Search Documents

By Zhigang Liang

Investigation into the mixing of 150t ladle furnace by two-nozzle jetting was performed by a water model simulation of 1:4. The effects of nozzle arrangements including separation angle, radial position and asymmetry as well as tracer adding position on the mixing time were studied. The most favorable mixing is achieved when the two nozzles are symmetrically arranged at half radii in the ladle, with 45o separation angle. The empirical relationship between the mixing time and stirring power intensity has been established for two-nozzle jetting based on the present experimental results. In addition, the swelling above bath surface is also investigated with two-nozzle jetting.

Jan 1, 2009

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By Fuming Wang, Lifu Hu, Changrong Li, Ruipeng Pang

The solidification structure of 430 ferritic stainless steel has been calculated in the solidification process by using 3D-CAFE model under the condition of water cooling. The calculated results consistent with those obtained from experiment. Under watercooling condition, the solidification structure consists of chilled layer, columnar grain zone, transition zone and equiaxed grain zone

Jan 1, 2015

By Egil Aukrust

"An American Iron and Steel Institute Task Force evaluated developing direct steelmaking technology worldwide to seek a replacement for the coke-oven, blast-furnace, basic-oxygen process technology now in use. To remain internationally competitive it is essential to move away from the traditional series of batch processes towards continuous processing and the associated energy savings which are possible with high technology process control systems. The group identified in-bath smelting of iron ore pellets or fines with coal as the process most sui table for domestic raw materials (including abundant scrap) and called for research to study operation with varying degrees of preheat and prereduction of the ore by the gases generated from the coal and various degrees of combustion of these gases above the melt.A coordinated, 3-year, $27 million, direct steelmaking research program is proposed. Concurrent projects include design, construction, and experimental operation of an in-bath smelting pilot plant; modeling, simulations, and laboratory-scale experiments at universities on slag-phase and metallicphase reactions and interactions; and large-scale heat transfer and reaction rate trials. Also included are modeling studies and pilot plant trials of on-stream decarbonization and desulfurization; application of circulating fluid bed technology to fine ore reduction and hot gas cleanup; and specific heat transfer and fluid flow research projects.IntroductionThe American Iron and Steel Institute (AISI), based on the Task Force studying direct steelmaking, believes strongly that a coordinated program of research on the reduction of domestic raw materials to liquid steel should be undertaken as part of the Steel Initiative program. To specify the steelmaking process for development best suited to the American steel industry and domestic raw materials, it was important to determine the state-of-the-art of direct steelmaking worldwide, both as practiced and under development, and then, by expert analysis of the processes and their potentials, to choose the process most likely to provide a domestic competitive edge."

Jan 1, 1988

By Beatryz Mendes, Leonardo Pedroti, Afonso Azevedo, José Maria Carvalho

The dregs is a waste from the cellulose production, and its reuse is an effective way to reduce environmental impacts. Researches have already been done to incorporate it into building materials. The present work aimed at incorporating dregs in the production of mortar to replace hydrated lime. The methodology adopted was the Simplex network with ten sampling points, varying the amount of cement, sand, and dregs. Each mix was submitted to flexural strength, compressive strength, apparent mass density and water absorption by capillarity tests. The results were analyzed by the software Minitab, obtaining the influence of each component in the mixture. The best results were observed in mixes with a higher proportion of cement and less of residue when it was analyzed the flexural and compressive strengths. Larger rates of apparent mass density and water absorption were noticed with a greater amount of dregs. The experimental design also allowed the obtainment of mixture ratios from predetermined values of the tested properties and indicated that the addition of dregs in mortar could be an alternative to civil construction.

Mar 1, 2018

By Zhao wen Wang, Ramana G. Reddy, Min Li

"The electroreduction of Co(II) in l-butyl-3-methylimidazolium tetrafluoroborate (BMlMBF4) ionic liquid was investigated by cyclic volatrnmetry at 353 K. The results show that the reaction of Co(II) to Co is irreversible in one step with two electrons transferred. The diffusion coefficient of Co(II) was estimated to be 7.6 x 10-8 cm2 s·1 at 353 K. Then the electrodeposition of cobalt was studied at different cathodic potentials (-0.80 to -0.95 V) and different temperatures (333 to 363 K) in BMIMBF 4 containing 0.20 mol L-1 Co(BF4)z. The deposits were characterized using scanning electron microscope (SEM), energy-dispersive spectroscopy (EDS), and X-ray diffraction (XRD). SEM images show that a uniform, dense, and compact deposit was obtained at -0.80 V and 333 K. The deposits were identified as high-purity metallic Co for all experiments by EDS and XRD.IntroductionCobalt is known as a hard magnetic material and cobalt alloys have been shown to have excellent magnetic properties with adequate mechanical durability and corrosion resistance, which are needed for high performance magnetic recording applications [1-4]. The electrodeposition of Co alloy in the aqueous solution is generally difficult because of the narrow electrochemical potential window of water, which leads to the low current efficiency and worse quality of deposits due to the hydrogen embrittlement. Thus, aprotic ionic liquids (ILs) are expected to be the ideal alternative media for electrodeposition of cobalt or its alloy since ILs usually provide a wide working potential windows, negligible vapor pressure, and acceptable conductivity for electrolysis without the occurring of hydrogen evolution [5, 6]."

Jan 1, 2014

By Donggen Fang, Liu Xuan, Jilai Xue

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO 4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By Caryn Wendt, Donna Post Guillen, Armando McDonald, Erik R. Coats, Chaston Ellis, Kevin Feris

Dairy operations constitute ~2.5% of annual U.S. greenhouse gas (GHG) emissions, making dairies one of the largest sources of industrial GHG emissions. We are developing a novel, integrated system to achieve a net reduction in dairy GHGs while producing value-added materials and products. This integrated manure-to-commodities system converts dairy manure to bioenergy, sequesters carbon by converting volatile fatty acid-rich fermenter supernatant to bioplastics, and utilizes anaerobic digester (AD) and polyhydroxyalkanoate (PHA) reactor effluents to produce algae that can be harvested and internally recycled to enhance PHA production and sequester carbon. A decision-making tool is being developed for the integrated system that quantifies net GHG reduction, carbon sequestration, nutrient management and economics.

Jan 1, 2016

By T. C. Tseng

Austenitization is a critical stage in heat treatment of steels. The available kinetic data in reference to various initial microstructures are very limited, particularly at high heating rates. In this study, integrated experimental and computational approaches have been conducted to quantify the progress of austenitization and the attained microstructure. In particular, the study is concentrated on cementite and carbide dissolution in two steel grades. Various computational methods are developed to facilitate the study: (l) an algorithm for direct determination of kinetics data as well as progress of transformation from high-rate dilatometer tests; and (2) a suite of mesoscale computational models for particle dissolution, elements diffusion, mechanics, thermodynamic and the resulting kinetics of transfonnation. Critical exprimentation is carried out using advanced techniques in microstructure characterization, chemical analysis, and Gleeble thermal-mechanical simulator on specimens of well-controlled initial microstructures. Keynotes: Cementite, Carbite, Dissolution, Steels, Austenitization

Jan 1, 2003

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000

By M. M. Monte

A method for removing metallic mercury from contaminated tailing, using the flotation process, is described. In order to define some relevant parameters for the mercury flotation system, microflotation and electrophoretic mobility tests were carried out on (pure) metallic mercury in the presence of several surfactants. Based on the results obtained from fundamental studies a series of bench scale flotation experiments with mercury containing tailings from two wetland sites in Brasil were done. The results of microflotation tests with mercury showed that by using cetyl trimethyl ammonium bromide, an increase in mercury flotability is observed in the acid pH range, whereas in the presence of potassium oleate the highest mercury flotability was found in the alkaline pH region. The mercury flotability using potassium amyl xanthate was improved by the addition at sodium dithionate as an activator. The bench scale flotation tests with contaminated tailings from Poconé (brazilian wetland site) showed a recovery of 70% when sodium dithionate was used as activator and potassium amyl xanthate as collector. The resulting coefficient of separation is around 60%. However, the results of the flotation experiments with fine fractions from amalgamation tailings from Peixoto de Azevedo (brazilian wetland site) showed a low mercury recovery (32%).The results from this work suggest that since in the Poconé site tailings, the metallic mercury is not completely associated to the finer particles, the flotation process to recover the metallic mercury seems very promisor.

Jan 1, 1996

By Feng-guang Li, Rui Guo, Ju Zhang

Cooling stave is one of the most important equipment of blast furnace for iron making. The heat transfer performance and service life of the cooling stave, to a large extent, determines the efficiency and economy of the iron making process. In this paper, a 3-D heat transfer model of cooling stave was founded by ANSYS based on FEM theory, and the heat transfer characteristics of cooling staves which were made of different materials (cast iron, cast steel and copper) were analyzed. Then, several suggestions on choosing material of cooling staves were given according to the calculation results and the actual working conditions of the cooling staves.

Mar 1, 2017

By Ernest D. Mast

Noranda&apos;s Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter&apos;s productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By R. M. Lamya

A considerable part of gold encapsulated in some refractory sulphides can be dissolved during sulphide matrix decomposition in non-complexing aqueous media. This has been concluded from laboratory results of gold extraction from pyritic and arsenopyritic concentrate containing 172.8ppm Au, into 10% hydrochloric, sulphuric and nitric acids. The degree of sulphides decomposition in the non-oxidative acids limits the gold extraction from this specific concentrate to about 10%. In the case of nitric acid, the gold dissolution follows the rapid decomposition of sulphides, reaching 32 to 42% of extraction at almost total decomposition of the sulphidic minerals. Accumulation of gold in this acidic and non-complexing solution to several ppm was not affected by the soluble products of the sulphides decomposition. An attempt to explain this gold behaviour is undertaken and some practical implications are discussed. In the investigated concentrate the "soluble gold" is mostly associated with arsenopyrite. This is consistent with the latest findings of other authors that gold disseminated in arsenopyrite can occur as cation Au3+. In a comparative test the gold extraction into highly concentrated chloride solution, in the same oxidative conditions, amounted to 92.34%.

Jan 1, 1995

By F. Kassabji

This publication presents the main experimental and theoretical results on the recovery of aluminum scrap (dross and Used Beverage Can) without use of any addition of fluxing salts. Dross and UBC&apos;s processing experiments have been conducted in a rotary plasma furnace operating in the transferred and non-transferred mode, using different plasma gases. The investigation involved the treatment of more than 100 kg of dross and other aluminum residues using plasma torches with less than 100 kW power. The experimental work showed that this process is .far more economical and kind to the environment than the conventional route using a salt flux. An equilibrium thermodynamic calculation at elevated temperature makes possible the prediction of by-products at various temperatures for different plasma gases.

Jan 1, 1994

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By K. Krishnapisharody, G. A. Irons

"The modeling of gas-liquid plumes in steelmaking ladles has been the subject of many investigations. In most studies, the “modified” Froude number, based on the momentum of the injected gas, has been employed to characterize two-phase plumes. This approach has several shortcomings and is critically reviewed in the present work. Based on an extensive review of previous work and theoretical considerations, it is demonstrated that the injected momentum and consequently, the modified Froude number has no significance to gas blowing operations in Ladle Metallurgy. Instead, an approach based on the “plume” Froude number, previously shown by the authors as the proper form for Froude similarity, is extended as a simpler alternative.IntroductionGas injection is central to most Ladle Metallurgy operations. During ladle processing, the steel melt is usually stirred by an inert gas like Argon through porous plug(s) fitted in the bottom of the ladle or a lance inserted deep into the melt. The purging serves several purposes viz., homogenizing the melt, flotation of inclusions, enhancing the rates both of refining reactions and dissolution of alloying elements and promoting inter-phase interactions in the ladle.The topic of gas injection into liquid baths has been the subject of several investigations in the past. A great deal of this work, both experimental and computational, was devoted to describing the structure and properties of two-phase plumes as reviewed recently [1]. Generally, the ascending two-phase mixture is sub-divided into three distinct regions [2]: the jet core, transition and the bubble plume, respectively. The jet region, where the momentum of the injected gas is transferred to the bulk liquid, is also called the ‘momentum region’. In a similar manner, the plume is called the ‘buoyancy region’ where the motion of liquid is caused by the buoyancy force exerted by the bubbles. The proper characterization of these regions is important for the analysis and modeling of stirring operations in Ladle Metallurgy. Although many mathematical correlations exist for this purpose, some issues of theoretical and practical interest to the modeling of gas-liquid plumes need further attention."

Jan 1, 2012

By Liuyin Shi, Kang Liu, Fengqi Zhao, Yan Song, Zhiping Yang, Xing Fan

Due to the high energy consumption, long technical process, low usage rate of vanadium during the traditional smelting vanadium steel process, a new method for decarburization by CO2 to directly smelt vanadium-containing steel in blast furnace was proposed. In this paper, the thermodynamics of CO2 decarburization in molten iron process was calculated out by FactSage. The thermodynamic calculations indicated that in standard state, the transformation temperature of C and V was 1357 °C; the oxidation order of element was Si, C, V, Mn and S when using CO2 as oxidant. The experiment of blowing CO2 temperature showed that decarburization reaction temperature was 1550 °C, carbon content could be decreased to 0.676%, the decarburization rate was 88%. There was no effect on vanadium content in molten iron during the decarburization process, vanadium content was 0.323%, which meets the request of vanadium mould steel.

Mar 1, 2018

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013