Search Documents

By Tanm Engin, Ali Riza Tarakcilar, Derya Dispinar

"Nowadays, the casting industry is developing parallel with the information technologies (IT). Particularly the casting simulation software is being frequently used in foundry floors for casting quality control and optimisation. In this study, the filling and solidification analysis of a rolling roll manufactured by spherical graphite cast iron were carried out by Vulcan casting simulation software. The appropriate defect relieving suggestions were presented by anticipation of defects that may form during the casting process.IntroductionThe optimisation of a casting process has long been the most focused area in manufacturing plants. Many of the work involve not only the process itself but the cost as well. When it comes to the process, it is important to be able to control the defects that may form during casting.The casting process begins with the melting of a charge; followed by pouring into the mould cavity. One of the most important factors is the difference in the liquid/solid density which may lead to porosity. On the other hand, turbulence during filling is another significant factor in casting operations [1].During solidification, due to the density difference between liquid and solid, porosity might form which leads to crack-like defects. There are several other factors that may determine the quality of a casting such as segregation, inclusions, grain size and etc. However, porosity is one of the first parameters that can be easily determine and controlled by the help of simulation software. Simulation is a cost-effective tool in the optimization of process parameters and castings can be visually observed. Time loss and economic expenses could be minimized [2]."

Jan 1, 2012

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Samuel Senanu, Benjamin Agyei-Tuffour, Lifeng Zhang, Eivind Øvrelid, Adegboyega Nathaniel Femi

"The solar grade silicon ingot produced from directional solidification process usually pushes the impurities to the top and finally cut off and discarded, which leads to material loss. The hard inclusions lead to wire breakages during the cutting of the ingot in wafers. The main kinds of inclusions found in solar grade silicon have been investigated using vacuum filtration: needle-like Si3N4 and lumpy SiC inclusions. Clusters of SiC inclusions and Si3N4 are also found. Surface observations of the scraps before polishing reveals that Si3N4 inclusions are usually bigger and in some cases can be about a few millimeters. SiC inclusions are usually smaller, ~200µm but can be ~500µm in some cases. Inclusions observed after filtration are mainly SiC with diameters ~10µm. Through the vacuum filtration, 99% inclusions can be removed 99%. The possible mechanisms of filtration are cake filtration for the larger sized Si3N4 and SiC inclusions and deep-bed filtration the SiC inclusions. For the directional solidified silicon ingot, an approximate distance of ~10mm gave an encouraging cutoff thickness. The inclusions sizes were below 10µm. Introduction The search for an alternative source of energy to fossil fuel has led to a dramatic increase in the demand for solar energy due to its high dependability (abundant in nature) and environmental friendliness 1). During the last 5 to 10 years, the annual worldwide production of solar cell by the photovoltaic industry has increased to an annual rate of 30 to 40 percent 2). A necessary condition for the maintenance and even an increase of this growth rate is a decrease in the cost of feedstock for the solar cell production 1). The total international production in 1997 was 130 MW worth more than $500 million. In 2004 the consolidated world total production of PV cells increased to 1146 MW or around. $7 billion (Figure 1) 3). Silicon is currently the most dominant semiconductor material used in the PV industry. As shown in Figure 2 3), solar cells consist of two types of material, often the p-type and n-type silicon. Light of certain wavelengths are able to ionize the atoms in the silicon (causing atoms to either gain or lose electrons) and the internal field produced by the junction separates some of the positive charges (“holes”) from the negative charges (electrons) within the photovoltaic device. The holes are swept into the positive or p-layer and the electrons are swept into the negative or n-layer. Although these opposite charges are attracted to each other, most of them can only recombine by passing through an external circuit outside the material because of the internal potential energy barrier. Therefore if a circuit is made, power can be produced from the cells under light because the free electrons pass through the load to recombine with the positive holes."

Jan 1, 2008

By Brajendra Mishra, Mark L. Strauss, Gerard P. Martins

Europium is a critical material required for LED, florescent lamp, cell phone screen, and flat panel display production. This process recycling europium from waste lamp phosphors is an innovative method to supply europium. The selective reduction and precipitation method using sulfate precipitation is investigated to recover high-purity europium from yttrium-europium mixed solutions.

Mar 1, 2017

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

As a result of the consumption and the rising cost of raw materials for ironmaking, steel producers have increased their utilization of low-cost, low-grade raw materials such as high alumina iron ore. The effect of Al2O3 and the Al2O3/SiO2 ratio on the viscosity, surface tension and sulfide capacity of the CaO–SiO2–Al2O3–MgO–TiO2 blast furnace slag system were studied in the present work. At a fixed CaO/SiO2 ratio of 1.20, 9 mass pct MgO, and 1 mass pct TiO2, the viscosity increases with an increase in Al2O3 content at a range of 16–24 mass pct, and decreases when the Al2O3 is higher than 24 mass pct. Increasing Al2O3/SiO2 from 0.47 to 0.92 causes a slight decrease in viscosity of the slags and has an opposite effect when Al 2O3/SiO2 is more than 0.92. The surface tension increases with increasing Al2O3 content at a fixed Al2O3 content and Al2O3/SiO2 at a fixed CaO content. The desulfurizing capacity decreases with increasing of Al2O3 content, while increases with increasing Al2O3/SiO2 at a fixed CaO content.

Mar 1, 2018

By Daguang Lu

The section of sintering and BF (blast furnace) is very important in iron-making process. In practice, the scheduling is so extensive that three faults unfavorable to continuous product will be easier to happen. This paper introduces the integration Petri Net and GA (genetic algorithm) as suitable tools for simulation and optimization of scheduling to section of sintering- BF under a certain hot iron or-der. The situation of the iron plant Chongqing Iron and Steel Company is researched in approach above mentioned. By analysis, the conclusion is drawn that scheduling with optimized values can maintain continuity of key operations , can satisfy order of hot iron in maximal degree and can keep the best stability of key storages.

Jan 1, 2009

By T. Innmi

The potential of the nickel matte anode was measured during the matte electrolysis in the commercial cell. The slime layer consists of elemental sulfur and was found to greatly influence the potential of anode. The measurements of porosity and permeability of the slime suggest that the voltage drop of the slime layer dominates the potential. Furthermore, the diffusion of the electrolyte through the slime layer is also one of the factors to determine the potential. In addition, the copper content of the nickel matte anode was found to affect the change in the anode potential during the electrolysis. The role of copper on the anodic dissolution of nickel matte is discussed in this work.

Jan 1, 1988

By Luis M. González, Guzmánm Guillermo D., Davis Juan C.

"The Teniente converter (CT) of the Ventanas Smelter and Refinery of Codelco-Chile has two tuyeres for dry concentrate injection directly into the melt.The diluted phase injection system can feed 15 to 20 kg of concentrate for 1 kg of air, which creates a very abrasive solid/gas phase. The tuyeres commonly used lasted for about 3.5 days due to the accelerated decay of the shell, and 1.5 hours were necessary for the replacement of new ones in the reactor.Tests were carried out with common shell tuyeres with a tungsten based welding cover, and a life span of 28 days was reached, increasing the Teniente converter operational continuity between 1.5 to 2 %."

Jan 1, 2009

By Hugo Cabrera-Real

This work investigated the chemical and mineralogical properties of CaO-SiO2-CrOx-CaF2- MgO slags. Synthetic slags were prepared and the effect of the slag basicity (CaO/SiO2) and MgO contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that in slags with CaO/SiO2 = 1, the main Cr-compound was MgCr2O4 spinel, which forms octahedron crystals. Small amounts of CaCr2O4 and CaCrO4 were also observed. It was found that increasing the slag basicity from 1 to 2 the compounds MgCr2O4 and CaCr2O4 were formed together with the Cr(V)-containing compound complex Ca5(CrO4)3F which forms hexagonal crystals. The results showed that the highest chromium concentration levels in the leaching liquors corresponded to slags with CaO/SiO2 = 2, probably owing to the formation of Ca5(CrO4)3F.

Jan 1, 2010

By Jae-Chun Lee, Jinki Jeong, Manis Kumar Jha, Divika Gupta, Pankaj Kumar Choubey

Rare metal indium (In) is mostly used as electroluminescent material in liquid crystal displays (LCD) monitors. Present paper describes leaching studies for the recovery of In from waste LCD monitors in presence of different other impurities. The leaching studies showed that more than 85% of In was leached out using 20% sulfuric acid at 60oC in mixing time 30 min at fixed pulp density 25 g/L. The solution could be purified using SX/IX and from the pure solution metal/ salt could be produced by evaporation, precipitation, electrolysis, crystallization processes.

Jan 1, 2014

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Hongmin Zhu, Guihua Wang, Xiangsheng Wang

"The anode process of carbon electrode in fluoride melt was studied by voltammetry and chronoamperometry. Anode gases were analyzed by gas chromatography on-line during controlled-potential electrolysis. Two peaks were observed on the cyclic voltammograms. According to the results of gas chromatography, the first peak was corresponded to the discharge of residual oxide ions, with the formation of CO and CO2. Discharge of fluoride ions occurred at 4.1 V vs. Li+/Li, and leading to the anode effect. With the occurrence of anode effect, small amount of CF4 was detected. As the potential reached 4.5 V, CF4 and C2F6 gas evolution occurred, and the current increased to form the second peak.1.IntroductionIn the primary production of Aluminum and some rare earth metals like neodymium, a departure from normal cell operation known as anode effect results in the generation of perfluorocarbons (PFCs), which have high global warming potentials [1]. Owing to the pressure of environmental protection, considerable research has been carried out to clarify the mechanism of anode effect and PFC generation of industry and laboratory cells in the aluminum electrolysis system [2-9]. The common result on PFC generation is that the PFCs are emitted from Hall-Heroult cells only when they are on anode effect. In this article, we selected LiF, the main electrolyte for the neodymium electrolysis [10-11], to perform further investigation on the underlying kinetics of PFC generation and the nature of the reactions at the electrode.2. ExperimentalAll experiments were carried out in an alumina tube reactor, which was filled with high purity helium atmosphere. Spectrographic graphite crucibles were used, which played the dual role of molten fluoride container and the counter electrode. Lithium fluoride was analytical grade. The experiments were carried out at 900 °C."

Jan 1, 2011

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By R. Cameron

The growing use and acceptance of electric vehicles (EV), as evidenced by the record sales of over 750 thousand vehicles in 2016 and a current global EV stock of 2 million vehicles, is putting pressure on sourcing raw materials such as cobalt, and to a lesser extent, nickel. Global supply is poorly diversified, with 50– 60% of global cobalt production sourced solely from the Democratic Republic of Congo (DRC). One potential source for cobalt and nickel are low-grade nickeliferous pyrrhotite tailings, of which 50–100 million tonnes are present in the Sudbury area alone. This paper presents the extraction of cobalt and nickel from this material using a combination of flotation and bioleaching technologies. The findings of a high-level techno-economic analysis of the proposed processing flowsheet are presented.

By Ahmet Haxhiaj, Bajram Haxhiaj

Based on the placement of lead and its consumption in industry branches, the paper deals with the composition of lead in the massive of Kopaonik. Removal, tenuity and grinding of galenit. The paper in particular treats the flotation process, and also treats physico-chemical bases of reagents in the process, as well as decanting, drying, filtering and storage of concentrates. Verification of the chemical composition of Pb concentrates with Pb, Zn, Bi, As, Sb, In, Au, Ag, etc. It is special that in Kopaonik massive the ratio of Pb: Zn composition is 1.4:1.0 and during the flotation lead is inclined to go with pirotines concentrate more than is allowed. We are strongly focused to maximally decrease the Pb amount that goes with pirotine concentrates and wastes. The paper as such gave the first effects in optimizing of these parameters with positive effects in flotation process in Trepca.

Mar 1, 2018

By Laura Angeles, Martin Reyes, Ivan Reyes, Miguel Perez, Francisco Patiño, Mizraim Flores, Elia Palacios

Chemical and mineralogical characterization of a sulphide ore from the mining district of Zimapan, Hidalgo, Mexico, was performed in order to obtain accurate information on the composition of the ore to optimize the subsequent flotation process. A combination of techniques was used: Scanning Electron Microscopy (SEM) with Energy Dispersive Spectrometer (EDS), X-ray diffractometry (XRD), Inductively Coupled Plasma (ICP) and Fourier transform infrared spectroscopy (FTIR). The SEM mapping confirmed the presence of the elements: Ca, Si, Fe, K, S, Al, Zn, Mg and Mn. The XRD analysis suggests that the ore matrix is calcite; additional species found were wollastonite, johannsenite, and pyrite, among other impurities. The FTIR analysis performed for the aqua regia insoluble showed the presence of calcium oxide, copper oxide and silicon oxide. The results for the ICP analysis were:13.31% S, 2.55% Fe, 0.46% Zn, 0.03% Cu, 0.06% Pb, 0.07% Mn, 0.09% As, 0.01% Sb and 0.08 grton-1 Ag.

Mar 1, 2017

By Hiroshi Maeta, Takao Kino, Hirota Osono, Kikuo Matsusaka, Azusa Shida

"Prior to refine an ultra-high purity material, it is necessary to estimate the surface cleanness of a base material. In this report, the cleaning method of a surface for refining of an ultra-high purity aluminum has been studied. Aluminum sample of 99.999% purity was p9lished mechanically and electrically and washed with various solvents. Surface composition and a depth profile near the surface were examined. Based on the experimental results, surface structure of an ultra-high purity aluminum was discussed.IntroductionRecently, studies on high purity metals have become of interest, and we have reported .various properties of an ultra- high purity aluminum1- 2)In order to purify a metal, it is necessary to clean a work area and to make vacuous as possible. So, we are studying the purification of aluminum by an ultra-high vacuum refining system and a zone refining system set up in a clean room with cleanliness class of 1000.Now, in order to avoid a mixing of impurities into the refining metal, a surface cleanness of a base metal is very important factor. The purity of the base aluminum used our work is 99.999%, but the surface state of the base aluminum is not clear. Aims in this work .are to investigate the surface state and to obtain the cleaning method of the base aluminum.Experimental procedureSamples used in this work were 99.9% (3N), 99.99%(4N) and 99.999% (SN) aluminum produced industrially and 99.9999% (6N) aluminum purified by us."

Jan 1, 2000

By C. Wieckert

Concentrated solar energy can be used as heat source for the production of metals. One of the most promising respective processes, the solar carbothermic production of Zn from ZnO, is investigated within the European research project SOLZINC, a cooperation of institutes and industries from France, Germany, Israel, Sweden and Switzerland. The solar produced Zn can be used as commodity or as an energy carrier for further processing on demand to electricity in Zn-air fuel cells/batteries or to generate hydrogen by reaction with steam. In both cases the Zn is oxidized to form ZnO, which can be recycled back to the solar plant. In these cyclic processes Zn acts as a means to store and eventually transport solar energy. Second product of the solar process step is a CO-rich offgas, which may e.g. drive a gas engine or may be shifted to hydrogen in a conventional reaction with steam. A pilot plant using 300kW concentrated solar power input has been constructed and operated successfully. 86mass-% of ZnO mixed with 14mass-% of charcoal are reacted to produce Zn and CO at a temperature of about 1200°C, yielding about 50 kg gaseous Zn per hour. Zn-dust with 95% purity is recovered from the offgas system that was designed to produce Zn for Zn-air fuel cells. Based on the results and findings from the pilot plant, a two tons Zn/h solar demonstration plant has been designed conceptually. Cost studies have been performed and scenarios for producing electricity or H2 via these ZnO/Zn-cyclic processes are evaluated.

Jan 1, 2006

By W. D. Riley

Engineered Scavenger Compounds (ESCs), developed by the U. S. Bureau of Mines I are a novel class of compounds that can selectively recover a desired element from 'a solid or molten alloy. Lithium titanate (Li2Tip7 or Li20' 3TiO.) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (AI-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both of the structures are metastable, the hexagonal phase that forms during the scavenging of Li from AI-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electtodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li.Til07 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1991

By Anurag Tripathi, J. K. Saha, S. K. Ajmani, J. B. Singh

"The quality of steel is a major concern in the metallurgical industry. The control of liquid steel temperature can enhance the level of cleanliness in steel. Ladle is one of the major vessels used to transfer liquid steel between different stations. The heat transfer phenomenon taking place in this vessel needs to be monitored for controlling the liquid steel temperature. A CFD model was developed for prediction of liquid steel temperature during complete process cycle of ladles in direct heats. The model was validated with liquid steel temperature measured at on-line purging station and tundish during teeming from one of the actual steel plant. The accuracy of model was 96 %. The results obtained show insignificant effect of slag thickness, tapping temperature and ladle life on liquid steel temperature in the ladle. However, the importance of initial refractory temperature was noticed. The CFD model developed in present work can generate the thermal history of liquid steel and refractory walls of any ladle at any stage.1. IntroductionThe control of liquid steel temperature is desired to achieve required steel quality. The low casting temperature is detrimental and may result in nozzle blockages due to premature solidification in the tundish. The phenomenon of heat losses taking place in ladles needs to be understood for prediction of liquid steel temperature. The assessment of thermal profile of liquid steel from BOF converter to caster can be done through consideration of heat losses at all points. Hlinka and Miller [1] showed that the ladle pouring temperature varies due to heat losses from molten steel into surrounding refractory layers. The phenomenon of thermal stratification was numerically simulated by Ilegbusi and Szekeley [2]. The effects of slag cover on heat loss and liquid steel flow in ladle before and during teeming to a continuous casting tundish was numerically simulated by Chakraborty and Sahai [3]. Investigators also developed some simple models to predict the steel temperature for some of the processes taking place in ladles [4-9].The present work is an effort to generate the full information about the temperature drop taking place in any ladle throughout its process cycle. This information can be used to predict liquid steel temperature and to take decisions to minimize heat losses."

Jan 1, 2012