Search Documents

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By R. D. Lrwin, W. M. Mullins, S. Venugopa, J. C. Malas

"Physical models for acoustic emission (AE) are introduced and expressions are derived to predict AE activity from such parameters as applied stress, strain and strain-rate. These models are then incorporated into a visco-plastic finite-element simulation program, and the acoustic emission event rate generated during metal forming operations are predicted. Simulation results are presented for upsetting operations on a typical C-Mn type steel for various friction and die geometry conditions. The AE model predictions compare well with the limited available experimental results reported in the literature and demonstrate that AE signatures can be reliably simulated. The signatures predicted for metal forging are fairly insensitive to processing parameter changes. This suggests that AE event rate monitoring may not be well suited to process monitoring for forging. However, the size of the features is conjectured to influence the frequency content of the AE signals. Thus, since current simulations include only the ability to predict the number of events for a set of processing conditions, future work is required to simulate the duration and magnitude of acoustic events. Fourier analysis techniques may then be applied to investigate correlation with microstructural features.IntroductionThe open loop control system method for deformation processing design, as described by Malas et al. [1 ], consists of several steps in series to achieve the final design. The first step uses microstructure development models to determine the optimum deformation path to achieve the desired final microstructure. The second step, the process model, calculates the processing parameters required to achieve this deformation path. Finally, the metal-working system uses the required processing parameters to produce the part. Figure 1 shows this in block diagram form"

Jan 1, 1997

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Nozomu Uchida, Uematsu Keizo, Daisuke Shouji

"Grain orientated microstructure was developed for the improvement of ceramic characteristics. Novel polarized light microscopy was developed to examine the grain orientation quantitatively. The degree of grain orientation was estimated from the retardation determined with a Berek compensator. The method was essential to determine a minor grain orientation, which could not be analyzed by means of conventional X-ray measurements. The data were favorably related to ceramics characteristics. The comparis of the ceramics with various degree of orientation was very important to explain the change of ceramic characteristics with processing.IntroductionMicrostructure with grain orientation has a high potential for greatly improving characteristics of ceramic. However, there has been strong restriction on processing and material for developing this structure. It has been crucial to apply forming methods involving high shear such as injection molding1). Grains must have an elongated shape.In recent years, much attention has been paid on the effect of high magnetic field on diamagnetic materials2)3)4), Many ceramic materials are known to be diamagnetic. High magnetic field has a high potential to orient grains. The principal driving force for grain orientation is the magnetic anisotropy of material, which is generated by non-cubic crystal symmetr5). This method of grain orientation is not restricted by grain shape, and can be applied to all materials having non-cubic crystal structure.This study uses alumina as raw materials, and produces alumina ceramics with orientated grain in high magnetic field (10T). Alumina has a magnetic anisotropy due to hexagonal crystal structure. The degree of grain orientation in the green and sintered bodies will be examined and their relevance to magnetic field will be discussed."

Jan 1, 2000

By Susan A. Fredholm, Randolph E. Kirchain, Elsa A. Olivetti, Jeremy R. Gregory, Jeffrey B. Dahmus

"A general model for evaluating the economic and environmental performance of electronics recycling systems is developed. This model comprehends the three main functions in a recycling system – collection, processing, and system management – and aims to enable quantification of the impact of context and system architecture on the economic and environmental performance of electronics recycling systems. Such a model can be used both to evaluate and improve existing electronics recycling systems, as well as to design and implement new systems. A case study, based loosely on Maine, is presented to show the utility of such a model.IntroductionAs recycling systems for complex durable goods (CDGs), and in particular for waste electronics, become more widespread, understanding the economic and environmental performance of such systems becomes critical, both to enable improvement of existing systems and to inform the design of new systems. However, with the range of possible system architectures and the important role of locational characteristics (context), understanding the determinants of system performance is challenging [1]. To address this issue, a modeling framework to project the economic and environmental performance of CDG recycling systems, based on contextual and architectural characteristics, has been developed.The modeling framework presented here comprehends the three main functions – collection, processing, and system management – which are common to most recycling systems. These three functions are modeled using a variety of modeling techniques and serve as a bridge between inputs related to system context and system architecture, and outputs related to economic and environmental performance. The models developed here are intentionally meant to be both broad, in order to address entire recycling systems, and general, such that many different systems, both real and hypothetical, can be analyzed."

Jan 1, 2008

By Biao Zhou, Qian Li, Kuo-Chih Chou, Yi-Long Liang, Jie-Yu Zhang, Qun Luo

"In this work, the phase transformational behaviors and microstructural characteristics of 60Si2CrVAT spring steel were systematically investigated as a function of applied cooling rates in the range of 0.l-10°C/s. A quenching deformation dilatometer was used to austenize and quench. The dilatometric curves between length changes and temperature of samples suggest three characteristic stages could be identified as different ranges of cooling rates, which meets well with metallographic examination and the measured hardness results. As the cooling rate increases, the structure transformed from pearlite, granular bainite to finally martensite. The F + P and B zones are completely overlapping in continuous cooling transformation (CCI) curve, which indicates that this steel is difficult to become single bainite and shows good hardenability.IntroductionThe 60Si2CrVAT, a high-carbon low ally super-high strength steel developed from the ?OCT 60C2XFA and 60Si2MnA, is often used for coil spring of heavy vehicles and high-speed railway by hot deformation or cold deformation [1-3]. The addition of Si improves relaxation resistance significantly, through the refinement of tempered carbides as the result of the retardation of E -carbide conversion to cementite during tempering. Due to its deleterious effects on decarburization and toughness, the maxinJum content of Si has limited to 1.5 or 2.0% [4-5]. Additionally, V and Cr can improve sag resistance due to the precipitation of fine carbonitrides during hot rolling [6-7]. To best of our knowledge, the strengthening by precipitation of alloy carbides of Cr and V often referred to secondary hardening [8]."

Jan 1, 2013

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By Hideya Sato

Refractory wear caused by melts is one of the major determining factors for the interval of shut-down repair of the metallurgical furnaces in general. Calcium ferrite slag employed by M it subishi Continuous Copper Converter, shows hi& fluidity and corrosive characteristics against most of the refractories. In order to improve the corrosion resistance of the refractories, the mechanism of MgO-based refractory wear by the calcium ferrite slag was intensively studied. The dissolution behavior of the refractory into the molten slag and the penetration of the molten slag into the refractory were observed by crucible tests and newly developed oscillating furnace tests. It was found that the wear of MgO-based refractories by the calcium ferrite slag is mainly dominated by the internal structural failure caused by the penetration of CaO-Cu20 rich slag which is formed as a result of the preferential absorption of FeO, from original slag by the spinel of the refractory.

Jan 1, 1999

By Akio Ohta

The Hyuga smelter has been producing ferronickel by a rotary kiln-electric furnace process in Miyazaki, Japan. Several approaches to improve our operation have decreased the electrical energy consumption. A new process was developed to decrease the cost of energy even further. Oil and technical oxygen are injected through lances to heat up the calcined ores (calcine) instead of the electric power. Main problems during the development of the process were the short life of the water-cooled lances, the check on security of the safety system and the eruption of combustion gases through the calcine bed. These problems have now been overcome successfully, and stable operation can be maintained. The addition of 1 Litre of heavy oil per tonne of ore can save the electrical energy requirement by 8.6 kwh per tonne of ore. The new process has resulted in a reduction of the electrical energy consumption by more than 10 percent

Jan 1, 1992

By Young-Geun Park

A new decarburization model for the RH system was constructed for calculating the decarburization reaction using a three-dimensional fluid dynamics program. The entire fluid flow in the RH process was calculated by evaluating the shape and volume of the plume zone, formed by Ar gas blown through multiple nozzles on the wall of the snorkel. On the basis of this fluid flow, the decarburizaiton reaction was calculated through establishing the decarburization reaction model, which considers the thermodynamics, reaction kinetics, and the decarburization sites (Ar bubble surface, bath surface, and the CO bubble fomtation at inner sites). The results from this model were compared with a real RH operation results with good agreement. Because it is possible to predict the carbon concentration at various conditions using this model, it may be useful in increasing the decarburizaiton rate. Key words : RH process, plume zone, decarburization, Ar bubble surface, bath surface, inner site, circulation flow rate.

Jan 1, 2001

By Karl-Heinz Daum

Outokumpu Lurgi Metallurgie GmbH, Oberursel, Germany ? give saleable by-products, ? not interfere with smelter performance, ? treat all gas streams simultaneously, and ? comply with environmental regulations. The latest developments in sulphuric acid plant design are presented.

Jan 1, 2002

By Liguang Zhu, Yihua Han, Qingjun Zhang, Xiaoyan Wu, Pengcheng Xiao

The evolution of chemical composition, size, proportion, and morphology of the Al-Ti-Mg-O inclusions during the steelmaking process of Interstitial Free (IF) steel from the RH to the Continuous Casting (CC) slab were investigated by means of Auto-SEM. Results showed that many of Al2O3 and MgO-Al2O3 type inclusions are modified by TiOx, while most of their shapes are irregular due to the high melting temperature. The composition evolutions and melting characteristics of Al-Ti-Mg-O inclusions under different contents of [Al], [Ti] and [Mg] were estimated by using thermodynamic software Factsage 7.0. Results showed that estimated results are in good agreement with the analysis results of industrial samples. Both the Ti alloying and spontaneous enrichment would make a high Ti concentration environment that was in favor of the TiOx existence. Moreover, more TiOx component can modify MgO-Al2O3 spine inclusion into inclusions with a lower melting temperature.

Mar 1, 2018

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA&apos;s oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

By Nagy El-Kaddah

One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100µ inclusions are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate ?the capability of the system for producing super-clean metals.

Jan 1, 1996

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By S. L. I. Chan, M. Z. Quadir, D. C. Austin, P. J. Hazell, A. Chen, A. A. H. Ameri, D. East, J. P. Escobedo, M. A. Bevan, A. D. Brown

The microstructure and mechanical response of additive manufactured Ti64 under compression and tension has been investigated. Quasi-static and dynamic experiments were conducted on electron beam powder bed Arcam A1 (EBM) and blown powder laser Optomec LENS MR-7 (LMD) additive manufactured specimens. Hot isostatic pressing (HIP) was conducted on both of the additive manufactured specimens and results were compared with as-received specimens. Digital image correlation (DIC) was utilized to observe the in situ development of deformation fields during tensile loading. Optical microscopy was conducted on pristine and deformed specimens to examine the microstructure of the specimens. HIP treatment reduced the porosity by *90% with a concomitant increase in hardness by 40%. The results from tensile experiments show that additive manufactured Ti64 display a higher values for the yield stress, hardness, and ultimate tensile strength than conventionally manufactured Ti64. Under quasi-static compression, it was observed that EBM specimens exhibit a higher yield strength and ultimate tensile strength than LMD specimens.

Mar 1, 2017

By Liu bing-guo, Peng Jin-hui, Guo Sheng-hui, Kong dong-cheng, Hu jin-ming, Zhang Li-bo

The novel technology of calcination to prepare triuranium octaoxide（U3O8）from ammonium uranyl carbonate in microwave fields was investigated on the basis of the temperature rising characteristics of ammonium uranyl carbonate, triuranium octaoxide (U3O8), and their mixture. The result of experiments show that ammonium uranyl carbonate had weak capability to absorb microwave energy, while triuranium octaoxide has the very strong capability to absorb microwave energy and the sample temperature increased rapidly with an increase mixture ratio of triuranium octaoxide. The optimal calcination conditions were as follows: microwave power 700 W, calcination time 10 min and 60 g in this experiments range, respectively. Under these conditions the value of total uranium and 4 U of triuranium octaoxide was 84.28% and 31.02%, respectively. It is feasible to prepare triuranium octaoxide by calcination from ammonium uranyl carbonate, which mixed with small amounts of triuranium octaoxide under microwave fields.

Jan 1, 2015

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015