Search Documents

By F. M. Nakla

Various methods of Applied Mineralogy were used for determining the nature and composition of products yielded by flotation tests for Maghara coal beneficiation. Coal samples obtained from the Sa fa mine in Northern Sinai, Egypt, were crushed, sieved, &apos;and <32 mesh size fraction was cleaned by froth flotation. Experiments were conducted to determine the effect of certain parameters on beneficiation of Maghara coal by flotation. The investigated factors included nature of frothing and/or collecting reagents, pH value of the medium, particle size distribution in the head sample, and pulp density of the coal slurry. The quality of head samples, coal concentrates, and tailing products were determined by chemical analysis, microscopic study, x-ray diffraction analysis, and occasionally by infrared (IR) absorption spectroscopy.

Jan 1, 1989

By Juan Daniel Martínez, Janaina Accordi Junkes, Dachamir Hotza, Tatiana Pineda

"The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. The results showed the technical viability of producing both heat and amorphous silica from a renewable energy source. This paper presents the characterization of rice husk ash (RHA) obtained under varying fluidization velocities (0.13-0.15 m/s) and rice husk feed (4.5-7.2 kg/h). Characterization techniques include X-ray fluorescence, X-ray diffraction, particle size distribution and scanning electron microscopy. For the employed range of fluidization velocities of rice husk feed no noticeable influence on the chemical composition of produced RHA was observed. After combustion, RHA containing ~93% amorphous silica and <3% unburned char was obtained. RHA primary particles presented sizes from 90 to 100 µm and a tendency for agglomeration in aqueous media. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.IntroductionDue to the increase of the agroindustrial production, the concern with processing by-products, such as rice husk (RH), is growing. For a better material and energy use, allowing a cleaner production and a more maintainable development, RH can be used as renewable fuel in the production plant, for instance, in steam generators. The adequate combustion of RH generates hot gases with low levels of pollutants, as carbon monoxide and particulate material.RH is the protecting coating formed during the growth of the rice grain, composed by four structural layers.1 The main components of the husk are cellulose and hemicelulose (50%) besides lignine (26%) and organic components (4%), as oils and proteins. The remaining amount includes inorganic materials (SiO2, Al2O3, K2O, Na2O, MgO, CaO, Fe2O3, MnO, P2O5).1The rice husk ash (RHA) is the product of the termochemical transformation of RH. The conditions of the different conversion processes (pyrolysis, gasification and/or combustion) determine the physical-chemical characteristics of the final product. RHA corresponds to 14 to 25% RH, depending on the variety of the rice, climate and soil of the producing area.2-4 The main component of RHA, which is generated at moderate combustion temperatures, is amorphous silica (SiO2) in the range from 80 to 97%.4,5"

Jan 1, 2008

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By M. W. Wadsley

Despite the convenient subdivision of extractive metallurgy into hydro- and pyro- divisions, many flowsheets contain both types of process. When complex materials are used as feed, combinations of hydro- and pyro-metallurgical processes are even more common. Hydrometallurgy is used to treat many by-products and waste-products. (Bio-metallurgical processes may be considered to be a sub-set of hydro-metallurgical processes.) Combinations of the different processes in the Australian metallurgical industry are described. Selected international examples demonstrate that the use of combked processes is not a unique. Antipodean phenomenon. The motives for selection of combined pyre- and hydro-metallurgical processes in a flowsheet are examined.

Jan 1, 1994

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By S. Djaroudib

Keywords: iron recovery, hematite, hydrolysis, polyvinylpyridine The precipitation of hematite (Fe2O3) from ferric chloride media at ambient pressure and at temperatures below 100°C was studied as part of a program to recover a marketable iron product form metallurgical processing streams and effluents. Hematite was formed in preference to ferric oxyhydroxides (e.g. ß-FeO?OH) by controlling the precipitation conditions, especially by adding Fe2O3 seeds. The extent of the hydrolysis reaction was found to depend primarily on temperature and on the free-acid concentration. As to the latter, the controlled addition of an adsorbent of free acid, in our case the anionic resin polyvinylpyridine (PVP), was shown to allow for the nearly complete removal of iron as readily filterable Fe2O3. The hematite product typically contains = 63% Fe and = 1.5% Cl, and its composition does not change appreciably upon repeated cycling using regenerated PVP.

Jan 1, 2005

By Rod Samuels, Rupert Allen, Thomas Harper

"Viceroy Resource Corporation of Vancouver, B.C., has recently developed and brought into production the Brewery Creek Mine, an open-pit heap leach gold mine, located 55km east of Dawson City in Yukon, Canada. Mineable reserves are 15.2 million tonnes of ore grading 1.45 grams/tonne, containing 22 tonnes (707,315 oz) of gold. Ore processing employs the heap leach technology using run-of-mine ore. Highlights of 1996 activity included construction of a 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1. 46 gpt to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting of this mine has drawn significant attention because of the innovated heap leach technology; although this technology has been proven in other jurisdictions, it has not been used at such extreme northern sites where winter temperatures routinely reach -45°C for extended periods.ABSTRACT ONLY"

Jan 1, 1997

By F. Field, R. Kirchain, J. Gregory

Utilizing alternative materials is an important tactic to improve the environmental performanceof products. Currently a growing array of materials candidates confronts today’s product designer. While life-cycle assessment (LCA) methods provide quantitative input into this selection decision, their implementations are evolving and disparate. The goal of this paper is to explore several major analytical variations of LCA implementations and the implications of these variants across a range of application contexts. Specifically, this paper examines analytical variations in valuation method and treatment of recycling by exploring allocation methods that affect product end-of-life. Case studies across a range of materials are presented, including materials that exhibit a spectrum in variation of environmental performance and material degradation between primary and secondary applications. Preliminary results indicate that the choice of analytical method can have real impacts on individual metrics and there are sets of analytical variation over which strategic results are strongly affected.

Jan 1, 2008

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

By José C. Escobedo B.

A kinetic study of nitrogen dissolution in a. electromagnetically stirred Co-Cr-Mo alloy bath was made. The experiments were carried out at 1693, 1723 and 1743K of temperature, with a nitrogen pressure of 0.67 atm. The mass transfer coefficients were obtained, finding that their values increase as temperature grows. The true kinetic constants were calculated. It was found that at 1693K of temperature, the kinetics of the nitrogen dissolution process is controlled by a mixed mechanism involving both transport processes and chemical reaction, while at 1723 and 1743K of temperature, the kinetics is controlled only by transport processes mechanisms.

Jan 1, 1995

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By M. M. Swan

A stratiform gold occurrence of Precambrian age located 20 miles southeast of Prescott, Arizona, within the Agua Fria Mining District, displays chemical, mineralogical, structural and lithological patterns indicative of a distal, exhalative volcanogenic environment. Metavolcanic and metasedimentary rocks of the Proterozoic Yavapai Series (1775-1820 m.y.) host the mineralization and are&apos;characterized by greenschist grade metamorphism, steeply-plunging penetrative folds and steeply-dipping schistosity. Mineralization is confined to a 100m thick stratigraphic section that is comprised of a series of thin auriferous massive sulfide beds and intercalated schist .containing disseminated sulfides. The mineralization extends more than 4km along strike. Coincident with, and largely confined to the mineralized strata, are anomalous amounts of As, Sb, Cu, Pb, Zn and Ag and associated silicification, sericitization and carbonatization. This exhalative mineralized system is interpreted to have been deposited in a paleo topographic low on the distal flank of a submarine rhyolite dome and to represent the final episode of a Precambrian volcanic cycle.

Jan 1, 1981

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Yoichi Takeda

Copper solubility in SiO2-CaO-FeOx slag equilibrated with copper matte in 10% SO2 atmosphere at 1573K was estimated. Essential parameters are activity coefficients of copper oxide and sulfide, oxygen and sulfur potentials and activity of copper in the slag-matte system. A large number of experiments provide proper parameters to calculate copper solubility in slag, A classical thcrmodynamic model postulating CuO0.5 and CuS0.5 moleculcs assists in estimating copper solubility in slag. Additions of Si02 and CaO reduce copper solubility almost in any condition. Copper loss, that is function copper solubility and slag volume, in the silica saturated SiO2-FeO. binary slag is minimally equilibrated with less than 66% copper matte while copper loss in the 50% FeO.-SiO2-CaO ternary slag saturated with 2CaOSiO2 is minimally equilibrated with over 66% copper matte. This slag composition has potential for continuous copper converting, direct copper production or high-grade matte production.

Jan 1, 2003

By Yuanpei LAN, Minren XU, Deliang NIU, Zhu WANG, Qingcai Liu, Shan Ren

Removal of gas is the major function of RH degasser. To optimize the RH refining craft in Chongqing Iron and Steel Co. Ltd, the degassing effect of RH degasser at different degrees of vacuum was investigated using a vacuum induction furnace. In addition, the effect of processing time on the gas content dissolved in molten steel was also studied. The results showed that degree of vacuum was one of the important factors that determined the degassing efficiency in RH refining process. High vacuum degree is helpful in the removal of gas, especially in the removal of [H] dissolved in molten steel. The processing time could be reduced from 25-30 min to 15 minutes and gas content could also meet the demand of RH refining

Jan 1, 2015

By A. C. Wadhawan

In the present context of rapid industrialization, production of Lead-Zinc metals from low grade materials, residues and wastes can make substantial contribution to the supply of these metals in India. Recovery from secondary sources also plays an important role in conservation of mineral resources and lower power consumption. Conscious effort is therefore, required to increase the secondary metals which, besides saving in energy cost will also help in waste material management and keeping environment clean. The major thrust is, therefore, needed in this direction. During all these years, the Indian Lead- Zinc industry has made sustained efforts for recovery of metals from low grade ores and from metallurgical wastes and residues. The paper identifies the treatment of low grade ores by various technologies and techniques and the treatment of metallurgical residues and wastes generated during primary Lead and Zinc smelting in India. Some of the major achievements in past decade have also been elaborated in the paper. The strategies to be followed for continuing treatment of low grade ores and waste materials by adopting newer, environmental friendly technologies, in consonance with the rigid standards being adopted by most of the countries including India. have also been dealt with in the paper.

Jan 1, 1994

By Dandan Jian, Christian Karcher

Information of liquid steel flow patterns inside the mold may be obtained from the velocity at the free surface (meniscus). This meniscus flow may be measured using the contactless electromagnetic technique termed Lorentz force velocimetry (LFV). It is based on the measurement of Lorentz forces acting on a magnet system when an electrically conducting metal melt interacts with the field lines stretched by the magnet system. Force sensor and the magnet system form a so-called Lorentz force flowmeter. In this paper we present a series of model experiments that demonstrate the feasibility of using two identical flowmeters that are arranged in a certain distance one behind the other. In this case, surface velocity may be determined by just cross-correlating the two force signals recorded by the two sensors. This technique is called time-of-flight LFV. A special prototype of a respective measuring device, called meniscus velocity sensor (MVS), has been developed to measure local free-surface velocity. In the present paper we describe experimental results of respective measurements in the model test stand LiMeSCo (liquid metal surface velocity correlation). To check the potential of the time-of-flight technique, in a first step we measure surface velocities during solid-body rotation of metallic substances. We observe that small modulations in the signals that are due to the natural unevenness of the solid body can be used to determine surface velocities. In a second step we apply the time-of-flight technique to liquid metal free-surface flow. Here we use the low-melting eutectic alloy GaInSn as a test melt. In this case we observe that the cross-correlations between the signals are much rarer and much weaker than in the solid-body experiments. We conclude that the presence of the localized magnetic fields, produced by the permanent magnets of the flowmeter, give rise to intense deformation of the free surface and the creation of surface waves. The field acts as a magnetic obstacle. We observe that the flow velocity is decreased right underneath the magnetic field and is accelerated in the side regions. This magnetic obstacle effect may restrict the determination of the local surface velocity in application.

Jan 1, 2012

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013