Search Documents

By Andreas Weber

Batrec operates a plant for the recycling of used dry batteries with a capacity of 3000 tons per year. The plant Is situated In a tourist area of Switzerland and has complied with all the strict emission restrictions. The process yields four products: FeMn. Zn, Hg and slag. No hazardous waste Is produced. All types of batteries can be treated.

Jan 1, 1995

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"In this study pertaining to the electrochemistry of chalcopyrite, the active/passive behavior of a chalcopyrite electrode in 0.5M sulfuric acid solution was investigated. Potentiostatic and potentiodynamic polarization and multi-cyclic voltanunetry were conducted to analyze the electrodissolution parameters of the electrode.The potentiodynamic and potentiostatic polarizations of chalcopyrite revealed the formation of a passive film on the surface of chalcopyrite. From the potentiostatic study in the passive potential region, a decrease in the dissolution current density by increasing the potential was observed. From this, it was concluded that the passive film is an n-type semiconductor and cation interstitial defects or anion vacancies are the charge carriers. From multi-cyclic voltammetry studies, four cathodic peaks at - 0.37, 0.30, -0.10 and-0.20 YsHE were detected on the surface of a passivated chalcopyrite electrode. The cathodic peaks at 0.37 and 0.30 V were connected to ferric to ferrous reduction and copper sulfide formation, respectively. The peaks at -0.10 and - 0.20 were related to chalcopyrite reduction. The products of the chalcopyrite reduction reactions were suggested to be Cu2S, Cu9fesS16 and Cu5feS4 and evolution of hydrogen sulfide gas (H2S).IntroductionChalcopyrite is the most abundant copper bearing mineral in the world and its dissolution behavior represents the most important technological consideration in the hydrometallurgical extraction of copper [I]. Since the current pyrometallurgical methods for copper extraction from chalcopyrite have environmental issues, many studies have considered the leaching and dissolution of CuFeS2 in different aqueous media [2-5]. The main problem associated with leaching processes is the slow dissolution rate of the mineral [6]. During the dissolution process, increasing the potential of the chalcopyrite in the anodic direction will cause the formation of surface layers which hinder the dissolution rate of the mineral [7]. The precise composition of the layers is in dispute. Previous studies have concluded that these layers could be sulfur [8-9], precipitated iron compounds [8], a solid electrolyte interphase (SEI) - which slows the rate of electron transfer- [10], a metal deficient sulfide [ll], or polysulfidic in nature [12-13]. In order to increase the leaching kinetics of chalcopyrite, the characterization of the layers formed during dissolution is essential and electrochemical methods are important to this end. Studies by Biegler [14] show nucleation and growth of a thin two-dimensional sulfide phase on the surface of chalcopyrite during the exposure of a polished sample in HzS04 solution or air. More studies by Biegler and Swift [15] have shown evidence for nucleation and growth of a 3-dimensional phase at low anodic potentials (around 200 mV vs. OCP). The current-time behavior of the dissolution process in this potential area has the characteristics of expansion and overlap of localized dissolution centers."

Jan 1, 2012

By Kwang-Ho Lee

The Onsan copper smelter of LS-Nikko Copper Inc. has operated the Mitsubishi continuous process along with Outokumpu process since 1997. Mitsubishi process is a bath smelting process which needs adequate melts for smelting reaction in the furnace. After a campaign shutdown it requires time to make a start melt. Onsan smelter has had much experience in flash smelting, including the improvement of the concentrate burner which is one of the most important parts in a flash smelting furnace. Based on this experience, the lances of the Mitsubishi smelting furnace were modified in order to making the starter melt with flash reaction. In 2004, the flash reaction in the Mitsubishi S-furnace was completed and was able to make the starter melt using these modified lances. Although at that time it was still under development it reduced the time required to make the initial bath-melt by about half.

Jan 1, 2006

By P. R. Khangaonkar

The variety of intermediates, middlings, complex materials and wastes produced in the conventional processing of tin ores as experienced in the tin industry in South East Asia is reviewed. The problems associated with the treatment of these materials so as to produce useful products by hydrometallurgical or pyro-cum-bydrometallurgical approaches are discussed. Results of treatment of amang middlings consisting of cassiterite, struverite, ilmenite, zircon, monazite etc by chlorination with carbon tetra chloride are presented. The efforts to leach tin without letting iron coming in, by alkali leaching of certain wastes of tin processing are also briefly indicated. It is felt that pyro-cum-hydrometallurgical approach can help a viable treatment of these materials so as to obtain usable or value added products.

Jan 1, 1994

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li

Sinter is an important iron-bearing material charged into blast furnace. Calcium ferrite (CF) is one of the most significant liquid phases in fluxed sinter. The isothermal reduction kinetics of CF and CF8M (n(CaO):n(Fe2O3) = 1, wt%(MgO) = 8) with 30% CO and 70% N2 gas mixtures at 1123, 1173, and 1223 K were investigated through thermogravimetric analysis in this study. Rate analysis illuminates that the reduction processes of CF and CF8M are mainly expressed as a typical two-stage reaction. Sharp analysis indicates that CF and CF8M reduction is expressed by the Avrami–Erofeev equation presenting a 2D shrinking layer reaction. The apparent activation energy values of CF and CF8M reduction are 46.9 and 31.8 kJ mol−1 individually based on model-free method.

Mar 1, 2018

By C. Wieckert

Concentrated solar energy can be used as heat source for the production of metals. One of the most promising respective processes, the solar carbothermic production of Zn from ZnO, is investigated within the European research project SOLZINC, a cooperation of institutes and industries from France, Germany, Israel, Sweden and Switzerland. The solar produced Zn can be used as commodity or as an energy carrier for further processing on demand to electricity in Zn-air fuel cells/batteries or to generate hydrogen by reaction with steam. In both cases the Zn is oxidized to form ZnO, which can be recycled back to the solar plant. In these cyclic processes Zn acts as a means to store and eventually transport solar energy. Second product of the solar process step is a CO-rich offgas, which may e.g. drive a gas engine or may be shifted to hydrogen in a conventional reaction with steam. A pilot plant using 300kW concentrated solar power input has been constructed and operated successfully. 86mass-% of ZnO mixed with 14mass-% of charcoal are reacted to produce Zn and CO at a temperature of about 1200°C, yielding about 50 kg gaseous Zn per hour. Zn-dust with 95% purity is recovered from the offgas system that was designed to produce Zn for Zn-air fuel cells. Based on the results and findings from the pilot plant, a two tons Zn/h solar demonstration plant has been designed conceptually. Cost studies have been performed and scenarios for producing electricity or H2 via these ZnO/Zn-cyclic processes are evaluated.

Jan 1, 2006

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995

By Theo Lehner

"The Boliden Rönnskär Smelter operates in the European Context of tight EH&S limits, with ever increasing regulations and tribulations. The near future promises to bring new burdens in the form of C02 trading, miners and pre-treaters increased appetite for a larger share of contained values, and changing compositions and competition in raw materials. On the other hand, European Smelters such as Rönnskär, Harjavalta have demonstrated an astonishing power of survival. This presentation lists and comments on current challenges but opportunities for increased survival power are also presented. One example of the latter is the ongoing investment into increased treatment capacity for e-scrap.UPDATE ON RÖNNSKÄR OPERATIONSThe Rönnskär Smelter has achieved 80 years of age with no signs of retirement. The smelter is most active in spite of its age! And it has undergone some face lift operations to maintain its attractiveness.Raw material, processing facilities and a market for the products are some essential prerequisites for a viable operation. To justify long term survival, economic terms such as return on investments and positive cash flow need to be considered. Below, we illustrate how the Rönnskär Smelter complies with these terms. To update the reader on current operations, our current flow sheet is depicted in Figure 1. The figure summarizes our current input and output."

Jan 1, 2012

By Ruiqing Li

It is possible to purify some liquid metals by exploiting the difference between the vapour pressure of the bulk metal and the minor constituents or impurities. The rates of purification can be improved by carrying out the process under reduced pressure, that is, so called, vacuum. Some commercial examples of vacuum refining are the purification of molten tin to eliminate trace amounts of lead and the refining of cobalt, also to remove lead. The objective of this paper is to review the basic theory behind vacuum refining technology in order to show how the feasibility of vacuum refining can be determined simply for a particular system by evaluating Olette's Volatility Refining Criteriont.

Jan 1, 1991

By James A. Sommers

Combustion of niobium nitride powder in a stream of oxygen results in several niobium oxide phases, depending upon reaction parameters. Under rapid oxygen flow, the oxidation produces a molten mass which coalesces into droplets of ca. 2 mm dimension and effectively quenches to leave NbO2 and other lower oxides of niobium, despite the ambient atmosphere of oxygen. A preliminary survey of reaction parameters which govern the split between reduced and oxidized products is presented. This technique offers novel synthesis means for binary oxides when mixtures of NbN and other materials are combusted together, since the niobium moiety is generated in a molten state.

Jan 1, 1995

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Continuous and aligned fiber composites provide the highest possible reinforcement for a polymeric matrix. In particular, the impact resistance is significantly increased in comparison with a low energy absorbed brittle polymer. For this reason, investigations have been carried out with both synthetic and natural fibers as a way to improve the toughness of polymeric composites. Among the natural fibers, ramie was not yet been studied for its reinforcement effect to make tougher polyester composites. Thus, the present work assesses the impact toughness of polyester composites incorporated with different amounts of ramie waste fibers.IntroductionIn most engineering and other technological areas, the use of materials associated with low energy processing conditions is gaining attention for the possible environmental benefits. This offered an incentive towards the substitution of natural renewable and biodegradable materials for the traditional energy intensive synthetic materials [1]. Natural fibers from both origins: animal, such as silk and wool, and vegetable, such as cotton and jute, are typical examples of those environmentally friendly materials. Low cost and highly reduced processing machinery wear are important advantages of the natural fibers over the most common synthetic ones such as glass fiber and nylon. For these reasons, polymeric composites reinforced with natural lignocellulosic fibers have nowadays been the subject of investigation [2,3].The mechanical strength is one important property of lignocellulosic composites to access the possibility of uses like structural materials for building parts such as doors and panels, as well as furniture. In this case, mechanically strong fibers like sisal, jute, curaua and ramie [4-7] are most convenient. Moreover, the relatively low fiber/matrix interfacial shear stress in these composites is associated with higher impact energy. In fact, a greater energy has to be expended for the rupture of a weak interface. The many cracks that are formed by impact tend to branch during the fiber pullout from the matrix [8]. A larger number of cracks correspond to a greater fracture surface and consequently higher toughness."

Jan 1, 2008

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Zhou Shu-cai

"A method has been proposed for the pre-treatment of high phosphorus iron ore by carbothermic reduction assisted with microwave irradiation and magnetic separation on a laboratory scale. Chemical analysis of the reduced ore sample, the metal sample and the slag sample were conducted. Based on the above research, the influences of carbon addition, microwave power and microwave irradiation time on the recovery of Fe and dephosphorization were discussed. It indicated that the increase of microwave irradiation time and power had substantial effect on the recovery of Fe while the influence of carbon addition was not obvious and the highest iron recovery ratio reaches some 95.5% when the dephosphorization ratio was 37.68%. A high iron recovery ratio and a reasonable dephosphorization rate were incompatible under the conditions investigated in this study due to the reduced iron and because unreduced P-contained gangues were not efficiently separated. This method may provide a reference for the future utilisation of high-phosphorus iron ore.IntroductionWith the rapid growth of crude steel production in China, the source of iron ore tends to become increasingly strained and is facing the risks of raw material shortage for the iron and steel industry. In order to decrease the production cost, China has to focus on the utilization of its domestic low grade iron ores for the iron and steel plants [1-2]. China has a large deposit of high phosphorous iron ore with a reserve of 7.45 billion tons which is unused in any large scale [3]. Therefore, the development of a successful and economically viable technology for high phosphorus iron ore is of profound importance. To remove phosphorus from the high phosphorus iron ore, several mineral and metallurgical processes have been proposed, such as bio-leaching [4], roasting reduction plus melting separation [5], pre-reduction and screening methods combined with mechanical crushing or air jet milling[6] selective agglomeration plus reverse flotation [7]. However these processes are not cost effective or are time consuming. The traditional pyrometallurgical process( BF+ BOF) refuse this kind of ore mainly because that molten iron is saturated with carbon or high carbon content and thus all phosphor us in the burden goes to the molten iron[8]. Therefore, it is important to exploit the cheap and abundant high phosphorus iron ore as a resource in ironmaking. In recent years, the microwave was widely introduced as a heat resource for extractive metallurgy of iron ore or other minerals. For example, microwave assisted ore milling, microwave assisted carbothermic reduction of metal oxides and microwave assisted mineral leaching issues[9-10]"

Jan 1, 2014

By Thomas Brynjulfsen, Merete Tangstad

"Manganese ore fines, generated during mining and transportation, can not be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore and subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace they are agglomerated into sinter, pellet or briquettes. The agglomeration process will however change the reduction properties of the ore. In this work the melting and reduction properties of sinter has been investigated.The melting temperature and melting mechanisms has been studied. The mineralogy of the raw ores and agglomerated has been found using XRD, and the composition established using EPMA(WDS). The effect of adding fluxes such as dolomite and quartz has also been investigated.IntroductionManganese metal is produced in a submerged electric arc furnace or in blast furnaces. The reduction of manganese oxide in blast furnace has in the recent years become more unusual due to the high consumption of reducing carbon material[5]. Manganese metal for alloying in steel usually contains silicon and iron, and are therefore called ferro manganese and silicomanganese.During mining, transportation and handling the manganese ore is broken up into different size fractions. The larger lump are used directly in the electric arc furnace, but the finer materials can not be added without treatment. The fine ore can disrupt the flow of CO and CO2 gas through the burden, subsequently reducing the degree of pre-reduction. The fine fractions must therefore be agglomerated into larger lumps, in order to promote gas flow. This can be achieved through a number of different processes. The agglomerate used in this work has been sintered, which means that is has been partly molten and reduced, in order to create bigger lumps."

Jan 1, 2012

By Zhihao Yue, Honglie Shen, Yahui Teng, Ye Jiang

"In this paper, manganous nitrate [Mn(NO3)z] was used to assist the etching of silicon wafer in hydrofluoric acid (HF) for the antireflective application, and alumina (Al2O3) layer was deposited on the surface of the etched sample by atomic layer deposition method for further antireflection. The surface morphological and compositional studies of these samples were performed by scanning electron microscopy attached with an energy-dispersive X-ray spectrometer. The surface reflectance measurements were carried out using UV-Vis-NIR spectrophotometer. Binary structures of pyramids and nanopores were obtained by etching the alkaline textured monocrystalline silicon wafer in HF and Mn(NO3)z mixed solution for not more than 15 min. But excessive increase of etching time of up to 30 min resulted in the whole destruction of pyramids. The average reflectances of the 5-min-etched sample before and after being coated with 75-nm-thick Al2O3 layer are 4.62% and 3.47% in the range of 200-1000 nm, respectively.1. IntroductionAs we know, the reflectance of silicon wafer after being sliced is so high that the maximal photoelectric conversion efficiency of silicon based solar cells is limited. Therefore, alkaline texturization process was used for silicon solar cell in industrial production. But the reflectance of this alkaline textured wafer is still greater than 10% and this process can only be used for monocrystalline silicon solar cell."

Jan 1, 2013

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By Peiye Yan, Huiqing Tang

To reduce coke consumption in blast furnace ironmaking, this study proposed a new method of applying iron-coke briquette prepared using hematite powder and pulverized coal to protect coke in BF iron making. Results showed that, with a ratio of hematite to coal of 2.0, the iron-coke briquette could obtain a satisfying compressive strength of more than 1500 N both before gasification and after being gasified by CO2 for 1 h. The activation energy of the iron-coke briquette was 93–135 kJ/mol, which is lower than the coke and therefore could protect the coke in BF. The agglomeration and stratification of iron particles occur in the course of iron-coke briquette gasi fication and is bene ficial to the improvement of the iron-coke briquette strength.

Mar 1, 2018