Search Documents

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By Milton Manrique

The thermal decomposition of zircon concentrates in a non-transferred arc thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and zircon particle size was studied. Products were characterized by XRD, SEM, TEM and chemical analytical techniques. The average size of the product was in the submicron range. Free energy minimization plots were used to predict the behavior of the system under different operating conditions. A kinetic model to describe the different stages of the thermal decomposition process is proposed. The results of this investigation showed a significant segregation process where the zirconia-rich product is collected in the reactor while the silica-rich product is collected in the filter. TEM analysis indicated that silica vapor is condensed on the surface of the zirconia particles.

Jan 1, 1996

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997

By C. M. Iheagwara

An overview of the scope and ramifications of scrap recycling in the Nigerian metallurgical industries has been presented in this paper. The modern state-of-the-art processing techniques and the operational strategies employed in the recycling plants are discussed. Optimization techniques for cost effective recycling operations are highlighted. As new units within existing metallurgical plants and new metal working plants approach commercial operations, expansion of existing recycling plants and the emergence of new ones have been showing to hold the key to their profitability from the raw material standpoint. The present economic predicament of the entire industrial sub-sector, lack of sufficient foreign exchange to procure new machineries and the emergence of a maintenance culture have triggered a phenomenal increase in the number of spin-off industries which depend on metal recycling activities. This, it is argued, widens the horizon for scrap processing/recycling.

Jan 1, 1992

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By X. K. Lan

The greater demand for high-quality large-diameter crystals has led to the robust idea of a free- flying solar-powered furnace satellite, whereby the buoyancy-driven convection effects are almost nonexistent, and diffusion-controlled crystal growth with minimal radial segregation is promoted. In the proposed solar furnace, a paraboloid of revolution imaging concentrator is used to focus the sun&apos;s radiation onto an-ampoule which holds the solid charge to be processed. The charge will start melting in the vicinity of the focal point, after which it is translated in order for the melt to resolidify as a single crystal. A ray-trace method has been developed to determine the incident concentrated solar heat flux on the ampoule surface for a perfectly-aligned configuration with an incoming columnated beam. A transient 2- dimensional conduction problem with phase change is formulated, which is solved using the commercial code FIDAP. Results highlighting the feasibility of growing GaAs, Ge and Si crystals with diameters of the order of 20 cm using the solar furnace satellite concept are presented. The transient temperature fields within various charge materials are quantified.

Jan 1, 1994

By Autumn Fjeld

The filling and solidification of an industrial scale composite casting has been simulated to investigate the re-melting of the outer shell material during casting. Production of a composite requires a two-step casting process which includes centrifugal casting of a hard outer shell material and subsequent conventional ingot casting of a tough core material into the shell-mold assembly. During casting of the core, a thin layer of the shell material re-melts and mixes with the core material producing a bonding layer of intermediate composition. The present numerical model employs the volume of fluid method and an enthalpy-porosity technique to couple the filling of the core material and re-melting of the shell material. The interface between the two materials is tracked and can be used as a guide to examine the extent of melting and, to some degree, mixing of the two fluids and species diffusion.

Jan 1, 2008

By Xiangwen Wang

Electrodeposition of lead metal from high purity brine electrolytes containing lead chloride (PbCI,) was conducted so as to assess the feasibility of electrowinning lead-metal directly from aqueous chloride electrolytes. Tests were performed at 65 and 80°C (338 and 353°K). Characteristic features of the deposits, on both lead and graphite substrates, were correlated to operating parameters associated with: electrolyte temperature, current density and total lead- concentration. Photomicrographs of these morphological features were obtained by use of Scanning Electron Microscopy (SEM).

Jan 1, 1993

By John L. Hostetler

GALFAN, the Zn-5% Al-mischmetal hot-dip galvanizing alloy is coated onto steel sheet, wire, and tube using high-speed continuous galvanizing lines. Factors critical to producing high quality GALFAN are reviewed, The relationship between minimum mischmetal content in the GALFAN alloy and furnace dewpoint will be described. The relationship between peak annealing temperature and furnace dewpoint will also be shown. Typical suategies for operating multi-purpose hot-dip galvanizing lines including GALFAN will be described. A recent development has allowed preparation of steel smp for GALFAN coating using aqueous fluxes rather than high temperature annealing. This allows production of GALFAN-coated smp without over-ageing of the steel, and allows high steel strengths and hardnesses to be obtained. The principles of this process will be described.

Jan 1, 1992

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By V. Ramachandran

Over the past 20 years, water treatment plants have been built at various Asarco facilities to effectively handle the process waste streams that need to be bled from the system. The current paper review the several operations with reference to (a) waste streams processed, (b) process chemistry, (c) discharge options and recovery of treated water, and (d) sludge disposal.

Jan 1, 1994

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By S. J. Hogan, T. William

"By the year 2000, the steel industry, not only in the United States but in the rest of the world, will undergo significant changes. On the other hand, there will be a number of areas in which change will be minimal.The current capacity of the industry worldwide is approximately 800-810 million metric tons. This may grow to some extent, as Third World countries install capacity. However, much of it will be neutralized as the industrialized countries shrink their current capacities.There will be several breakthroughs in terms of technology, some of which deal with the production of iron outside of the blast furnace. However, these processes will not be far enough advanced by that time to replace the blast furnace, rather they will supplement it.In terms of steelmaking and the subsequent rolling process, there should be a number of basic improvements. The strip mills will roll sheets with a very slight variance in gauge, which will give the customers a better product for automatic stamping machines. Ordinary carbon steel, in a number of instances, will be replaced by high-strength, low-alloy steel, which will reduce the tonnage necessary for present-day applications, such as construction.The corporate organization will be significantly changed as joint ventures and mergers will reduce the number of companies, as well as facilities in operation. This will enable the industry to reduce its capital investment and improve operating costs, so that it will be able more effectively to compete with other materials, such as plastics, cement, aluminum, etc."

Jan 1, 1988

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By Edward Rosenberg

The synthesis and characterization of silica polyamine composites modified with a variety of sulfur containing ligands is described. The two most successful ligands in terms of sulfur in-corporation and mercury capture are ethylene sulfide and carbon disulfide. The ethylene sulfide forms either an amino mercaptane or a polysulfide upon reaction with amino groups on the composite. The carbon disulfide undoubtedly forms a dithiocarbamate functional group upon reaction of the amino group under basic conditions. Both materials posses excellent capture kinetics and capacities for mercury, Once captured, the mercury is extremely difficult to remove from the composite materials, even with concentrated acids, and they easily pass the TCLP test. The materials are compared with related thioether modified silica polyamine composites and appropriate potential applications are discussed.

Jan 1, 2003

By C. A. Nogueira, F. Margarido

"A research work has being carried out annmg at evaluating the possibility of treating simultaneously several electrochemical systems of spent batteries using the same process, in order to overcome the high costs and difficulties of selective collection and sorting. Zn-Mn02 systems, representing more than 75% of portable battery market, shall be treated in dedicated processes. The treatment assessment using a single hydrometallurgical process of the other major systems (NiCd, NiMH and Li-ion), having Ni and Co as main metals, was the aim of the research work here reported. Sulfuric acid leaching was demonstrated to be adequate for dissolving more than 90% of the metals of interest contained in batteries. The subsequent separation of metals by solvent extraction, using organophosphorous extractants like DEHPA and Cyanex 272, allowed the production of pure solutions of rare earths, cadmium/manganese, cobalt, nickel and lithium, enabling their further recovering.IntroductionRecycling is the best approach for end-of-life management of spent batteries mainly by environmental reasons but also motivated by resources conservation and, in some cases, by economic profits. Most relevant electrochemical systems of portable cells are Zn-Mn02 (ZMB, alkaline and saline), nickel-cadmium (NiCd), nickel-metal hydride (NiMH) and lithium-ion (LIB). These batteries are collected, sorted and usually treated separately, applying for pyrometallurgical or hydrometallurgical technologies, the former being the most common.Several processes have been developed and some of them industrially applied, as described in some available review papers [l, 2]. In Europe for ZMB systems the oldest processes are Batrec [3] and Citron [4]. Although having differences in details, both are based on pyrometallurgical recovery of zinc by distillation, in metallic or oxide forms, being manganese retained in the slag together with iron. Hydrometallurgical alternatives are also available, like Zincex [5] and Recupyl [ 6] processes, both using sulfuric acid solutions as leachant. The application of the existing technologies to battery recycling, instead of using dedicated processes, is other alternative already tested, being the Waeltz furnace or the Imperial Smelting some examples."

Jan 1, 2012

By Bradford H. Miller

Separation and Recovery Systems, Inc. (SRS) provides on-site waste minimization and resource recovery using its state-of-the-art MX-1500 centrifuge and MX-2000 thermal desorber. The MX-1500 can process over 450 feed tons of material per day, resulting in centrifuged cake containing 20% to 60% by weight. The MX-2000 is a hollow-flite thermal processor indirectly heated by either steam or hot oil. SRS has dewatered and/or deoiled over 1,000,000 feed tons of material in the refining, chemical, and energy industries using the MX-1500. SRS estimates that over 300,000 barrels of reusable oil have been recovered from that material. Additionally, SRS has dried and/or detoxified over 150,000 wet tons of solids or soil to regulatory or customer-specified limits using the MX-2000.

Jan 1, 1994