Search Documents

By S. -H. Jeon, Y. -S. Choi

"The three dimensional current distribution on the rectangular cathode is predicted using a boundary element method with a linear element of trigonal type. The effect of cell geometry and anode shape on current distribution is simulated. Calculated results compare well with experimental results. The proper combination of anode size and distance between electrodes increase the current uniformity.The importance of electrodeposition as a fabrication technology in the electronics industry is large and growing. The main advantages of this wet processing method, in comparison to other dry processing methods, lie in its high yield, rapid processing and low cost. In nearly every application of electrodeposition the pursuit of deposit uniformity, especially thickness uniformity, has been technically imperative. The thickness uniformity of the deposit depends largely on the current distribution over the cathode. The current distribution is primarily determined by the geometrical characteristics of the electrodes and the cell. Also the polarization at the electrode surface and the mass transfer affect the current distribution.The current distribution is an important consideration for those involved in designing electrochemical systems and electroplating systems in particular. Although it is important, the common practice in industry is to use trial and error method to design the cell that optimize the uniformity of current distributions in electroplating. The purpose of this paper is to illustrate the useof boundary element method to predict three-dimensional current distribution in rectangular cell.The calculation of the current distribution is possible by various numerical techniques, which include the finite difference method (FDM)1, the finite element method (FEM)2, and the boundary element method (BEM)3,4. These methods of the numerical calculation have various problems, respectively, but the BEM is considered to be the most efficient. This is due to the fact that the BEM has the advantage of solving field equations only on the surface of a calculation domain. A good comparison between the BEM and the FEM for the secondary current distribution in a Hull cell was made by Matlosz et al.5The fundamentals on the theory of current distribution in electroplating are well-established in the literature by a number of authors.6, 7, 8 However, a small fraction of these works have been specially addressed to three-dimensional analysis, and, mostly thel·10 have focused on the problem qualitatively rather than quantitatively.Extending the previous work to three-dimension, we developed the program for the quantitative calculation of 3-dimensional current distribution using a boundary element method with a linear element of trigonal type. Integrals with singularity from the fundamental solution have been analytically computed and it is shown in detail in the Iiterature11. This paper deals with the three dimensional current distribution for the electrode position of copper in a cubic type cell and the effect of anode shape, size and the distance between electrodes on current distribution is studied."

Jan 1, 1997

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By Rejane Tubino Geyer

The volume of electric arc furnace (EAF) plus oxygen (BOF) slag produced yearly in the world is about 84 million ton. Because of this, the study of recycling processes as a way to solve the storage problem of these slags rise in importance. There are, however, some inconvenients on using this byproduct: lime, which takes part of the process of steel production, remains as a non-reactive raw product in the slag. Since lime reacts in presence of humidity, forming expansive compounds, slag use is strongly limited. There are some utilizations for the electric arc furnace and oxygen slag in the Civil Construction Industry, mainly as base, subbase and asphalt covering in highways. However, independently of the type of recycling, a period of "cure" of about six months is necessary. Because of this slow cure process this byproduct may turn non-competitive in some regions if compared, for example, with the natural aggregate. The objective of this work is to present the flowsheet of the slags production as a residue both at the electric and oxygen steel plants and, through a bibliographic review, to analize the possibilities and limiting factors for the use of steelmaking slags in the Civil Construction Industry.

Jan 1, 1996

By G. L. Fredrickson, T. A. Johnson, B. R. Westphal, J. C. Wass, S. X. Li, D. Vaden

"Recovery of uranium from the Mk-IV and Mk-V electrorefiner vessels containing a LiCl/KCl eutectic salt has been on-going during the pyrometallurgical processing of used nuclear fuel for 14 and 12 years, respectively. Although austenitic stainless steels are typically utilized for LiCl/KCl salt systems, the presence of cadmium in the Mk-IV electrorefiner dictates an alternate material. A 2.25Cr-1Mo alloy (ASME SA-387) was chosen due to the absence of nickel in the alloy which has a considerable solubility in cadmium. Using the transition metal impurities (iron, chromium, nickel, molybdenum, and manganese) in the electrorefined uranium products, an algorithm was developed to derive values for the contribution of the transition metals from the various input sources. Weight loss and corrosion rate data for the Mk-V electrorefiner vessel were then generated based on the transition metal impurities in the uranium products. To date, the corrosion rate of the 2.25Cr-1Mo alloy in LiCl/KCl eutectic is ""outstanding"" assuming uniform (i.e. non-localized) conditions.IntroductionLow-enriched uranium products are being recovered from the Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) used nuclear fuels by a pyrometallurgical treatment process at the Idaho National Laboratory (INL). The treatment process comprises a set of operations designed to neutralize bond sodium, recover uranium from radioactive fission products, and place the fission products into acceptable waste forms [1-2]. Reactive sodium metal, essential for heat transfer purposes during reactor operations, is readily converted to chloride during the process. Electrorefined uranium products are currently being stored pending a final disposition decision. Treatment of the EBR-II used driver fuel was initiated in June 1996 while blanket fuel processing started in September 1998. These treatment processes continue on the balance of the used fuels."

Jan 1, 2011

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By Dieter Neuschiitz, Pengfu Tan

"In order to understand the sintering phenomena during iron ore sintering process, a CFD model of iron ore sintering has been developed, combining with the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. This CFD model can be used to simulate the concentrations of the gaseous and solid species, temperatures of the gas and solid, melting and molten fractions of the mixture, gas velocities, temperature zones and residence times of the gas in each temperature zone. IntroductionThe off-gas analyses clearly revealed that the off-gas of a sinter strand does not have a composition corresponding to thermodynamic equilibrium, for example, the CO, CO2 and O2 concentrations are not the mutually consistent equilibrium values. Apparently the chemical reactions in the sinter bed are controlled kinetically. Therefore kinetic modeling of sintering reactions combined with CFD modeling is necessary to understand the sintering phenomena during iron ore sintering process.Several models of iron ore sintering have been developed since 1970 [l-l 4l, each being more refined than its predecessor. The models were formulated as a series of differential equations to describe chemical and physical changes occurring at a point in the bed. These equations were solved numerically in a vertical plane along the strand. The present CFD model, based on the Nath's model [14], has been published in the reference [15]. In this work, some new chemical kinetic models of gas-solid reactions are incorporated in the present CFD model. The concentrations of gaseous and solid species, temperatures of gas and solid, melting and molten fractions of solid, velocity of gas, and residence time of gas in each combustion zone can be calculated by this model."

Jan 1, 2004

By D. P. Cook, M. I. Bloch, J. A. Dantzig

"In this article, we describe a combined experimental and computational program to study the filling of automotive wheels during low pressure die casting. Experiments are performed by placing thermocouples into the mold walls of a production caster for the Ford F 113 wheel to measure the temperature profiles in the die during processing, and to infer the filling pattern. Computational models are also developed using a 36° section of the wheel pattern, taken directly from CAD data files. We use these models to simulate the filling and heat transfer processes. Comparison between experimental and computational results are presented, demonstrating the viability of this procedure.IntroductionAutomotive companies are using increasing amounts of aluminum in production vehicles: While the main driving force is improved fuel economy through weight reduction, replacing steel wheels by aluminum also offers the potential for improved vehicle performance by reducing unsprung mass. For these reasons, many new vehicles are now supplied with cast aluminum alloy wheels, and the aftermarket for these wheels continues to grow.The most common production process for these wheels is low pressure die casting. The process is subject to numerous defects, including microporosity, cold shuts, cold folds, misruns and inclusions. Scrap rates at the caster of the order of 10% are not uncommon. Many wheels also have large production runs, into the hundreds of thousands of wheels per year. Thus, the cost savings from even small reductions in scrap rate have the potential to be quite significant.Most of the defects are associated with the filling and solidification processes in the mold. The molds are air cooled, and the placement and sizing of cooling passages is currently as much art as science. The ultimate goal of this project is to improve that situation, by implementing simulation procedures that enable engineering design methods to be used in die and process specification."

Jan 1, 2000

By Cheryl S. Lim

New technologies such as direct reduction and smelting reduction processes are increasingly being used in iron-making and steel-making in addition to conventional blast furnace technology. Critical parameters for control of these processes include the degree of metallization, degree of pre-reduction, and carbon and silica levels. On-line monitoring of these parameters is difficult because measurements often need to be made on hot ores (at or higher than -1000'C) in circumstances where representative sample streams are not readily accessible. A nuclear analyser has been developed which provides continuous, non¬intrusive, real-time measurements of iron, oxygen, carbon and silicon levels in hot ores undergoing reduction. The analyser has been tested in a plant using a direct smelting process on pre-reduced feed to the smelting vessel-, accuracies of 1% relative, 0.5 w'.96 (25% relative) and 1.0 wt.% (9% relative) were obtained for the degree of pre-reduction, carbon and silica respectively. The underlying method, capabilities and potential applications of the analyser will be discussed.

Jan 1, 2001

By Varadarajan Seshadri

A physical model based on similarity principles was constructed for simulating the RH degasser of CST (Companhia Siderurgica Tubarao, Vitoria, ES, Brazil) to evaluate the circulation rate of the metal which essentially defines the degree of exposure of the metal to vacuum in the chamber and thus of the refining rate. The circulation rate on the other hand will influence the decarburization rate and removal of dissolved gases like nitrogen and hence it is essential to optimise this parameter to get maximum refining efficiency with minimum refming times, thus improving the productivity of the secondary refining process. Mixing characteristics in the ladle is evaluated by pulse tracer addition using conductivity-meters located at the down leg as well as at several locations in the ladle. The influence of gas injection through nozzles in the upleg with simultaneous bottom injection of gas as well as nozzle blockage on the circulation rates were investigated. Also simulation experiments of kinetics of decarburization were carried out using C02 adsorption-desorption process in sodium hydroxide solution as circulating fluid and the effect of, bottom gas flow rate in this case was also evaluated. The results were carried over to prototype and to optimize the process.

Jan 1, 2003

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

The kinetics of hematite concentrate reduction by mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This process produces iron directly from iron oxides concentrates by the gas-solid flash reaction based on the partial oxidation of natural gas, resulting in a significant reduction in energy consumption and greenhouse gas emission. The reduction kinetics of hematite concentrate of an average particle size 21.3 μm by the above mentioned gases in the temperature range 1423 to 1623 K (1150 to 1350 ºC) was investigated. Hematite concentrate particles can be reduced to > 90% by any of these reductants in several seconds of residence time typically available in a flash reactor. The activation energy ranged from 214 kJ/mol for hydrogen to 231 kJ/mol for CO.

Jan 1, 2016

By S. P. Mathew

The ISASMELT Lead Process is a continuous two stage process for the production of crude lead from concentrate. It is based on the use of a top entry submerged Sirosmelt lance to produce turbulent baths in which high intensity smelting or reduction reactions can occur. The process involves oxidizing the concentrates in the first stage to produce a high lead slag. This slag is tapped continuously and transferred down a launder to a second furnace where it is reduced with coal. Crude lead and discard slag are tapped continuously from this furnace through a single taphole and separated in a conventional forehearth. Process and engineering design work for a commercial scale Lead ISASKELT plant designed to produce 60000 tpa crude lead has been completed. This plant is planned to be operational in 1991.

Jan 1, 1990

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By A. V. Tarasov, V. M. Paretsky

"A mathematical model of the low-temperature (soft) nickel oxide reduction (SNOR) in a tubular kiln has been developed including an equation describing changes in the nickel oxide content of the solid material along the length of the kiln; an equation describing the changes in the content of reagents ensuring nickel reduction (i.e., hydrogen and carbon monoxide) in the gas phase along the kiln length; as well as the temperature along the kiln length. The kinetic relationships used for the development of the model had been determined based on experiments conducted specially for this purpose. Model investigations were conducted to determine the distribution of such parameters along the length of the kiln as the contents of metals oxides in the solids, partial pressure of hydrogen and carbon monoxide, variations of the temperature depending on the SNOR process conditions, including the kiln rotation speed. Based on the data obtained, a simplified regression model of the reducing roasting process was developed.IntroductionAt the SeveroNickel complex (Russia) a technology has been developed and is being introduced on a commercial scale for low-temperature (soft) nickel oxide reduction (SNOR) in tubular kilns.The SNOR process has a number of advantages, the main of which are the higher degree of metallization and higher chemical activity of reduced nickel oxide attributable to the lower fusion of the surface of the grains of reduced material due to lower process temperature (800-1000°C) and improved reducing ability of the gaseous phase. However, the fact that the process is conducted in a gaseous phase sets higher requirements to the consistency of its composition necessitating careful continuous monitoring and control of the main process parameters."

Jan 1, 2001

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By Elli Miettinen

In Copper Flash Smelting operation disturbances may lead into dust build-up in the gas train and off-gas handling system causing reduced heat recovery efficiency and process availability. Flue dust of a Copper Flash Smelting process heat recovery boiler has been characterized and its thermal conductivity and diffusivity have been determined. Dust accretions consist of several layers possessing varying particle sizes, densities, and thermal properties, with the binding phase usually being sulphate. All the dusts can be regarded as effective thermal insulators with thermal conductivity values of less than 2 W/mK and thermal diffusivity values of less than 0.005 cm2/s. Porosity can be regarded as a fairly good indicator of the thermal transport efficiency of these types of materials, but the material microstructure must also be considered. The results can be used in the dimensioning of metallurgical heat recovery boilers and they also provide accurate input data for process models.

Jan 1, 2009

By John Demol

Monazite, a rare earth and thorium phosphate mineral, is one of the major minerals processed for extraction of rare earths. Industry practice for treating monazite concentrates is to use either a sulfuric acid bake or caustic conversion route. In the sulfuric acid bake, monazite concentrate is mixed with concentrated sulfuric acid and roasted. The rare earth phosphate mineral is converted to rare earth sulfate which dissolves in a subsequent water leach. As the bake temperature increases above 300 °C, thorium becomes less soluble. Although acid baking is practised in industry, the bake reactions are not well understood. A combination of chemical analysis, XRD and SEM-EDS was used to identify reaction processes occurring during sulfuric acid baking of a 93 wt% monazite concentrate between 200 °C and 800 °C. The effects of these reactions on the leachability of the rare earths, thorium and phosphate were also examined.

By Andre Thess, Oleg Zikanov

"Direct numerical simulation methods are applied to study the influence of a constant magnetic field on turbulent flows of liquid metals. The flow is assumed to be homogeneous and the problem is reduced to the classical case of the turbulent flow in a 3D box with periodic boundary conditions. The main subject of the study is the anisotropy developing in a liquid metal flow affected by constant magnetic field.To investigate the long-time evolution of initially isotropic flow the large-scale forcing is applied to maintain the flow energy at a statistically steady level. It is found that the flow evolution depend strongly on the magnetic interaction parameter (Stuart number). In the case of small Stuart number, the flow remains three-dimensional, turbulent, an approximately isotropic. At large Stuart number (strong magnetic field) the turbulence is suppressed rapidly and the flow becomes two-dimensional and laminar. Very interesting is the intermittent flow evolution at moderate Stuart number. Long periods of almost two-dimensional, laminar behavior are interrupted by strong turbulent three-dimensional bursts.The influence of a constant magnetic field on scalar transport properties of liquid metal turbulence is investigated using the simplified formulation of homogeneous flow driven by an imposed mean temperature gradient. Such a flow consists primarily of two turbulent antiparallel jets providing an effective mechanism for heat transfer. It is shown that the magnetic field parallel to the mean temperature gradient stabilizes the jets and, thus, enhances heat transfer considerably."

Jan 1, 1999

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014