Search Documents

By Enrico Cerilli, Bryan Salt

Xstrata Nickel’s Sudbury Smelter has systematically developed its converting aisle from a single stage to a counter current multi stage converting process. This has required the development of two unique converters; the Slag Cleaning Vessel (SCV) and the Slag Make Converter (SMC). This has resulted in a unique three stage converting process that enables treatment of secondary materials and producing a slag that can be discharged without further treatment. The paper will also discuss future changes currently being considered to further improve environmental, plant hygiene and productivity performance.

Jan 1, 2009

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By I. J. Moon

The reduction behavior of hematite by H2 and H2-CO gas mixtures was investigated to elucidate the reduction mechanism at 800-950 °C. The hematite compacts were made by Cold Isostatic Pressing to produce compacts of uniform shape and size. The compacts were sintered at 1000° C for 30min, and showed a contraction of 29%. Mercury pressure porosimeter was used for measuring the total porosity, pore size distribution and pore surface area of the compacts. Reduction was measured by means of weight-loss technique using Cahn Balance (Model : TG-171, capacity log, accuracy f 10pg). Microscopic examination and X-ray analysis were used to correlate the structure of reduced compacts with the mechanisms of reduction. Neither chemical reaction control nor diffusion control is adequate in describing the complete course of reduction of the hematite compact. The reduction of hematite compacts was initially controlled by the chemical reaction at oxidelmetal interface. The reaction goes through a transition phase .where it is undergoing a mixed control, followed by the diffusion control towards the end of the reduction. The values of apparent activation energies for chemical reaction control were 3.48-8.43 kcal/mol depending on the gas compositions.

Jan 1, 1997

By Wenxuan Xu, Shusen Cheng, Guolei Zhao

According to cross beam temperature measuring data of stock surface gas flow in blast furnace production process, using zoning method to deal with stock surface gas flow cross beam temperature measuring data, the evaluation system of stock surface gas flow distribution in radial direction and circumferential direction was established. Central index, platform index and edge index were proposed to evaluate stock surface gas flow distribution in radial direction, global uniform index and local uniform index were proposed to evaluate stock surface gas flow distribution in circumferential direction. Combined with actual production of 5500 m3 blast furnace and typical morphology of stock surface gas flow distribution,the strength of stock surface gas flow distribution was divided into five grades to provide guidance for the optimization of blast furnace operation.

Mar 1, 2017

By Jeff M. Kuhn

A new solvent extraction process for the removal of halides from zinc sulphate solution was tested in pilot plants at both a 0.1-L/min scale and at a 3-L/min scale. Teck Cominco?s process is called the HalogonTM process, for which patents are pending. Mixer-settlers were used for the 0.1-L/min pilot scale and two BATEMAN pulsed columns for the higher rates. Pilot testing was performed with commercial zinc sulphate solutions containing variable amounts of chloride and fluoride. Sulphate extraction was also controlled and deleterious halides were loaded and stripped into a form suitable for disposal. The engineering aspects and economics of this solvent extraction process for halide removal are also reported.

Jan 1, 2003

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995

By Salustio s. Guzman

The standard .free energies of formation of tin chlorides were estimated with reviewed and estimated basic thermodynamic data, and measured reversible potentials for the disproportionation of tin dichloride into metallic tin and tin tetrachloride. Values for cºp, Sº, Hº?-Hº 298, -(Gº - Hº298) /T,.Hºf, Gºf, and log Kp are given in tabular form, these estimations are compared with estimations reported in the literature.

Jan 1, 1985

By Jared Ball, Benjamin Hogg

There are over 100 process parameters that can be monitored during a single Peirce-Smith (PS) converter batch operation. To support a consistent operation it is important to select the correct Key Performance Indicators (KPI’s) to monitor. They should be strategically chosen to drive the desired behaviour with enough flexibility to endure process variations. At the Xstrata Copper Smelter in Mount Isa most of the PS converter operators have very little experience and are often lacking in the appropriate education or training to properly understand the process. For this reason 10 simple KPI’s were chosen that could be easily comprehended and monitored by all smelter personnel. KPI compliance has been supported by relevant project work in the converter area. Charge sequence trials have been performed in an effort to reduce splash and optimise activity time. The online measurement of full and empty ladle weights has enabled an immediate indication of skull size, skim/slag carryover, and metal loss.

Jan 1, 2009

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By Richard H. De Voto

The McDonald Gold Project and two satellite gold deposits near Lincoln, Montana, contain at least 9.9 million ounces of gold and 30 million ounces of silver. The McDonald gold deposit alone contains 7.2 million ounces of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $190 per ounce. The deposit is predominantly oxidized with no chance of acid production, and can be mined, operated, and reclaimed with minimal permanent environmental disturbance other than the creation of an open pit filled with a fresh-water lake which would support trout. The Seven-Up Pete Joint Venture, the owner of the McDonald Gold Project, commenced permitting of an open-pit, heap-leach operation in November 1994. In 1998, Montana citizens passed an anti-cyanide, open-pit mining initiative, 1-137, which banned any new open-pit gold mine which uses cyanide processing, The Venture has conducted extensive studies, including metallurgical testing of the treatability of McDonald ores with alternative lixiviants, and has determined that all other mining and metallurgical treatment systems are vastly uneconomical in the recovery of gold and silver from the McDonald deposit. Therefore, the Venture's proposed open-pit mining and cyanide heap-leach processing is the only technology that can be applied economically to the McDonald deposit. Further, the analyses convincingly demonstrate that the proposed open-pit, cyanide heap leaching technology results in maximum resource conservation of this valuable and unique deposit and poses far less risk to human health and the environment than any of the alternative technologies.

Jan 1, 1998

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Jesse White, Tyler Salisbury

Research projects contain many stages of development from the conception of an idea to a fullscale commercial operation. The transition from laboratory-scale research to bench-scale roasting can represent a significant increase in complexity and cost, depending on how many variables are being evaluated. Thermogravimetric analysis (TGA) can simulate roasting conditions and produce a small sample for chemical analysis or materials characterization. A simultaneous thermogravimetric and differential scanning calorimetry (TG–DSC) can identify endothermic and exothermic reaction temperatures. Using thermal analysis, some of the process variables can be tested and eliminated such as ore and reagent blends, retention times, operating temperatures, and some atmospheres.

Jan 1, 2015

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Guo Xueyi

The dissolution behaviors of valuable metals, lead and zinc, from secondary fly ash generated in municipal incineration plants were investigated using some lixiviants: sulfuric and hydrochloric acids, acetic acid and some chelating reagents including L-asparaginic-N,N-diacetic acid (ASDA), a biodegradable, and therefore, environmentally benign novel chelating reagent. It was found that zinc exists mainly as ZnO, whereas Pb probably as PbOHCI and PbO, and the easily soluble components in SFA are KCI and NaCl. Suitable amount of HCI can dissolve all of lead and zinc from SFA. Sulfuric acid can selectively extract zinc leaving lead in the residue. Ethylenediaminetetraacetic acid (EDTA) is an effective chelating reagent to extract both zinc and lead. Although ASDA and diethylene¬triaminepentaacetic acid (DTPA) can selectively extract more than half of lead from SFA, it would by no means be regarded as highly effective reagents for the extraction of these metal values. Keywords: Lead, Zinc, Secondary fly ash, Leaching, Dissolution

Jan 1, 2002

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By D. Tahija

The Getchell Mine produces gold from a geologically complex ore bearing high concentrations of arsenic and carbonate minerals. The mill treats the ore using high temperature aqueous oxidation in autoclaves, followed by conventional carbon-in-leach gold recovery. We laboratory tested a variety of Getchell ores to determine the effects on gold recovery of conventional factors such as grind size and retention time, as well as the influence of factors such as ore variability and preliminary carbonate destruction. Because the mill is currently operating, we were able to directly compare certain laboratory predictions with operational results.

Jan 1, 1999

By D. G. Schmidt

Tests were conducted on C86200 high-strength yellow brass in order to ascertain the effect of a low level of nickel on the mechanical properties on this alloy. A series of two alloys was studied, one of which had a nickel content of 0.85% and the other with <0.05% nickel. Copper and aluminum content ranged from 62.5% to 64% and 3.2% to 4.6%, respectively. When compared by zinc equivalents, a nickel addition of 0.75% in high-strength yellow brass does not act like copper but raises the tensile strength, 0.5% yield strength and BHN while lowering the elongation.

Jan 1, 1999