Ce-additives were recognized by using an automated inclusion analysis technique.

Jan 1, 2010

By Gábor Csicsovszki

We have developed a novel method - at the laboratory scale - comprising an ion-exchange separation and a membrane-electrolysis step for the purpose of zero-waste regeneration of spent HCl pickling liquors originating from hot-dip galvanizing of common steels. It is aimed at the parallel regeneration of HCl and iron. Experiments revealed that iron can be electrodeposited at high current efficiencies by maintaining the following conditions: 0.04-0.08 M HCl, 500-1000 A/m2, 20°C and stationary electrolyte in a conventional cell. Zinc in the solution did not disturb the deposition of iron, however it contaminated the product and it poisons the anion-exchange membrane required to tackle acidity during electrolysis. For a preliminary separation, anion-exchange tests were carried out to produce pure iron solutions. Beyond the equilibrium studies, column experiments were carried out showing that low flow rates of the loading solution and the ~1.5 M HCl eluent are essential for separation.

Jan 1, 2006

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By Pengfu Tan

The control of converter slag chemistry and slag viscosity has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been used to predict the chemistry and viscosity of converter slag. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on slag viscosity, liquidus temperature of converter slag and skimming operation has been discussed. Some applications of the industrial operations have been presented.

Jan 1, 2006