Search Documents

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By James D. Navratil

The mineral magnetite, or synthetically prepared iron ferrite (FeO?Fe2O3), has been used to separate a wide variety of substances, such as dissolved metal species and particulate matter, from wastewater. In the absence of an external magnetic field, activated magnetite readily adsorbs numerous metal species including actinide elements. In the presence of the external magnetic field, enhanced capacity was observed in using supported magnetite for removal of actinides and heavy metals from wastewater. The enhanced capacity is primarily due to magnetic filtration of colloidal and submicron particles along with some complex and ion exchange sorption mechanisms. The removal of the magnetic field and use of a regenerating solution can easily regenerate the loaded magnetite. The process has recently been tested for the removal of other metal ions including cobalt and iron. This paper will review previous work on the use of iron oxides for wastewater treatment and discuss the development and potential of the magnetic filtration/sorption process for wastewater treatment applications in hydrometallurgy.

Jan 1, 2003

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Milton Manrique, Edgar E. Vidal, Patrick R. Taylor

"Ultrafine zirconium carbide powder has been synthesized using zircon concentrate and methane in a thermal plasma reactor. The effect of several experimental variables, such as power used and zircon particle size, on the conversion has been studied. A thermodynamic analysis of the possible reactions and stable compounds was performed. A mathematical model that describes the in-flight decomposition of zircon particles was developed based on a description of the temperature and velocity profiles calculated in the reactor. It was shown that the formation of zirconium carbide from zircon and methane is thermodynamically possible. Complete 'vaporization of zircon in the reactor is predicted when the particle size is below 45flm and the effective power entering the reactor is 15 kW. The powders were collected and characterized by XRD, SEM, TEM and chemical analysis using ICP. Results of the product analysis indicated the presence of zirconium carbide, zirconium oxide, silicon carbide and silicon oxide.IntroductionIn recent years there has been an increased interest in the production of nanometric sized powders of ceramic materials for use in advanced materials applications. One possible method to produce these powders is with a thermal plasma reactor, which offers high temperatures and fast quenching rates. This technology has been called - Thermal Plasma Synthesis - [1].Zirconium Carbide (ZrCx) has typical properties of transition metal carbides: elevated hardness - between alumina and diamond - a high melting temperature of 3420°C and high chemical stability at room temperature [2]. ZrCx has a Bl crystal structure with deficiencies in the number of carbon atoms in the cell with x between 0.6 and 1 [3]. Different methods have been used to produce ZrC, one method is by direct reaction of zirconium hydride or halide with carbon. Other methods used are direct reduction and carburization of zirconium oxide (Zr02) and reaction of metallic zirconium with a caburizing gas such as acetylene [3]. Recently small films of ZrC have been obtained using a sputtering device [4,5]. ZrC has been used in nuclear plants as a low neutron absorbing and high mechanical resistant refractory material and also as a constituent in cathodes made of UC-ZrC [6]. It is also used in the form of tubes, boats and crucibles to handle molten metals and as part of electronic devices used for thermoionic transducers. Recently ZrC has been used along with zirconium diboride (ZrB2) to produce composite materials [7,8]."

Jan 1, 1996

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By Yuzuru Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about 1880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Zhihe Dou

SHS reaction system has advantages of heat flux density, energy concentration and reaction speed, with sufficient conditions in thermodynamic and kinetic reaction. This paper invented a new technology of SHS metallurgy of preparing melting point alloys and refractory compounds using its own chemical energy. SHS-leaching process for preparing nano boron powder or ultrafine boride powder and SHS-casting process for preparing titanium-based alloy and immiscible alloy were studied. The results indicate that highly active boron powder of greater than purity of 93%, particle size less than 100nm and purity greater than 98.5%, particle size less than 400nm REB6 can be prepared. With SHS-Casting process, the oxygen content of less than 0.59% ferrotitanium, oxygen content of less than 0.5% titanium alloy and ?40-80*100mm large size of CuCr, Cu-Fe alloy ingots were prepared. This technology has greatly enhanced the thermal reduction method added values of preparing metallurgical products and its competitiveness.

Jan 1, 2014

By Reinhard Bott

The Companhia Mineira de Metais (Brazil) runs a Zn-recovery plant in Tres Marias, federal state Minas Gerais, Brazil. The Zn-production is about 65,000 t/a, This corresponds to a concentrate throughput of about 255,000 t/a with a Zncontent of about 29.5 % at an output of 85 %, The plant is run continuously 360 d/a and 24 h/d, respectively. From this it can be concluded that: Input: approx. 650 - 700 t/d ore-concentrate and approx. 29 t/h ore-concentrate, respectively.

Jan 1, 1990

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By Olli Hyvärinen

The capacity of Outokumpu Pori Copper Refinery has been increased by 50 % to 70 000 t/a in the last five years by adopting periodic current reversal, reducing spacing and installing some new cells in the old tank house building. Five years operation of PCR has proved that it is possible to achieve additional capacity with PCR and yet produce high quality cathodes. The impurity level in anodes has considerably increased, and recently, arsenic, antimony and sometimes bismuth have displaced nickel as the most critical impurity.

Jan 1, 1987

By Y. H. Wang, S. Kou

"Three-dimensional weld pool convection was computer simulated using dimensionless variables. The electromagnetic force, the buoyancy force and the surface tension gradient on the pool surface were treated through the use of the dimensionless electromagnetic force, the Grashof number and the Marangoni number. Other typical dimensionless numbers such as the Prandtl number and the Peclet number were also used. The calculated and experimentally observed fusion boundaries were compared. The convection patterns were shown and the effect of the Marangoni number was demonstrated. IntroductionSeveral weld pool convection models have been developed by Oreper et al. (1,2), Chan et al. (3) and Kou et al. (4). These models describe two dimensional convection in stationary weld pools in a semi-infinite workpiece. Since the vast majority of arc welding practices involve a moving heat source and weld pool, and the workpieces are finite in thickness rather than semi -infinite, a 3-D convection model for a moving heat source and a workpiece of finite thickness is expected to be much more useful.Weld pool convection can strongly affect the structure and properties of the resultant welds. Variations in weld characteristics which are likely to occur from changes in weld pool convection are: weld penetration, macrosegregation, gas porosity, solidification structure, undercutting and surface smoothness. Apparently, the quantitative understanding of convection and heat flow in weld pools is of considerable practical interest. Mathematical models describing convection and heat flow in weld pools are essential, not only because of the quantitative understanding they provide, but also because of the difficulties associated with the experimental measurements of weld pool convection. These difficulties are mainly due to the fact that only surface flow, rather than the overall convection pattern in the weld pool, can be observed. In fact, due to arc glow even the observation of surface flow can be rather inconvenient."

Jan 1, 1986

By Robert W. Bartlett

Chalcopyrite in copper flotation concentrates can be hydrothermally converted to digenite with oxygen in a continuous process, with rapid kinetics when operated above 200°C. This eliminates large amounts of sulfur and iron. These "super-concentrates" have potential for debottlenecking smelters and avoiding capital intensive future smelter expansions, otherwise required in the late 1990s. The technology of producing super- concentrates is described, with cost estimates, and the use of super-concentrates as smelter feed is discussed, with examples.

Jan 1, 1992

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By Messias dos Santos Machado, Renato B. Godoy, Roberta Lima, Andressa Silva, Francisco Valenzuela-Díaz, Rene R. Oliveira, Esperidiana Moura

This work aims to incorporate the Bof White Clay, from Boa Vista, Paraiba State, Brazil, as natural nanofiller in Ehylene vinyl alcohol copolymer (EVOH) and obtain flexible films. Nanocomposite was obtained using a twin-screw extruder, and film formed using a blow extruder machine. The flexible film nanocomposite was characterized, by tensile tests, XRD, DSC and their properties were evaluated. The results showed a good interaction between the clay and the EVOH resulting in an increase of properties of films nanocomposites as compared to films neat polymer.

Jan 1, 2015

By Teruo Bitoh, Shogo Izumi

"The effect of B203 flux melting on the structure and the soft magnetic properties of the (Feo.1sBo.20Sio.os)96Nb4 bulk metallic glasses prepared by casting has been investigated. The ringshaped bulk specimens were prepared by the B203 flux melting and copper mold casting. It was confirmed that the flux melting promotes the precipitation of the a-Fe(-Si) and Fe2B phases in the central region of the specimens. The ring-shaped bulk specimens show a flat hysteresis curve, indicating a good linear relationship between the magnetic induction and the applied magnetic field. These results show that it is possible to develop a new soft magnetic material that exhibits constant permeability, which is necessary for producing inductors and choke coils.IntroductionSince the success of forming Fe-based bulk metallic glasses (BMGs) with good soft magnetic properties, great attention has been developed to synthesis and properties of the BMGs [l, 2]. The BMGs have high glass-forming ability (GFA) and, therefore, they can be used to prepare bulk amorphous alloys with a thickness of the order of a few millimeters by casting. The soft magnetic properties of Fe-based BMGs are better than those of ordinary amorphous alloys; therefore, these BMGs have wider applications as soft magnetic materials [3-5]. It is often required for soft magnetic materials that the shape of the hysteresis curve is changed according to the demands of applications. For example, materials with ""flat hysteresis curves,"" which means the magnetic flux density (B) and the applied magnetic field (H) show a linear relationship up to rather high magnetic field, are necessary for producing inductors and choke coils. Flat hysteresis curves can be easily achieved by creating an air gap in the magnetic path. However, magnetic flux leakage generated in the air gap inhibits high-density packing of the electronic components. In order to achieve flat hysteresis curves without creating an air gap, Fe-based ordinary amorphous alloys are subjected to crystallization by annealing and transformed into thin surface layers of a-Fe; the crystallization results in the compression of the remained amorphous phase [6]. Another way to achieve flat hysteresis curves is the formation of secondary phase (such as Fe2B) that act as pinning site of magnetic domain wall displacements [7]."

Jan 1, 2013

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009