Search Documents

By Marcelo Jimenez Bustos

The Chagres Smelter was the first in Chile to follow environmental regulations to control sulfur dioxide emissions. Because of this, the operation and development plans have had to incorporate environmental planning as part of its policies for almost three decades. The present article shows the development of the environmental standards applied to its operations, investments and operational improvements carried out to meet the regulations and improve competitiveness. Results to-date and future plans are outlined, as well as their impact on operations and the environment.

Jan 1, 1993

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By Bing Song, Fei Xi, Xuewei Lv, Kai Zhang

The electric arc furnace process is a common method to produce high TiO2 slag from ilmenite. The pre-reduction process was proposed in recent years in order to reduce electricity consumption. In order to enhance the pre-reduction degree, high energy ball milling was proposed to improve the specific surface area of the ilmenite prior to reduction. In this study, the carbothermic reduction behavior of milled ilmenite concentrate was investigated. It was found that the ball milling method can result in a higher reduction rate and improved metallization of iron. The metallization of iron increased with increasing the time of ball milling. The metallization of iron with milling reached 89.49% when the time of ball milling was 70 min., while the FeO content decreased with 70 min. of milling from 11.84% to 4.76%.

Jan 1, 2014

By T. H. Eyde

Several hundred natural zeolite deposits occur in Tertiary and Cretaceous age formations of the western United States. Most of the large deposits are altered vitroclastic tuffs. Many of these deposits consist of a matrix of a high purity zeolite mineral or minerals in which fragments of unaltered rock are imbedded. These deposits represent an extensive resource of zeolite minerals which can be beneficiated to a consistently uniform, high quality product. The beneficiated natural zeolite products will possess many advantages over the selectively mined, unbeneficiated natural products currently being produced. These advantages will include: uniform particle size, high purity, consistent quality, high brightness, low iron content, high attrition resistence, uniform cation exchange and adsorption capacities, and low price.

Jan 1, 1981

By B. Wasmund, K. Adham, K. O'Keefe, C. Lee

"Metal chlorides (e.g. iron and nickel) can be pyrohydrolysed at elevated temperatures to yield an HCl rich off-gas and a metal oxide product. Typically, the high energy requirement for pyrohydrolysis is provided by the combustion of a hydrocarbon fuel with air. Here, it is demonstrated that the use of oxygen-enriched combustion can result in lower fuel requirements and higher HCl concentrations. In addition, the oxygen enrichment can result in a smaller volume of off-gas and thus, smaller and less expensive process equipment. This new concept can be applied to both the spray roaster (SR) and the fluidized bed reactor (FBR). Similar to the aircombustion case, the oxygen-enriched process can use a direct contact venturi scrubber, to recover energy from the roaster off gas, but at a higher efficiency. The new process also uses an absorption tower for capturing HCl from the roaster off-gas, but generates a stronger HCl solution than is possible with pyrohydrolysis in air.BackgroundIn recent years, the metallurgical industry has become increasingly involved with developing methods for extracting metals, upgrading products or cleaning metallic products by using hydrochloric acid. These applications of chloride metallurgy often result in metal chloride solutions, which should be processed to regenerate HCl for reuse, and to recover the metal value as a product or by-product oxide [2, 3, 4].The pyrohydrolysis of metal chloride solutions has been done in two types of air roasters: spray and fluidized bed. The existing roasters burn a hydrocarbon fuel in air, to provide the required energy for evaporating the feed solution and to provide an elevated temperature for the chloride pyrohydrolysis to occur, according to the following reactions:"

Jan 1, 2011

By Mokka Rao, Arturo Valles, Jose Rodríguez

"This paper shows a mathematical model based on finite elements, applied to bottom poured shell ingots of C.V.G. Sidor Plant. The model was used as a strategy to determine the thermal effects that are produced when solidification conditions are modified without interfering with the production process. The modification consisted of placing a thermal insulator on top of mould.The results obtained by the model indicated that the solidification time increases with insulator on base of the mould. With these results a significant number of casts were run with and without insulator. Latter by means of a metallurgical analysis it was determinated that the ingots cast with insulator reduce the level of non-metallic inclusions and the presence of internal blistering in seamless pipes.IntroductionThe process of fabrication of seamless pipes in SIDOR involves various steps of processing, such as heating the ingots, fabrication of the prelaminated, fabrication of the bored pipe, lamination of the pipe by passing through the pellegrine mill, heating the pipe in a walking bean furnace and final calibration through a calibrator mill. The material utilized for producing these pipes is provided entirely from a electrical arc furnace and casted ingots, especifically, from the superintendence of bottom pouring.The process of bottom pouring consists of positioning twelve moulds of diameters 415, 480 or 505 mm over a plate of grey cast iron in which exists a system of communicating vessels. The ingots are distributed around a central duct from which the steel flows down and filling gradually, each one of the moulds (Fig. 1)."

Jan 1, 1997

By Henrlk Gripenberg

To solve the environmental and financial problems of the traditional Rotary Salt Furnace process, a new salt-free method for aluminum dross and scrap melting, ALUREC, has been developed by AGA and its partners, Hoogovens Aluminium and MAN GHH. AGA and Hoogovens Aluminium developed the main process concept and jointly carried out trials on pilot plant scale. Owing to excellent results" the partners decided to jointly erect a commercial scale test plant. The order for the design and erection of the furnace went to MAN GHH. The three companies designed the test plant and began operation in the spring of 1994. The results have been excellent and the process is expected to be a technical and commercial success.

Jan 1, 1995

By O. Chemezov, Yu Zaikov, A. Apisarov, A. Isakov

"Silicon deposits containing 99,9 wt.% of main component were obtained by SiO2 electrolysis from chloride-fluoride melts. The operating temperature was varied from 973 up to 1073 K. The conditions for obtaining crystalline fibrous micro- or nanodeposits were determined. The deposits were investigated by ESM methodIntroductionThere are large reserves of natural quartz of high purity in Russia. Processing of this raw material by electrolysis in molten salts produces silicon containing 99.9 weight percent of basic substance.[1]This method is less energy-consuming in comparison to existing methods for producing high purity silicon from gas phase.Another advantage of the electrolytic method for producing silicon from its oxide in molten salts is the possibility of production of high-purity silicon under air atmosphere. It dramatically reduces costs of the electrolytic cell construction, and the operating costs at electrolysis.On our opinion, the main advantage of the electrolytic production from SiO2 in molten salts is a unique opportunity to obtain micro-and nanostructures of silicon deposits. In particular, it is possible to obtain fibrous structures of silicon. The electrolytic method allows smoothly adjusting the thickness and length of silicon micro- and nano-wires by varying the cathode current density and temperature of the process."

Jan 1, 2012

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Drew Sinha

Success of the environmentally benign semiconductor manufacturing depends on the cost-effective integration of the principles of reduce, recover, reuse and recycle from source material to final product disposal. Increasing demand combined with current shortage of polysilicon provided unique opportunities to recover the silicon waste, caused by various defects, in wafer manufacturing process. Current practices relating to recovery and reuse of waste silicon produced, from crystal growth process to finally polished and epitaxially deposited silicon wafer, at Mitsubishi Silicon America is presented. Future plan to recycle the process generated silicon fines produced during the intermediate steps of the wafer manufacturing process such as grinding, slicing, lapping and polishing is also discussed.

Jan 1, 1998

By Robert E. Moore

Renewed interest in olivine refractories has led to efforts to characterize them employing modern techniques of experimentation and data analysis. Initial studies have focused on determination of physical and thermophysical properties. Special equipment for the determination of thermal shock resistance and creep behavior have been constructed. Optimal compositions for maximizing various properties are being identified using appropriate statistical techniques. The overall goal is to develop response surfaces for each of a selected group of engineering design and use properties. Development of ?olivine Refractories? in the United States The term "olivine refractories" is used here because it does appear that domestic deposits of this rock will be the focus of renewed interest and "olivinell is the preferred term in this country. There are extensive deposits of high quality olivines extending through parts of Georgia. North Carolina and in the state of Washington. The eastern olivines are much more localized and extensively altered compared to the western materials. The Washington olivines exist as massive rock deposits in the Twin Sisters mountain area northeast of Seattle and their inaccessi-bility has slowed efforts to develop them. The North Carolina olivines have been used in steel plant applications since the 1930&apos;s. Geologists use the term "olivine" to describe assemblages of ortho-silicates. 2RO.SiO2, wherein the RO may be MgO. FeO. MnO. etc. When the RO consists essentlally of MgO and FeO. the material is called dunite and. as such, is synonymous with "refractory olivine." Refractory olivines utilizing North Carolina materials were developed for brick products by Birch and Harvey in this country around the mid-1930&apos;s. (I) Their work was completely independent of that of V. M. Goldschmidt and co-workers who used massive dunites located in Denmark. (2) These deposits are currently being mined by A/S Olivine of Denmark for the manufacture of a rather complete line of brick shapes for use in steel-plant. glassplant. and cement kiln applications. Birch and Goldschmidt

Jan 1, 1982

By Chuanlin Fan

The process of flotation separation and recycling of spent potlining (SPL) was described. On the basis of the laboratory investigations, the effects of influencing factors in froth flotation process, such as grain size, flotation agent dosage, pH value, pulp density, and dissolved components concentration, etc, were carefully studied. And the influence on environment of the process was also discussed. It was found that flotation separation can be used as an environment-friendly method for treatment of SPL residue. Carbon and other compounds (include cryolite, sodium fluoride, calcium fluoride and diaoyudaonite, etc.) from SPL were separated and recycled as flotation products respectively.

Jan 1, 2009

By Q. Cao, A. Pitts, L. Nastac

Accurate prediction of the desulfurization behavior of steel is of great importance for process control during ladle metallurgical furnace (LMF) steel refining. A CFD model capable of simulating multiphase flow with bulk and free surface turbulence phenomena and desulfurization behavior in the gas-stirred ladle has been developed. The fluid flow behavior shows that slag and metal try to entrap each other, forming a two-phase mixing zone. The resulting substantial contact area between the two phases will provide very favorable kinetic conditions for chemical reactions. For reaction kinetics model, the reactions at the metal/slag bath interface as well as the entrapped droplet surface are included. Predicted results show that the sulfur content changing with time in the ladle agrees well with the industrial-scale experimental measurements.

Mar 1, 2017

By S. Neven

The smelting of copper anode slimes, a material which contains mostly lead, silver, copper and selenium, has been practiced for many years with a view to recovering the silver and associated small amounts of gold. However, a theoretical understanding of the process has been lacking and this handicaps efforts to improve and intensify smelting operations. In the past few years work has been done in this area and this work will be reviewed in the paper. The underlying thermodynamics of the oxidation of silver-copper selenide mattes has been developed and used as a basis for the construction of a computational thermodynamics model which attempts to predict the composition of all condensed phases during the course of smelting. The model will be outlined and its successes in matching experimental data, as well as its current deficiencies, will be considered. Supporting work on the thermodynamics of silver solubility in slags, on activity-composition relationships in the Ag-Se system and work in progress on the oxidation state of copper in the slags will be reviewed. These projects are designed to provide further detailed data which will improve the robustness of the thermodynamic model.

Jan 1, 1999

By Jafar Safarian

A new kinetic modelling technique has been applied to study the rate of MnO reduction from slags by dissolved carbon in liquid iron. Based on a consideration of the fundamental reaction kinetics, a general differential equation for the slag reduction process has been formulated, which then is solved analytically for certain special cases. By re-writing the solutions in a dimensionless form the poorly known kinetic constants are eliminated, which makes the model both flexible and applicable to a wide range of experimental conditions. For example, changes in process parameters such as temperature, metal composition, slag composition, gas composition can readily be captured along with variations in the crucible geometry. Based on a comparison with a series of experimental reduction curves being reported in the literature, it is concluded that the predictive power of the model is surprisingly good, yielding outputs that are both reliable and physically reasonable. An attractive feature of the model is that it provides an alternative way of calculating the activation energies from experimental reductions curves. For example, it suggests that the activation energy for the reduction of MnO by dissolved carbon in liquid iron is about 90 kJ/mol, which is different from the previously reported activation energies. The model also suggests that the crucible geometry, which affects both slag the volume and the resulting slag/metal interfacial area, has a significant influence on the overall reduction kinetics. This design parameter is a key to further optimisation of the process on an industrial scale.

Jan 1, 2006

By A. V. Tarasov, V. M. Paretsky

"Based on theoretical and experimental studies into the specific features of the mechanism, kinetics, aerodynamics and heat transfer parameters of the flame-type oxidation of metal sulfides in a stream of technical-grade oxygen, a three-dimensional deterministic mathematical model of an oxygen-flame smelting furnace has been developed on the basis of the zonal method for computation of heat exchange. The model is presented in the form of equations taking into consideration the radiation component of the selective radiation, the convection component of mass transfer between the space and surface zones, heating of charge particles due to heat conductivity, accretions formation on a multi-layer refractory lining with inserted cooling elements. The adaptation of the model for a full-scale furnace has demonstrated the possibility for its use for computation of main smelting process parameters. Multifactor model investigations were conducted and the results obtained were applied using statistical methods for development of a simplified computational regression model describing the interrelation of the main output parameters: temperatures of flame, lining, slag and off-gas; heat fluxes to the lining; thickness of accretions; heat removed by cooling elements; copper content of matte. On the basis of this model, a block diagram of the algorithm was developed for control of the thermal conditions of the furnace, as well as the control algorithm itself.IntroductionThis paper presents the results of an integrated modeling and development of principles for control of copper smelting process using as an example the oxygen-flame smelting process (KFP) for treatment of sulfide concentrates at the Kovoguty Krompahy copper smelter (Slovakia) with a capacity of 20,000 tpy of copper."

Jan 1, 2001

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994